Conrad DHC 2 User manual

DE HAVILLAND
Radio control model / R/C Flugmodel
MONTAGEANLEITUNG
Or Electric equivalent
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan 112in.
Length 68 in.
Gas Engine 26 - 30cc
Radio 6 Channel / 8 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweiter 2.850mm
Lange .727mm
Verbrennerantrieb 26 - 30cc
Fernsteuerung 6 Kanal / 8 Servos
DHC 2
BEAVER
26 - 30cc Gas Engine

1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
Low setting
SILICON
EPOXY A
EPOXY B
CA
GLUE
Epoxy Glue (5 minute type)
Silicon sealer
Cyanoacrylate
Glue
Minimum 6 channel radio
for airplane with 8 servos
Nylon tube
Extension for aileron
servo, Flap servo.
REQUIRED FOR OPERATION (Purchase separately)
Epoxy Glue (30 minute type)
TOLLS REQUIRED
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors Wire Cutters
(Purchase separately)
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
(Purchase separately)
.Motor control x1 .Aileron x2
.Elevator x2 .Rudder x1
.Flap x 2
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the
model in a cool place will let the wrinkles disappear. Otherwise, remove
wrinkles in covering film with a hair dryer, starting with
low temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten
entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie
zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !
BENOTIGTE KOMPONENTEN FUR DEN ABFLUG (Nicht enthalten)
Klebstoff
Epoxy-Klebstoff (30min-Typ)
Epoxy-Klebstoff (5min-Typ)
Gas Engine: 26 ~ 30cc

FUSELAGE - REAR - BOTTOM VIEW
UNTERSICHT
1- Tail gear / Heckspornrad
2x6mm screw
.........3
1
2
3
4
6- Tail gear / Heckspornrad FUSELAGE - REAR - BOTTOM VIEW
UNTERSICHT
3- Landing gear / Fahrwerk
....2
5X50mm screw
3x10mm screw
.........4
2x6mm screw
2.5mm collar
.........2
3mm plywood
3mm plywood
3mm plywood
Aluminum landing gear
This hole is pre-drilled
at factory.
4mm
4mm
CA
1
2
3
4
1
3
Two holes on the landing gear
hatch are pre-drilled at factory
1.5mm
SIDE VIEW

Aluminum landing
gear
Hauptfahrwerk
5x50mm
screw
4mm nut
............2
5X50mm screw
.....................4
5mm nut
5mm washer
.....................6
5mm collar
...................2
! Securely glue together. If coming off during flight,
you lose control of your air plane.
6- Horizontal Stabilizer / Hohenleitwerk
6x22mm dowel
........2 TOP VIEW / Draufsicht
4- Landing gear / Fahrwerk
2x6mm screw
.........10
5- Landing gear / Fahrwerk
CA
CA
4mm
5
6
7
7
8
9
10

TOP VIEW / Draufsicht
7- Horizontal Stabilizer / Hohenleitwerk
AB
TOP VIEW / Draufsicht
8- Vertical Tail / Seitenruder
9- Vertical Tail / Seitenruder
AB
Cut away only
the covering
! Securely glue together. If coming off during flight,
you lose control of your air plane.
! Securely glue together. If coming off during flight,
you lose control of your air plane.
AB
BOTTOM - VIEW / Unteransicht
ELEVATOR ELEVATOR
Elevator push rod
Nylon push rod guider
* WARNING: When removing any covering from
the airframe, please ensure that you secure the
cut edge with CA or similar cement. This will
ensure the covering remain tight.
Control horn
................2
2x30mm screw
..........4

CA
Align the mark on “BCOW”
with the mark on the
fire-wall (FL1)
BCOW
FL1
12- Cowling / Motorhaube
TOP VIEW / Draufsicht
TOP VIEW / Draufsicht
CA
10- Vertical Tail / Seitenruder
11- Vertical Tail / Seitenruder
Rudder torque rod
Rudder push rod

