Cooper & Hunter CR262-RG10G User manual

IMPORTANT NOTE:
REMOTE CONTROLLER
OWNER’S MANUAL
Thank you for purchasing our air conditioner.
Please read this manual carefully before
operating your new air conditioning unit.
Make sure to save this manual for future reference.

Table of Contents
Remote Controller Specifications ......................................................02
Handling the Remote Controller ....................................................03
Buttons and Functions ...................................................................04
Remote Screen Indicators ..............................................................08
How to Use Basic Functions ..........................................................09
How to Use Advanced Functions ..................................................12
01

FIT BATTERIES
POINT REMOTE TOWARD UNIT
PRESS POWER BUTTON
SELECT MODE SELECT TEMPERATURE
SELECT FAN SPEED
1
6
2
5 4
3
AUTO
COOL
DRY
HEAT
FAN
NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections
of this manual for a detailed description of how to use your air conditioner.
SPECIAL NOTE
•Button designs on your unit may differ slightly from the example shown.
If the indoor unit does not have a particular function, pressing that function’s button on
the remote control will have no effect.
When there are wide differentces between “Remote controller Manual” and “USER’S
MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.
•
•
02
Remote Controller Specifications
Quick Start Guide
Rated Voltage
3.28 ft / 8m
3.0V( Dry batteries R03/LR03×2)
Environment
Signal Receiving Range
23°F~140°F(-5°C~60°C)

TIPS FOR USING REMOTE CONTROL
NOTES FOR USING REMOTE CONTROL
• The remote control must be used within 8
meters of the unit.
The unit will beep when remote signal is
received.
Curtains, other materials and direct sunlight
can interfere with the infrared signal receiver.
Remove batteries if the remote will not be
used more than 2 months.
•
•
•
•
•
Inserting and Replacing Batteries
Your air conditioning unit may come with two
batteries(some units). Put the batteries in the
remote control before use.
1. Slide the back cover from the remote control
downward, exposing the battery compartment.
Insert the batteries, paying attention to match
up the (+) and (-) ends of the batteries with
the symbols inside the battery compartment.
Slide the battery cover back into place.
2.
3.
BATTERY NOTES
For optimum product performance:
• Do not mix old and new batteries, or
batteries of different types.
•
Do not leave batteries in the remote control
if you don’t plan on using the device for more
than 2 months.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for proper
disposal of batteries.
The device could comply with the local national
regulations.
In Canada, it should comply with
CAN ICES-3(B)/NMB-3(B).
In USA, this device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications not approved by the
party responsible for compliance could void
user’s authority to operate the equipment.
03
Handling the Remote Controller

Buttons and Funcitons
04
SHORTCUT
SLEEP
FAN SPEED
Saves energy during sleeping
hours.
Used to restore the current
settings or resume previous
settings.
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the How to Use Basic Functions section of this manual.
ON/OFF
SET
Turns the unit on or off. MODE
OK
LED
Scrolls through operation modes
as follows:
NOTE: Please do not select
HEAT mode if the machine you
purchased is cooling only type.
Heat mode is not supported by the
cooling only appliance.
AUTO
 COOL 
DRY HEAT FAN
TIMER ON
TIMER OFF
Increases temperate in
1°F (1°C) increments.
Max. temperature is
86°F (30°C).
TEMP
TEMP
Used to confirm the selected
functions
Decreases temperature
in 1°F(1°C) increments.
Min. temperature is
60°F(16°C).
Sets timer to turn unit off
(see How to Use Basic
Functions for instructions).
Turns indoor unit’s LED display and
air conditioner buzzer on and off
(model dependent), which create a
comfortable and quiet environment.
Scrolls through operation
functions as follows:
Fresh( )
I SENSE ( )
AP mode( ) Fresh...



The selected symbol will
flash on the display area,
press the OK button to
confirm.
Sets timer to turn unit
on (see How to Use Basic
Functions for instructions).
°C/°F
The temperature display
between the °C & °F.
ENERGY SAVER
Press this button to activate the
Energy saving mode. Press it
again to stop the funtion.
AUTO LOW
MED HIGH
 

Selects fan speeds in
the following order:

05
TIMER OFF
Sets timer to turn unit off
(see How to Use Basic
Functions for instructions).
Turns indoor unit’s LED display and
air conditioner buzzer on and off
(model dependent), which create a
comfortable and quiet environment.
FAN SPEED
SLEEP
SWING
Saves energy during sleeping
hours.
Starts and stops the horizontal
louver movement.
ON/OFF
SET
Turns the unit on or off.
MODE
OK
LED
Scrolls through operation modes
as follows: AUTO
 COOL 
DRY HEAT FAN
TIMER ON
Increases temperate in
1°F (1°C) increments.
Max. temperature is
86°F (30°C).
TEMP
TEMP
Used to confirm the selected
functions
Decreases temperature
in 1°F(1°C) increments.
Min. temperature is
60°F(16°C).
Scrolls through operation
functions as follows:
Fresh( )
I SENSE ( )
AP mode( ) Fresh...



