Continental Fireplaces CDI-30N User manual

1
W415-0446 / H / 02.02.12
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INVIDIDUALS ALONE WITH THE APPLIANCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • Fax [phone] • www.continentalfireplaces.com • ask@continentalfire.on.ca
1.24B
$10.00
CERTIFIED FOR CANADAAND UNITED STATES USING ANSI/CSAMETHODS.
SAFETY INFORMATION
!WARNING
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the supplier.
If the information in these instructions
are not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
CERTIFIED UNDER CANADIANAND AMERICAN NATIONAL STANDARDS: CSA 2.22, ANSI Z21.50 FOR VENTED GAS FIREPLACES.
CDI-30N
NATURAL GAS
CDI-30P
PROPANE

2
W415-0446 / H / 02.02.12
TABLE OF CONTENTS
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 MINIMUM CLEARANCE TO COMBUSTIBLES 5
2.3 GENERAL INSTRUCTIONS 5
2.4 GENERAL INFORMATION 6
2.5 RATING PLATE INFORMATION 7
3.0 INSTALLATION 8
3.1 LEVELLING THE APPLIANCE 8
3.2 CHIMNEY CONNECTION 8
3.3 GAS INSTALLATION 10
3.4 OPTIONAL WALL SWITCH 10
4.0 FINISHING 11
4.1 MINIMUM MANTEL CLEARANCES 11
4.2 DOOR REMOVALAND INSTALLATION 12
4.3 GRATE INSTALLATION 12
4.4 LOG PLACEMENT 13
4.5 OPTIONAL CHARCOAL EMBERS 14
4.6 GLOWING EMBERS 14
4.7 LOGO PLACEMENT 14
5.0 BLOWER REPLACEMENT 15
6.0 OPERATION 16
7.0 ADJUSTMENTS 17
7.1 PILOT BURNER ADJUSTMENT 17
7.2 VENTURI ADJUSTMENT 17
7.3 FLAME CHARACTERISTICS 17
8.0 MAINTENANCE 18
8.1 CARE OF GLASS 18
8.2 DOOR GLASS REPLACEMENT 19
9.0 REPLACEMENTS 20
10.0 TROUBLE SHOOTING 24
11.0 WARRANTY 26
12.0 SERVICE HISTORY 27
NOTE: changes, other than editorial, are denoted by a vertical line in the margin.

3
W415-0446 / H / 02.02.12
1.0 INSTALLATION OVERVIEW
Venting, see “INSTALLATION
- CHIMNEY CONNECTION”
section.
Logs, see “FINISHING
- LOG PLACEMENT”
section.
Grate, see “FINISHING -
GRATE INSTALLATION”
section. Rating Plate, see
“RATING PLATE
INFORMATION”
section.

4
W415-0446 / H / 02.02.12
2.0 INTRODUCTION
3.1C
!
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• ANY CHANGES TO THIS APPLIANCE OR IT’S CONTROLS CAN BE DANGEROUS AND IS PROHIBITED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
according to operating instructions could cause fire or injury.
• Risk of fire or asphyxiation do not operate appliance with fixed glass removed.
• Do not connect 110 volts to the control valve.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be
sharp.
• Do not burn wood or other materials in this appliance.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or
clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers,
young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep
toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces.
These screens and guards must be fastened to the floor.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• The appliance is a vented gas-fired appliance. Do not burn wood or other materials in the appliance.
• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance
and venting system are kept clean. The appliance and its venting system should be inspected before use and at least
annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting,
bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
• Under no circumstances should this appliance be modified.
• This appliance must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.
• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any gas control which has been under water.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done
by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust
fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these
openings can also cause the surrounding combustible materials to overheat and catch fire.Only doors / optional fronts
certified with the unit are to be installed on the appliance.
• Only doors / optional fronts certified with the unit are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic
bags, these are not toys and should be kept away from children and infants.
• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as
having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated
temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a
T.V. or other electronic components.
• This appliance uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple supplied by
Wolf Steel Ltd.

5
W415-0446 / H / 02.02.12
2.1 DIMENSIONS
27
1
/ 4 "
19
5
/ 8 "
17
7
/ 8 "18
3
/ 4 "
30
1
/ 16 "
11
1
/ 8 "
5
1
/ 4 "
1
3
/ 8 "
23
1
/ 8 "
21
3
/ 4 "
3" ø collars
13
3
/ 4 "13
3
/ 4 "
THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to
conform with local codes. Installation practices vary from region to region and it is important to know the
s
p
ecifics that a
pp
l
y
to
y
our area
,
for exam
p
le in Massachusetts State:
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.
PROVIDE ADEQUATE VENTILATION.
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE
FRONT FACE OF THE APPLIANCE.
SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT
WHEN THE APPLIANCE IS OPERATING.
FIRE RISK. EXPLOSION HAZARD.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE
TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG.
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.
USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING
COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.
!
WARNING
Thisappliance mustberecessedinto aventednoncombustible wood-burning appliance(prefabricatedor masonry)
only. The minimum appliance opening size in which the appliance is to be installed is:
HEIGHT 21.75" WIDTH 28" DEPTH 18"
The minimum allowable chimney flue size is 6" round.
The minimum distance, from the bottom of a combustible mantle projecting 3" maximum from the wall to the
top of the louvre opening, is 12".
2.2 MINIMUM CLEARANCE TO COMBUSTIBLES
2.3 GENERAL INSTRUCTIONS

