Consonance LP6.1 User manual

LP6.1 Turntable
USER GUIDE
Congratulations on your new CONSONANCE!
Opera Audio products are based on a simple philosophy:
The component shall reproduce the original musical sound, purely and naturally.
The products are easy to operate and are manufactured according to the best quality
principles.
All CONSONANCE products are created with acoustical instruments in a concert situation
as point of reference. The music is reproduced exactly like the original and is limited only
by the quality of the recording.
Our aim is to give you the best possible music experience!
CONTENTS
Partlist p.1
Assembling the Turntable p.2
Technical specifications p.5
Use & Placement p.5
Cleaning p.5
Note&Warning p.6
Warranty p.7
Partlist
1. Platter
2. Plinth
3. Strobe disc
4.Record mat
5. Lubrication oil
6. 5mm allen wrench
7. Belt
8. T988 tone-arm
9. Power supply socket
10.Speed adjustment POT
11. On-off switch

Assembling the Turntable
1.Take out the plinth.
2.Fill the bearing with lubrication oil supplied to a level of approx 5mm above the bottom bearing.

3. Installing the platter.Put on the cotton gloves and pick up the acrylic platter, with the dip for the record
label uppermost. Hold it level over the bearing housing, locate it carefully and gently lower it until it seats fully
over the bearing.
4.Installing the belt.Start with the belt
around the motor pully,take care the
other end clears the centre spindle and
rotate the platter,the belt will track
around the platter.

4.There are two ruts on the pulley
of motor. The above rut is for 33.3
rpm, and the other rut is for 45
rpm. Different ruts for the different
speed.
5.Fitting the cartridge and tonearm adjustments.Please take tonearm manual as reference.The tonearm
VTA adjustment should be according to the pictures below.
If you want to use 12" tonearm,you
can buy T1288 exra
armshaft.Then replacement the
plinth according to the pictures
below.

⑩is for tiny speed adjustment.If the speed has small distinction,you can use strobe disc to test and
adjust ⑩.
Motor power supply use DC 12V.
TECHNICAL SPECIFICATION
Wow and Flutter: Less than 0.03
Rumble: Greater than 80dB down
Speed accuracy: Within 0.01%
Motor power : DC 12V

USE & PLACEMENT
The Consonance LP6.1 should be placed on a flat, hard surface for proper standing. The turntable
performs best after being switched on for 5 minutes for running smooth. A certain space is required for
tonearm moving above the turntable on the right side. The turntable must never be placed on a soft or
unstable base. Nor must it be covered while in use or placed on a narrow shelf or in another confined
space.
CLEANING
The base of the turntable and turnarm as well as the motor are made of solid, powder coated aluminum.
Fingerprints can be removed with a cloth moistened with warm water. A silk cover would be the best
keeping dust away from the whole LP system.
NOTE & WARNING
Opening of the product by non-authorized personnel will void the guarantee.
The products must not be exposed to rain or moisture.
Motor should only be opened or serviced by certified technicians. The devices contain electronic
components that can cause severe electric shock. Work performed on Consonance products by
unqualified personnel can cause serious damage and personal injury.

WARRANTY
Opera audio guarantees each product manufactured by us to be free from defects in materials and
workmanship under normal use. Our obligation under this warranty is limited to making good at our
factory any part or parts thereof which shall, within 1 year after delivery to the original purchaser, be
returned to us with transportation charges prepaid, and which an examination shall disclose to have
been thus defective; this warranty being expressly in lieu of all other warranties expressed or implied
and of all other obligations or liabilities on our part. This warranty shall not apply to any Opera audio
product which shall have been repaired or altered outside of our factory in any way so as to affect its
stability, nor which has been subject to misuse, negligence or accident. Warranties of the vacuum tubes
are by the respective manufacturers, usually 90 days.
Please mail or e-mail the Registration Card to the address as follows:
The Opera Audio Co., Ltd.
No.2 JianXianQiaoLu
ChaoYang District
Beijing, China
Tel: [phone]
Fax: [phone]
[email protected]
www.opera-consonance.com Registration Card
Name
Address
City
State
Zip
Email
Telephone
Model
Serial Number
Purchase Date
Dealer