The selected symbol will
flash on the display area,
press the OK button to
confirm.
Sets timer to turn unit
on (see How to Use Basic
Functions for instructions).
°C/°F
The temperature display
between the °C & °F.
ENERGY SAVER
Press this button to activate the
Energy saving mode. Press it
again to stop the funtion.
AUTO LOW
MED HIGH
 

Selects fan speeds in
the following order:
NOTE: Please do not select
HEAT mode if the machine you
purchased is cooling only type.
Heat mode is not supported by
the cooling only appliance.

06
ON/OFF
Turns the unit on or off.
Increases temperate in
1°C increments.
Max. temperature is
30°C.
TEMP
Decreases temperature
in 1°C increments.
Min. temperature is
16°C.
AUTO LOW
MED HIGH
 

Selects fan speeds in
the following order:
SLEEP
Saves energy during sleeping
hours.
SET
MODE
OK
LED
Scrolls through operation modes
as follows:
AUTO
 COOL

DRY HEAT FAN
TIMER ON
TIMER OFF
TEMP
Used to confirm the selected
functions.
Sets timer to turn unit off
(see How to Use Basic
Functions for instructions).
Turns indoor unit’s LED display and
air conditioner buzzer on and off
(model dependent), which create a
comfortable and quiet environment.
The selected symbol will
flash on the display area,
press the OK button to
confirm.
Sets timer to turn unit
on (see How to Use Basic
Functions for instructions).
SHORTCUT
Used to restore the current
settings or resume previous
settings.
I SENSE
Press this button to activate the
I SENSE mode.
SWING
FAN SPEED
Starts and stops the horizontal
louver movement. Hold down
for 2 seconds to initiate vertical
louver auto swing feature.
NOTE: Please do not select
HEAT mode if the machine you
purchased is cooling only type.
Heat mode is not supported by
the cooling only appliance.
Scrolls through operation
functions as follows:
Fresh( ) AP mode( )
Fresh...


NOTE: Press together &
buttons at the same time
for 3 seconds will alternate
the temperature display
between the °C & °F.

07
Increases temperate in
1°F (1°C) increments.
Max. temperature is
86°F (30°C).
Decreases temperature
in 1°F(1°C) increments.
Min. temperature is
60°F(16°C).
Scrolls through operation
functions as follows:
Fresh( )
I SENSE ( )
AP mode( ) Fresh...



The selected symbol will
flash on the display area,
press the OK button to
confirm.
AUTO LOW
MED HIGH
 

Selects fan speeds in
the following order:
Turns indoor unit’s LED display and
air conditioner buzzer on and off
(model dependent), which create a
comfortable and quiet environment.
LED
°C/°F
The temperature display
between the °C & °F.
SLEEP
Saves energy during sleeping
hours.
ON/OFF
SET
Turns the unit on or off. MODE
OK
Scrolls through operation modes
as follows:
AUTO
 COOL

DRY HEAT FAN
TIMER ON
TIMER OFF
TEMP
TEMP
Used to confirm the selected
functions
Sets timer to turn unit off
(see How to Use Basic
Functions for instructions).
Sets timer to turn unit
on (see How to Use Basic
Functions for instructions).
SHORTCUT
Used to restore the current
settings or resume previous
settings.
SWING
FAN SPEED
Starts and stops the horizontal
louver movement. Hold down
for 2 seconds to initiate vertical
louver auto swing feature.
NOTE: Please do not select
HEAT mode if the machine you
purchased is cooling only type.
Heat mode is not supported by
the cooling only appliance.

Information are displayed when the remote controller is power up.
Transmission Indicator
MODE display
TIMER ON display
FAN SPEED display
TIMER OFF display
LOCK display
Not available for
this unit
Temperature/Timer/Fan speed
display
Fresh feature display
Sleep mode display
I Sence feature display
Wireless control feature display
Low battery detection display
(If flashes)
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actaul
operation, only the relative function signs are shown on the display window.
08
Remote Screen Indicators
Displays when LOCK feature
is activated.
Lights up when remote
sends signal to indoor
unit Displays the current
including:
mode,
Displays the set temperature
by default, or fan speed or
timer setting when using
TIMER ON/OFF functions.
Temperature range:
oo
16-30 C/60-86 F
Timer setting range:
0-24 hours
This display is blank when
operating in FAN mode.
Horizontal louver auto
swing display
LOW
MED
HIGH
AUTO
Displays selected fan speed:
This fan speed can not be
adjusted in AUTO or DRY
mode.