6
W415-0446 / H / 02.02.12
64.5%
CDI-30
2.4 GENERAL INFORMATION 4.12
• This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth
of Massachusetts.
• The appliance damper must be removed or welded in the open position prior to installation of a appliance
insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches.
• A Carbon Monoxide detector is required in all rooms containing gas fired appliances.
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent
sealed combustion product.
The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
Installation Code CSA B149.1 in Canada, or the National
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or
A
NSI Z223.1 and NFPA 54 in the United States.
Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must
be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian
Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace
Institute
® (NFI) as NFI Gas
Specialists
www.ncertied.org
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND
QUALITY!
CDI-30
NG LP
Altitude (FT) 0-4,500 0-4,500
Max. Input (BTU/HR) 24,500 24,500
Max. Output (BTU/HR) 20,825 20,825
Efficiency (w/the fan on) 85% 85%
A.F.U.E. (maximum value) 82% 82%
Min. Inlet Gas Supply Pressure 4.5" Water Column 11" Water Column
Max. Inlet Gas Supply Pressure 7" Water Column 13" Water Column
Manifold Pressure (Under Flow Conditions) 3.5" Water Column 10" Water Column
When the appliance is installed at elevations above 4,500ft, and in the absence of specific recommendations from the
local authority having jurisdiction, the certified high altitude input rating shall
be reduced at the rate of 4% for each additional 1,000ft. Expansion / contrac-
tion noises during heating up and cooling down cycles are normal and to be
expected.
This appliance is not approved for closet or recessed installations. It is ap-
proved for bathroom, bedroom and bed-sitting room installations and is suit-
able for mobile homes. The natural gas model is suitable for installation in a
mobile home that is permanently positioned on its site and fuelled with natural
gas.