BCOW
CA
150-150mm
13- Cowling / Motorhaube
14- Engine /
Motoreinbau
3x8mm screw
..............3
Blechschraube
15- Cowling / Motorhaube

Throttle servo
Rudder servo Elevator servo
BTC
1
2
1- Pull the BTC out of the hatch
2- Slide the hatch (as shown)
16- Fuel tank / Kraftstofftank
17- Battery installation
ABS Dummy engine
Dummy engine
Cowling
2x6mm screw
2x6mm screw
15A- Dummy engine

1
2
1- Install the LI-po battery into the box.
2- Pull the hatch (as shown).
X
Elevator pushrod
or rudder pusshrod
D=5/64”(2mm)
Tail wheel pushrod
D=.050”(1.2mm)
3mm set Screw
2 mm
Elevator pushrod
ELEVATOR / RUDDER SERVO
Connector
Connector
............2
............2
Gestangeanschluss
Gestangeanschluss
18- Battery installation
BTC
Reposition the BTC for secure the hatch in place.
19- Linkage / Anlenkungen

Control horn
...................2
2x30mm screw
..........4
......2
X
Aileron servo
extension
cord
Aileron servo / Querruder servo
TOP
Flap servo hatch Flap push rod
Push rod exit
1- Place the flap servo onto the servo mounts and secure it in place using the four screws included with the servo.
2- Install the flap push rod connector onto the hole in the flap servo arm and insert the push rod through the push rod
connector.
3- Place the flap servo hatch in its mount and secure it in place using four 2x10mm screws.
L/R
CAUTION: one of the flap servos is revert servo
2x10mm screw
20- Servo installation / Servoeinbau
5/64(2x10mm)
screw
5/64(2x10mm)
screw
Flap servo hatch
Flap servo Servo mount
Aileron servo hatch
Aileron servo Servo mount
WING BOTTOM
WING BOTTOM
Aileron servo hatch
Aileron push rod
Aileron control horn
21- Linkages / Anlenkungen
Wing - Bottom view / Unteransicht
BOTTOM
BOTTOM - VIEW / Unteransicht

Aluminum tube
22- Installing the wing / Tragflacheneinbau
Wooden dowel
AB
Wooden dowel
23- Installing the wing / Tragflacheneinbau
L/R
24- Installing the wing / Tragflacheneinbau
5x20mm screw
.....2
5mm washer
...............2 L/R

26- Installing the wing / Tragflacheneinbau
The hole on the bottom of the
wings and the slot on the side of
the fuselage are pre-drilled at
factory
Wing brace ( right - left)
To the bottom of the wing To the side of the fuselage
L/R
3x15mm screw / Schraube
............................2
Wing
3x15mm
sscrew
3x15mm
sscrew
The blindnut in the wing
is installed at factory.
Wing brace
90 ~ 95mm
30mm
15mm
Aileron
Rudder
27- Balance / Schwerpunkt
15mm
30mm
Querruderausschlag
Seitenruderausschlag
Do not try to fly an out-of balance model!
Uberprufen Sie vor dem Flug den Schwerpunkt. 15mm
15mm
Elevator
Hohenruderausschlag
Flap
20mm
All details are subject to change
without notice !
Technische Anderungen und Irrtumer
vorbehalten !
IMPORTANT:
Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner
to clean on surface of your model to keep the colour not fade.
This blindnut can be
move up and down
CA
CA
25- Decor / Aufkleber
Note: Cut out the stickers and apply them in the proper area.
Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off
with scissors. Arrange sticker on model and when satisfied adhere the corner without backing.
Carefully peel back the rest of the backing while at the same time adhering the rest of the
sticker.
Try not to make air bubbles, if there are some, carefully puncture sticker (center of bubble) but not model surface
with the tip of the knife or sharp pin and squeeze out the air.
At curves stretch sticker and apply a little heat so that no ceases occur. Cut off the excess that is produced.
1
2
3
4
1
2
3
4