09
How to Use Basic Functions
ATTENTION! Before operation, please
ensure the unit is plugged in and power
is available.
AUTO Mode
SETTING TEMPERATURE
The operating temperature range for units
is 60-86°F (16-30°C).
You can increase or decrease the set
temperature in 1°F (1°C) increments.
In AUTO mode, the unit will automatically select
the COOL, FAN, or HEAT function based on
the set temperature.
1. Press the MODE button to select AUTO.
2. Set your desired temperature using the TEMP
or TEMP button.
3. Press the ON/OFF button to start the unit.
NOTE: FAN SPEED can’t be set in AUTO
mode.
COOL ModeBasic operation
1
3
2
4
Set your desired temperature using the
TEMP or TEMP button.
Press the ON/OFF button to start the unit.
1. Press the MODE button to select COOL
mode.
2.
3. Press FAN button to select the fan speed:
AUTO, LOW, MED, HIGH .
4.
1
3
2

10
1. Press the MODE button to select DRY.
2. Set your desired temperature using the TEMP
or TEMP button.
3. Press the ON/OFF button to start the unit. Set your desired temperature using the
TEMP or TEMP button.
Press the ON/OFF button to start the unit.
1. Press the MODE button to select HEAT
mode.
2.
3.
Press FAN button to select the fan speed:
AUTO, LOW, MED, HIGH.
4.
DRY Mode (dehumidifying)
NOTE: FAN SPEED cannot be changed in
DRY mode.
HEAT Mode
NOTE: As outdoor temperature drops, the
performance of your unit’s HEAT function
may be affected. In such instances, we
recommend using this air conditioner in
conjunction with other heating appliances.
Press the MODE button to select FAN mode.
Press the ON/OFF button to start the unit.
Press FAN button to select the fan speed:
AUTO, LOW, MED, HIGH .
FAN Mode
1.
2.
3.
NOTE:You can’t set temperature in FAN mode.
As a result, your remote control’s LCD screen
will not display temperature.
1
3
2
4
1
2
3
1
3
2

11
Setting the TIMER
TIMER ON setting
TIMER OFF setting
TIMER ON & OFF setting(example)
TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.
Press TIMER ON button to
initiate the ON time sequence.
Press up or down button for
multiple times to set the desired
time to turn on the unit.
Point remote to unit and wait
1sec, the TIMER ON will be
activated.
x5 1sec
Press Temp. up or down button for
multiple times to set the desired
time to turn off the unit.
Press TIMER OFF button to
initiate the OFF time sequence.
Point remote to unit and wait
1sec, the TIMER OFF will be
activated.
1sec
x10
NOTE:
1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments
with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour
increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer
will revert to 0.0 after 24.
2. Cancel either function by setting its timer to 0.0h.
Current
time 1PM 2:00PM 3:00PM 4PM 5PM 6PM
Timer starts Unit turns
ON
Unit turns
OFF
2.5 hours later
5 hours later
3:30PM
Example: If current timer is
1:00PM, to set the timer as above
steps, the unit will turn on 2.5h
later (3:30PM) and turn off at
6:00PM.
Keep in mind that the time periods you set for both functions refer to hours after the current
time.
xn xnxn

12
How to Use Advanced Functions
Press Swing button
The horizontal louver will swing up and down
automatically when pressing Swing button.
Press again to make it stop.
Swing function
ENERGY SAVER function(some models)
Press Energy saver button to turn on this
function.
This function is available on COOL, DRY,
AUTO modes.
Press SHORTCUT button
Push this button when remote controller is on,
the system will automatically revert back to
the previous settings including operating
mode, setting temperature, fan speed level
and sleep feature (if activated).
If pushing more than 2 seconds, the system
will automatically restore the current operation
settings including operating mode, setting
temperature, fan speed level and sleep feature
(if activated ).
SHORTCUT function (some models)
Press this button will alternate the temperature
display between the °C & °F.
°C/°F (some models)

13
The SLEEP function is used to decrease energy
while you sleep(and don’t need the same
temperature settings to stay comfortable). This
function can only by activated via remote control.
Note: The SLEEP function is not available in
FAN or DRY mode.
For the details, please see “sleep operation ” in
“ USER’S MANUAL ”.
Press SLEEP button
LED DISPLAY
Press this button to turn on and turn off the
display on the indoor unit.
Press LED button
SLEEP Function
LOCK function
5s
5s
+
Press together LED button and °C/°F button
(iSense button on some models) at the same time
more than 5 seconds to activate Lock function.
All buttons will not response except pressing
these two buttons for two seconds again to
disable locking.
5s
iSense
or

Fresh ( ) I SENSE ( ) AP mode( )
[ ]: If your remote controller has I SENSE button, you can not use the SET button to
select I SENSE feature.
14
or
FRESH function ( ) (some units) :
I SENSE function ( ) :
SET function
Press the SET button to enter the function setting, then press SET button or TEMP or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:

*
*
The I SENSE function enables the remote control to measure the temperature at its current location
and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT
modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself)
will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
When the FRESH function is initiated, the Ionizer/Plasma Dust Collector(depending
on models) is energized and will help to remove pollen and impurities from the air
AP function ( ) (some units) :
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing
the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.