7
W415-0446 / H / 02.02.12
2.5 RATING PLATE INFORMATION
INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model, venting and gas type of the appliance.
For rating plate location, see “INSTALLATION OVERVIEW” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
MODEL MODEL
GDI-30N / CDI-30N GDI-30P / CDI-30P
0-4500FT ALTITUDE / ELEVATION 0-4500FT
24,500 BTU/h INPUT /ALIMENTATION 24,500 BTU/h
15,000 BTU/h REDUCED INPUT /ALIMENTATION REDUITE 19,000 BTU/h
W385-0292 / H
GDI/CDI-30
CE FOYER UTILISE ET REQUIERT UN THERMOCOUPLE À ACTION RAPIDE. REMPLACEZ
UNIQUEMENT AVEC UN THERMOCOUPLE À ACTION RAPIDE DE WOLF STEEL LTÉE. HOMOLOGUE
POUR INSTALLATION DANS UNE CHAMBREACOUCHER, UNE SALLE DE BAIN ETUN STUDIO.
APPROPRIE POUR INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION
CONFORME AUX EXIGENCES DE LANORME CAN/CSAZ240MH SERIE DE MAISONS MOBILES
EQUIPEES AU GAZ, EN VIGUEUR AU CANADA A OU AUX ETATS-UNIS DE LA NORME DE
SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION
3280. DANS LE CAS OU CETTE NORME D’ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE
REFERER A LA NORME RELATIVE AUCRITERE DE MESURES DE SECURITE CONTRE
L’INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURERS, LES SITES ET
LES COMMUNAUTES, ANSI/NFPA 501A.
WOLF STEEL LTD.
24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA
9700539 (WSL) 4001657 (NGZ)
4001658 (NAC) 4001659 (WUSA)
CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA2.22b-2009,ANSI Z21.50b-2009 VENTED GAS FIREPLACE / FOYER AU GAZ AVAEC EVACUATION.
THIS FIREPLACE USES AND REQUIRES A FASTACTING THERMOCOUPLE. REPLACE ONLY WITHA
FASTACTING THERMOCOUPLE SUPPLIED BY WOLF STEELLTD.
APPROVED FOR BEDROOM, BATHROOM & BEDSITTING ROOM INSTALLATION. SUITABLE
FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT
STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN
THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD,
TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE
STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES
AND COMMUNITIES, ANSI / NFPA 501A.
MINIMUM AND MAXIMUM VERTICAL VENT LENGTHS ARE 10 FEETAND 35 FEET RESPECTIVELY. LES
LONGUEURS VERTICALES MINIMALES ET MAXIMALES SONT 10 PIEDS ET35 PIEDS RESPECTIVEMENT.
MANIFOLD PRESSURE: 3.5” W.C. (NG)
PRESSION AU COLLECTEUR: 3,5” D’UNE COLONNE D’EAU (GN)
MIN. SUPPLY PRESSURE: 4.5” W.C. (NG)
PRESSION D’ALIMENTATION MIN: 4,5” D’UNE COLONNE D’EAU (GN)
MAX. SUPPLY PRESSURE: 7” W.C. (NG)
PRESSION D’ALIMENTATION MAX: 7” D’UNE COLONNE D’EAU (GN)
MINIMUM AND MAXIMUM VERTICAL VENT LENGTHS ARE 10 FEETAND 35 FEET RESPECTIVELY. LES
LONGUEURS VERTICALES MINIMALES ET MAXIMALES SONT 10 PIEDS ET35 PIEDS RESPECTIVEMENT.
MANIFOLD PRESSURE: 10” W.C. (LP)
PRESSION AU COLLECTEUR: 10” D’UNE COLONNE D’EAU (P)
MIN. SUPPLY PRESSURE: 11” W.C. (LP)
PRESSION D’ALIMENTATION MIN: 11” D’UNE COLONNE D’EAU (P)
MAX. SUPPLY PRESSURE: 13” W.C. (LP)
PRESSION D’ALIMENTATION MAX: 13” D’UNE COLONNE D’EAU (P)
NOT FOR USE WITH SOLID FUEL
FOR USE WITH GLASS DOORS CERTIFIED WITH THIS UNIT ONLY.
WARNING: DO NOTADD ANYMATERIALTO THE APPLIANCE, WHICH WILLCOME IN CONTACT
WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE.
ELECTRICAL RATING: 115V 1.5AMP 60HZ
THE APPLIANCE MUSTBE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS. SEE
OWNERS INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND
RESEALING IS NECESSARYAFTER SERVICING THE VENT-AIR INTAKE SYSTEM.
WARNING: FOR INSTALLATION INTO AVENTED NON-COMBUSTIBLE FIREPLACE ONLY. THE
MINIMUM FIREPLACE SIZE IS: HEIGHT 21.75”, DEPTH 18”, WIDTH 28”. THE MINIMUM INSIDE FLUE
SIZE IS 6”. THE MINIMUM DISTANCE, FROM THE BOTTOM OFA COMBUSTIBLE MANTEL
PROJECTING AMAXIMUM 3” FROM THE WALLTO THE TOP OFTHE UNIT IS 12”. SEE OWNERS
MANUAL FOR GREATER EXTENSIONS.
UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC
CET APPAREIL
UTILISER AVEC LES PORTES VITREES HOMOLOGUEES SEULEMENTAVEC CETTE UNITE.
AVERTISSEMENT: N’AJOUTEZ PAS ACET APPAREILAUCUN MATERIAU DEVANT ENTRER EN CONTACT
AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNIAVEC CETAPPAREILPAR LE FABRICANT.
CLASS: 115V 1,5AMP 60HZ
L’APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L’ENSEMBLE D’EVACUATION PROPRE AWOLF
STEEL. REFERERAU MANUEL D’INSTALLATION DE PROPRIETAIRE POUR L’EVACUATION PRECISE. IL
EST IMPORTANT DE BIEN REINSTALLER ET RESCELLER L’EVENTAPRES AVOIR ASSURE LE MAINTIEN
DU SYSTEME DE PRISE D’AIR.
ATTENTION: POUR INSTALLATION DANS UN FOYER VENTILE EN MACONNERIE. LES DIMENSIONS
MINIMUMS SONT: HAUTEUR 21,75”, PROFONDEUR 18”, LARGEUR 28”. LE DIAMETRE INTERIEUR
MINIMUM DE CONDUIT D’EVACUATION EST 6”. LA DISTANCE MINIMALE, DU BAS DU MANTEAU
COMBUSTIBLE FORMANT UNE PROJECTION MAXIMALE DE 3” DU MURAU DESSUS DE LA GARNITURE
NORMALE EST 12” REFERERAU MANUEL D’INSTALLATION POUR DES EXTENSIONS PLUS GRANDES.
SAMPLE
ALTITUDE / ELEVATIONALTITUDE / ELEVATION
INP
U
T
/
ALIMENTATI
O
N
INPUT / ALIMENTATION
UCED INPUT /ALIMENTATION REDUITUCED INPUT /ALIMENTATION RE
SAMPLE
SAMPLE
PL
ET REQUIERT UN THERMOCOUPLE À
EQUIERT UN THERMOCOUPLE
UN THERMOCOUPLE À ACTION RAPIDE DEOCOUPLE À ACTION RAPIDE D
ALLATION DANS UNE CHAMBRE A COUCHEUNE CHAMBRE A COUCHE
RIE POUR INSTALLATION DANS UNE MAATION DANS UNE M
ORME AUX EXIGENCES DE LANORME CAN/RME AUX EXIGENCES DE LANORME CAN
UIPEES AU GAZ, EN VIGUEUR AU CANADAPEES AU GAZ, EN VIGUEUR AU CANAD
ECURITE ET DE CONSTRUCTION DE MAISOECURITE ET DE CONSTRUCTION DE MAISO
3280. DANS LE CAS OU CETTE NORME80. DANS LE CAS OU CETTE NORM
REFERER A LA NORME RELATIVE AURER A LA NORME RELATIVE
L’INCENDIE POUR LES INSTALLATIONSL’INCENDIE POUR LES INSTALLATION
TD.
D.
BARRIE, ON, L4M 0G8 CANADARRIE, ON, L4M 0G8 CANAD
4
001657
(
NGZ
)4001657 (NGZ)
4
001659
(
WUSA
)4001659 (WUSA)
P
P
P
REPLACE / FOYER AU GAZ AVAEC EEPLACE / FOYER AU GAZ AVAEC E
RESPECTIVELY. LESPECTIVELY. LES
DS RESPECTIVEMENT.ECTIVEMENT.
RESSURE:ESSU
3.5” W.C.
(
NG
)5” W.C. (NG)
UNE COLONNE D’EAU (GN)UNE COLONNE D’EAU (GN)
LY PRESSURE:Y PRESSURE:
4.5” W.C.
(
NG
)4.5” W.C. (NG)
,5” D’UNE COLONNE D’EAU (GN)D’UNE COLONNE D’EAU (GN)
SUPPLY PRESSURE:PLY PRESSURE:
7” W.C.
(
NG
)7” W.C. (NG)
MAX:
7” D’UNE
CO
L
O
NNE D’EAU
(G
N
)NE COLONNE D’EAU (GN)
MINIMUM AND MANIMUM AND M
LONGUEURS VGUEURS V
MANIFOLD PMANIFOLD
PRESSIONPRE
MIN. SUMIN. S
PREPRE
MAM
OLID FUELOL
IT ONLY.T ONLY.
ANCE, WHICH WILL COME IN CONTACTANCE, WHICH WILL COME IN CONTACT
Y THE MANUFACTURER WITH THE APPLIANTHE MANUFACTURER WITHTHE APPLIA
APPROPRIATE WOLF STEEL VENT KITS. SRIATE WOLF STEEL VENT KITS.
ING SPECIFICS. PROPER REINSTALLATIONCS. PROPER REINSTALLATIO
CING THE VENT-AIR INTAKE SYSTEM.AIR INTAKE SYSTEM.
ENTED NON-COMBUSTIBLE FIREPLACE ONENTED NON-COMBUSTIBLE FIREPL
T 21.75”, DEPTH 18”, WIDTH 28”. THE MINIMT 21.75”, DEPTH 18”, WIDTH 28”. THE
CE, FROM THE BOTTOM OFA COMBUSTIBLEE, FROM THE BOTTOM OFA COMBUS
OM THE WALL TO THE TOP OF THE UNIT ISM THE WALL TO THE TOP OF THE UNIT I
NSIONS.
SIONS.

8
W415-0446 / H / 02.02.12
3.0 INSTALLATION
3.1 LEVELLING THE APPLIANCE
Move the appliance close to its final position inside the wood-burning appliance. This appliance is equipped
with 4 levelling screws located in the four inside corners beneath the log support. Level using the levelling
screws to eliminate rocking or excessive noise when the fan is in operation. Once the appliance is level, move
it partially into place within the appliance to allow for all connections to be made. It is not practical to level the
appliance once it has been installed. Determine the required depth prior to installing the appliance and adjust
the four levelling screws accordingly.
68.4A
Clean out ashes from the inside of the wood-burning appliance. Make sure that the chimney and wood-burning
appliance are in a clean and sound condition and constructed of non-combustible materials. If necessary have
any repair work done by a qualified person before installing the insert. Remove the existing appliance damper
or lock into an open position.
Using screws, attach the appliance warning tag
to the inside of the firebox of the appliance into
which the insert is being installed.
The sheet-metal parts of the appliance, in which
the gas appliance insert is to be installed, must
not be cut.
If the wood-burning factory-built appliance has
no gas access hole(s) provided, an access hole of 1½ inch or less may be drilled through the lower sides or
bottom of the appliance in a proper workman like manner. This access hole must be plugged with non-combus-
tible insulation after the gas supply line has been installed.
Ensure that existing chimney cleanouts fit properly.
The refractory, glass doors, screen rails, screen mesh and log grates may be removed from the existing appli-
ance before installing the gas appliance insert.
Smoke shelves, shields and baffles may be removed if attached by mechanical fasteners.
The ventilation openings in the existing appliance may be obstructed by the backer plates, aluminium trim etc.
but these parts are not to be applied so as to have an airtight seal.
!
WARNING
RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.
W385-0199_B
WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITH AGAS FIREPLACE
INSERT ONLY AND CANNOT BE USED FOR BURNING WOOD OR SOLID FUELS UNLESSALL ORIGINAL
PARTS HAVE BEEN REPLACED AND THE FIREPLACE IS RE-APPROVED BY THE AUTHORITY HAVING
JURISDICTION.
ATTENTION:CE FOYER AETE CONVERTIAFIN D’ETRE UTILISE SEULEMENT
COMME FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU
TOUTAUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALESAIENT
ETE REMPLACEES ET QUE LE FOYER SOITAPPROUVE DE NOUVEAU PAR LES AUTORITES
AYANT JURIDICTION.
ADVERTENCIA: ESTA CHIMENEASE REMODELÓ PARA USARSE SOLO CON UNA
INSERCIÓN DE CHIMENEAA GAS Y NO PUEDE USARSE PARA QUEMAR MADERANI COMBUSTIBLES
SÓLIDOS, A MENOS QUE SE HAYAN REEMPLAZADO TODAS LAS PIEZAS ORIGINALES, Y LAAUTORI-
DAD JURISDICCIONAL LA HAYA VUELTO AAPROBAR.
3.2 CHIMNEY CONNECTION
Chimney installation must conform to both national and local code requirements. The chimney must be lined
with one 2" or 3" diameter liner for intake and one 3" diameter liner for exhaust. The minimum and maximum
vent lengths are 10 and 35 feet respectively. Recommended kits come in 3 lengths:
1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST & 2-3" TO 2" REDUCER:
GDI-2320KT VENT KIT 20FT
GDI-2325KT VENT KIT 25FT
GDI-2335KT VENT KIT 35FT
2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:
GDI-320KT VENT KIT 20FT
GDI-325KT VENT KIT 25 FT
GDI-335KT VENT KIT 35 FT

9
W415-0446 / H / 02.02.12
While the liners must be continuous from the appliance to the chimney cap, to
achieve the needed length, they may be coupled, using an approved coupler.
We recommend that exhaust vents that pass through unheated spaces,
such as tall exterior chimneys, be wrapped in a protective sleeve to minimize
condensation and reverse flow symptoms. See Trouble Shooting for details.
This appliance is approved for use with a 2" liner for air intake and a 3" liner
for exhaust. For best performance, however, it is recommended to use two 3"
liners.
If a 2" liner is used for the intake, it may be necessary to adjust the primary air
shutter.
A. OUTSIDE: Slip the one end of
a liner a minimum of 2" over
the sleeve of the air terminal.
Secure using 3 screws. Then
seal the joint and screw heads
with high temperature sealant.
Repeat with the other liner.
NOTE: We recommend that
the other end of the exhaust
liner be marked to eliminate
the exhaust liner being
connected to the intake
collar at the appliance.
B. Gently stretch the liners to the required
lengths and insert into the chimney. Trim
and fit the flashing plate to suit the chimney
termination. Place the air terminal onto the
top of the chimney. Make weather tight by
sealing with caulking (not supplied). Fasten
to the chimney with screws and plugs (not
supplied).
C. INSIDE: Remove the securing screw from
the front of the vent mounting plate. Pull
the vent mounting plate only, back into the
track, to the front stop. Start the slider back
into position. Re-secure the screw. The
appliance may now be pushed into its final
position inside the wood burning appliance,
and the screw tightened until the slider has
been pulled tight to the front stop.
D. Route the flex liners through the slider. Attach and secure the liners to the vent mounting plate using
the same procedure as before, ensuring that the marked exhaust liner is attached to the exhaust collar.
FLASHING
PLATE
2” OVERLAP
SEALANT
HI-TEMP
INTAKE
EXHAUST
MOUNTING
PLATE
SECURING
SCREW
INTAKE
EXHAUST
2"
OVERLAP
HI-TEMP
SEALANT
2"
LINER
3"
LINER
SLIDER
REDUCER
CONNECTION
ILLUSTRATED WITH A 2"
INTAKE LINER.

10
W415-0446 / H / 02.02.12
3.3 GAS INSTALLATION
3.4 OPTIONAL WALL SWITCH
For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient
location. Route a 2 strand, solid core millivolt wire from the valve to the wall switch or millivolt thermostat. The
recommended maximum lead length depends on wire size:
WIRE SIZE MAX. LENGTH
14 gauge 100 feet
16 gauge 60 feet
18 gauge 40 feet
Disconnect the existing wires from terminals 1 and 3 (from the
ON/OFF switch) and replace with the leads from the wall switch / millivolt thermostat.
50.1
3
1
2
!
WARNING
DO NOT CONNECT EITHER THE WALL SWITCH, THERMOSTAT OR GAS VALVE DIRECTLY TO 110
VOLT ELECTRICITY.
30.1A
Installation and servicing to be done by a qualified installer.
A. Move the appliance into position and secure.
B. If equipped with a flex connector the appliance is designed to accept a 1/2” gas supply. Without the
connector it is designed to accept a 3/8” gas supply. The appliance is equipped with a manual shut off
valve to turn off the gas supply to the appliance.
C. Connect the gas supply in accordance to local codes. In the absence of local codes, install to the
current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI
Z223.1 / NFPA 54 in the United States.
D. When flexing any gas line, support the gas valve so that the lines are not bent or kinked.
E. The gas line flex-connector should be installed to provide sufficient movement for shifting the burner
assembly on it’s side to aid with servicing components.
F. Check for gas leaks by brushing on a soap and water solution. Do not use open flame.
!
WARNING
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS
SPARKS OR OPEN FLAMES.
SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT
WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE
PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT
THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND
ELECTRICAL LOCATIONS, SEE “DIMENSION” SECTION.
ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG.
VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.

11
W415-0446 / H / 02.02.12
4.0 FINISHING
Combustible mantel clearance can vary according to the mantel depth.
Use the graph to help evaluate the clearance needed. These same
requirements apply to any combustibles protruding on either side of the
appliance.
3
12
5
4
MANTEL DEPTH
0
H
E
,
*
H
T
M
A
N
T
E
L
6
13
14
15
!
WARNING
RISK OF FIRE, MAINTAIN ALL SPECIFIED AIR SPACE CLEARANCES TO COMBUSTIBLES. FAILURE
TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE A FIRE OR CAUSE THE APPLIANCE TO
OVERHEAT. ENSURE ALL CLEARANCES (I.E. BACK, SIDE, TOP, VENT, MANTEL, FRONT, ETC.) ARE
CLEARLY MAINTAINED.
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION. 73.1
!
WARNING
RISK OF FIRE!
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
THE FRONT OF THE APPLIANCE MUST BE FINISHED WITH ANY NON-COMBUSTIBLE MATERIALS
SUCH AS BRICK, MARBLE, GRANITE, ETC., PROVIDED THAT THESE MATERIALS DO NOT GO
BELOW THE SPECIFIED DIMENSION AS ILLUSTRATED.
DO NOT STRIKE, SLAM OR SCRATCH GLASS. DO NOT OPERATE APPLIANCE WITH GLASS
REMOVED, CRACKED, BROKEN OR SCRATCHED.
FACING AND/OR FINISHING MATERIAL MUST NEVER OVERHANG INTO THE APPLIANCE OPENING.
72.1A
4.1 MINIMUM MANTEL CLEARANCES

12
W415-0446 / H / 02.02.12
The upper louvres must be removed to allow the door
to be opened or closed. To access the lower door latch,
open the valve control door. Release the top and bottom
door latches, located at the right side of the door.
NOTE: The protective wrap on plated parts is best
removed when the assembly is at room temperature
but this can be improved if the assembly is warmed,
using a hair dryer or similar heat source.
4.2 DOOR REMOVAL AND INSTALLATION
DOOR LATCH
!
WARNING
GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.
THE DOOR LATCHES ARE PART OF A SAFETY SYSTEM AND MUST BE PROPERLY ENGAGED. DO
NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.
FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR
OPENINGS, LOUVRES OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR
SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.
BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO
THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.
75.1
A. Remove the 3 screws from the location shown in
the base of the firebox.
B. Secure the grate to the firebox base using the 3
screws removed.
4.3 GRATE INSTALLATION

13
W415-0446 / H / 02.02.12
4.4 LOG PLACEMENT
!
WARNING
FAILURE TO POSITION THE LOGS IN ACCORDANCE WITH THESE DIAGRAMS OR FAILURE TO USE
ONLY LOGS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY
DAMAGE OR PERSONAL INJURY.
LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT MODIFY THE
PROPER LOG POSITIONS, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY AND DELAYED
IGNITION MAY OCCUR.
THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE.
76.1A
PHAZERTM logs and glowing embers exclusive to Continental Fireplaces, provide a unique and realistic
glowing effect that is different in every installation. Take the time to carefully position the glowing embers for a
maximum glowing effect.
Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour
pigments burn in during the heat activated curing process.
A. Place the back log (#1)
onto the log support tray
and in front of the tabs.
The tabs maintain an
air space between the
log and firebox back to
facilitate combustion air
flow. Ensure that the
back of the log rests
against the brackets
on the back wall of the
firebox.
D. Position the base end of
the center log (#5)against
the middle grate post with
the other end of the log
resting in the pocket of the
left crossover log.
B. Move the two small
logs (#2 & #3) into
position, lining up the
studs located on the
burner with the holes
on the bottom of the
logs. Ensure that the
small logs sit flat on the
burner.
E. Place the bottom of the
right crossover log (#6)
against the right firebox
side and pulled forward
to the grate. The top of
the log should rest in
the pocket provided on
the center log (#5).
C. Place the bottom of the
left crossover log (#4)
against the left firebox
side and pulled forward
to the grate. The top of
the log should rest in the
pocket on the back log.

14
W415-0446 / H / 02.02.12
Tear the embers into pieces and place along the front row of ports covering all of the burner area in front of
the small logs. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed
edges of the fibre hairs will glow. The ember material will only glow when exposed to direct flame; how-
ever, care should be taken to not block the burner ports.
Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PHAZERTM
logs glow when exposed to direct flame. Use only certified "glowing embers" and PHAZERTM logs available
from your authorized dealer / distributor.
32.1
Randomly place the charcoal embers along the
f
ront and sides o
f
the log support tray in a realistic manner.
Fine dust found in the bottom of the bag should not be used.
NOTE: Charcoal embers are not to be placed on the burner.
97.1
Remove the backing o
f
the logo supplied and place on the glass viewing door,
as indicated. ½"
½"
LOGO
4.5 OPTIONAL CHARCOAL EMBERS
4.6 GLOWING EMBERS
4.7 LOGO PLACEMENT

15
W415-0446 / H / 02.02.12
5.0 BLOWER REPLACEMENT
black
white
red
SPEED
CONTROL
SWITCH
BLOWER
THERMAL
SWITCH
FRONT BLOWER ACCESS COVER
THERMAL SWITCH / BRACKET
ASSEMBLY
REAR BLOWER ACCESS COVER
A. Turn off the electrical power and the gas supply to the
appliance.
B. Open the glass door and remove the logs and fibre bricks, if
installed.
C. Remove the front blower access cover held on with 4
screws.
D. Remove the rear blower access cover. NOTE: Check the
blower gasket for damage. Replace if damaged.
E. Disconnect the two blower wires. Remove the blower
from the mounting plate and replace. For thermal
switch replacement: Remove the mounting bracket
secured to the underside of the burner base. Remove
the thermal switch from the bracket and replace.
F. Reconnect the two wires. Re-install the blower
gasket. Reattach the blower mounting plate and
blower access covers. Replace the logs. Close the
fire viewing door.
G. Turn the gas supply and electricity back on. Because
the blower is thermally activated, when turned on,
it will automatically start approximately 5-15
minutes after lighting the appliance and will
run for approximately 30-45 minutes after the
appliance has been turned off. Use of the fan
increases the output of heat.
Drywall dust will penetrate into the blower
bearings causing irreparable damage and
must be prevented from coming into contact
with the blower or its compartment. Any
damage resulting from this condition is not
covered by the warranty policy.
!
WARNING
RISK OF FIRE AND ELECTRICAL SHOCK.
TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THIS APPLIANCE.
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH
THIS APPLIANCE. USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS
COMPONENTS, VENTING COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL
VOID THE WARRANTY AND CERTIFICATION.
ENSURE THAT THE FAN’S POWER CORD IS NOT IN CONTACT WITH ANY SURFACE OF THE
APPLIANCE TO PREVENT ELECTRICAL SHOCK OR FIRE DAMAGE. DO NOT RUN THE POWER
CORD BENEATH THE APPLIANCE.
THE WIRE HARNESS PROVIDED IN THE BLOWER KIT IS A UNIVERSAL HARNESS. WHEN
INSTALLED, ENSURE THAT ANY EXCESS WIRE IS CONTAINED, PREVENTING IT FROM MAKING
CONTACT WITH MOVING OR HOT OBJECTS.
51.5

16
W415-0446 / H / 02.02.12
6.0 OPERATION
Ensure that a continuous gas flow is at the burner before installing the door. When lit for the first time, the appliance will
emit an odor for a few hours. This is a normal temporary condition caused by the "burn-in" of paints and lubricants used in
the manufacturing process and will not occur again.
A
fter extended periods of non-operation such as following a vacation or a warm weather season, the appliance may emit a
slight odor for a few hours. This is caused by dust particles in the heat exchanger burning off. In both cases, open a
window to sufficiently ventilate the room.
FOR YOUR SAFETY READ BEFORE LIGHTING:
A. This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.
B. Before operating smell all around the appliance area for gas and next to the floor because some gas is heavier than
air and will settle on the floor.
C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to
repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect
the appliance and replace any part of the control system and any gas control which has been under water.
Turn off all gas to the appliance.
Open windows.
Do not try to light any appliance.
Do not touch any electric switch; do not use any
phone in your building. GAS KNOB
WARNING: The gas valve has an interlock device which will not allow the pilot burner to be lit until the thermo-
couple has cooled. Allow approximately 60 seconds for the thermocouple to cool.
When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed slightly.
1. Stop! Read the above safety information on this label.
2. Turn off all electric power to the appliance.
3. Turn the gas knob clockwise to off.
4. Wait five (5) minutes to clear out any gas. If you smell gas including near the floor. Stop! Follow "B" in the
above safety information on this label. If you don't smell gas go the next step.
5. Turn gas knob counter-clockwise to pilot.
6. Depress slightly and hold gas knob while lighting the pilot with the push button igniter. Keep knob depressed for one
minute, then release. If pilot does not continue to burn, repeat steps 3 through 5.
7. With pilot lit, depress and turn gas knob counter-clockwise to on.
8. If equipped with remote on-off switch / thermostat, main burner may not come on when you turn valve to on. Remote
switch must be in the on position to ignite burner.
9. Turn on all electric power to the appliance.
1. Turn off all electric power to the appliance if service is to be performed.
2. Push in gas control knob slightly and turn clockwise to off. Do not force.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier,
call the fire department.
WHAT TO DO IF YOU SMELL GAS:
LIGHTING INSTRUCTIONS:
TO TURN OFF GAS
TURN THE CONTROL VALVE TO THE OFF POSITION WHEN HEATER IS NOT IN USE.
47.2
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH
THE GLASS DOOR OPENED OR REMOVED.
!
WARNING

17
W415-0446 / H / 02.02.12
7.0 ADJUSTMENTS
7.1 PILOT BURNER ADJUSTMENT
Adjust the pilot screw to provide properly sized flame. Turn in a clockwise
direction to reduce the gas flow.
Inlet pressure can be checked by turning screw (A)
counter-clockwise until loosened and then placing
pressure gauge tubing over the test point. Gauge should
read 7” (minimum 4.5”) water column for natural gas or 13” (11”
minimum) water column for propane. Check that main burner is
operating on “HI”.
Outlet pressure can be checked the same as above using screw (B).
Gauge should read 3.5” water column for natural gas or 10” water
column for propane. Check that main burner is operating on “HI”.
AFTER TAKING PRESSURE READINGS, TIGHTEN SCREWS
FIRMLY TO SEAL. DO NOT OVER TORQUE. LEAK TEST.
39.3
P
I
P
I
L
O
T
N
O
L
O
T
H
I
L
O
F
F
O
A
B
PILOT SCREW
PILOT
BURNER
THERMOCOUPLE
THERMOPILE
7.2 VENTURI ADJUSTMENT
This appliance has an air shutter that has been factory set open according
to the chart below:
Regardless of venturi orientation, closing the air shutter will cause a more
yellow flame, but can lead to carboning. Opening the air shutter will cause a
more blue flame, but can cause flame lifting from the burner ports. The
flame may not appear yellow immediately; allow 15 to 30 minutes for the
final flame colour to be established.
AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED
INSTALLER!
AIR
SHUTTER
OPENING
VENTURI
BURNER
ORIFICE
49.1
CDI-30
NG 1/4”
LP 3/8”
It’s important to periodically perform a visual check of the pilot and
burner flames. Compare them to the illustrations provided. If any flames
appear abnormal call a service person.
54.2
3/8” - 1/2”
FLAME MUST
ENVELOP UPPER
3/8" TO 1/2" OF
THERMOCOUPLE &
THERMOPILE
7.3 FLAME CHARACTERISTICS

18
W415-0446 / H / 02.02.12
8.0 MAINTENANCE
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after servicing. This appliance and its venting system
should be inspected before use and at least annually by a qualified service person. The appliance area must
be kept clear and free of combustible materials, gasoline or other flammable vapors and liquids. The flow of
combustion and ventilation air must not be obstructed.
1. In order to properly clean the burner and pilot assembly, remove the logs, rocks and/or glass to
expose both assemblies.
2. Keep the control compartment, media, burner, air shutter opening and the area surrounding the logs
clean by vacuuming or brushing, at least once a year.
3. Check to see that all burner ports are burning. Clean out any of the ports which may not be burning or
are not burning properly.
4. Check to see that the pilot flame is large enough to engulf the flame sensor and/or thermocouple /
thermopile as well as reaches the burner.
5. Replace the cleaned logs, rocks or glass. Failure to properly position the media may cause carboning
which can be distributed in the surrounding living area.
6. Check to see that the main burner ignites completely on all openings when turned on. A 5 to 10
second total light-up period is satisfactory. If ignition takes longer, consult your local authorized dealer /
distributor.
7. Check that the gasketing on the sides, top and bottom of the door is not broken or missing. Replace if
necessary.
8. If for any reason the vent air intake system is disassembled, re-install and re-seal per the instructions
provided for the initial installation. 40.1
MAINTENANCE
MAINTENANCE
MAINTENANCE
TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE.
APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED.
DO NOT USE ABRASIVE CLEANERS.
!
WARNING
8.1 CARE OF GLASS
5.1
DO NOT CLEAN GLASS WHEN HOT! DO NOT USE
ABRASIVE CLEANERS TO CLEAN GLASS.
Buff lightly with a clean dry soft cloth. Clean both sides
of the glass after the first 10 hours of operation with a
recommended fireplace glass cleaner. Thereafter clean
as required. If the glass is not kept clean permanent
discoloration and / or blemishes may result.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
!
WARNING

19
W415-0446 / H / 02.02.12
8.2 DOOR GLASS REPLACEMENT
A. Place the door frame face down careful not to scratch the
paint.
B. Center the gasketed glass inside the door frame with the thick
side of the gasket facing up.
C. Bend the glass retainers located along the edge of the door
frame over the gasket holding the glass in place. Careful not
to break the glass.
!
WARNING
DO NOT USE SUBSTITUTE MATERIALS.
GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.
CARE MUST BE TAKEN WHEN REMOVING AND DISPOSING OF ANY BROKEN DOOR GLASS OR
DAMAGED COMPONENTS. BE SURE TO VACUUM UP ANY BROKEN GLASS FROM INSIDE THE
APPLIANCE BEFORE OPERATION.
DO NOT STRIKE, SLAM OR SCRATCH GLASS. DO NOT OPERATE APPLIANCE WITH GLASS
REMOVED, CRACKED, BROKEN OR SCRATCHED.
56.1A
NOTE: Care must be taken when removing and disposing of any broken glass or damaged
components. Be sure to vacuum up any broken glass from inside the appliance before operation.
GLASS
GASKET
DOOR
FRAME
GLASS
RETAINER

20
W415-0446 / H / 02.02.12
Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally
all parts can be ordered through your Authorized dealer / distributor.
FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE
REQUIRED TO HONOUR THE CLAIM.
When ordering replacement parts always give the following information:
• Model & Serial Number of appliance
• Installation date of appliance
• Part number
• Description of part
• Finish
* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMATION, CONTACT YOUR
AUTHORIZED DEALER. 41.2
FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE
ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY
DAMAGE OR PERSONAL INJURY.
** THIS IS A FAST ACTING THERMOCOUPLE. IT IS AN INTEGRAL SAFETY COMPONENT. REPLACE ONLY WITH
A FAST ACTING THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD.
!
WARNING
9.0 REPLACEMENTS
COMPONENTS
REF NO. PART NO. DESCRIPTION
1 GZ552 REPLACEMENT BLOWER
2 W725-0035 NATURAL GAS VALVE
2 W725-0026 PROPANE GAS VALVE
3 W456-0042 #42 NATURAL GAS BURNER ORIFICE
3 W456-0054 #54 PROPANE GAS BURNER ORIFICE
4 W357-0001 PIEZO IGNITER
5 W680-0004 THERMOPILE
6 W680-0005 THERMOCOUPLE**
7 W010-0801 NATURAL GAS PILOT ASSEMBLY
7 W010-0800 PROPANE GAS PILOTASSEMBLY
8* W690-0002 THERMAL SENSING SWITCH
9* W660-0009 BURNER ON/OFF SWITCH
10 W135-0183 REAR LOG
11 W135-0184 LEFT MIDDLE LOG
12 W135-0185 RIGHT MIDDLE LOG
13 W135-0186 LEFT CROSSOVER LOG
14 W135-0187 CENTER CROSSOVER LOG
15 W135-0188 RIGHT CROSSOVER LOG
16 GL-639 LOG SET
17* W361-0016 GLOWING EMBERS
18 W010-1046 BURNER ASSEMBLY
19 W455-0070 NATURAL GAS PILOT INJECTOR
19 W455-0068 PROPANE GAS PILOT INJECTOR
20* W385-0430 CONTINENTAL LOGO
21* W562-0008 GLASS GASKET
22* KB-35 VARIABLE SPEED SWITCH
23* W010-1095 GLASS W/ GASKET
24 W010-1042 DOOR, GLASS & GASKET ASSEMBLY