Cooper Security 95EN User manual

MANAGER’S MANUAL
HARDWIRED
CONTROL PANELS

2
Contents
Preface .............................................................................................. 3
Introduction .................................................................................................. 3
Accessing the User Menu ............................................................................ 4
Options in the User Menu ................................................................ 5
Option 1: Omitting Zones........................................................................... 5
Option 2: Shunting 24hr Zones.................................................................. 6
Option 3: Setting System Options.............................................................. 7
Option 4: Testing the System .................................................................. 13
Option 5: Using the Engineer Tools......................................................... 17
Option 6: Setting the Time and Date ....................................................... 19
Option 7: Customising Text ..................................................................... 20
Option 8: Setting Up Users...................................................................... 22
Option 9: Using the Log........................................................................... 31
Text Keys ........................................................................................ 35
Zone Numbering............................................................................. 36
Telecommands and PA Transmitters............................................ 37
Telecommand Numbering.......................................................................... 37
Telecommand Buttons ............................................................................... 37
PA Buttons ................................................................................................. 38
Log Events ...................................................................................... 39
System Records ............................................................................. 44
General System Details ............................................................................. 44
User Details ............................................................................................... 46
Zone Details............................................................................................... 47
Telecommand Details ................................................................................ 48
Service Record .......................................................................................... 49
Installer Information ................................................................................... 50
Quick Reference ............................................................................. 51
© Cooper Security Limited 2007
Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor
Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly
by this book. The contents of this book are subject to change without notice.
Cooper Security Limited make every possible effort to update manuals and guides regularly to reflect changes in the
product. If this document does not reflect the function of the product please let us know. You may be able to
download a more recent version of the document from our website:
www.coopersecurity.co.uk
All trademarks acknowledged.
Printed and published in the UK
Part No: 11773727

3
Preface
Introduction
About your Alarm
System
Your intruder alarm comprises several
components, such as keypads and sensors,
linked to a control unit, which is concealed
from view but accessible for maintenance.
There are three versions of the control unit:
the 95EN, 85EN and the 65EN. The 95EN
can have up to eight partitions, while the
85EN and 65EN can have up to four
partitions. Ask you’re alarm company which
one you have.
About this Manual This manual describes the functions
available from the user menu. The manual is
intended for those people responsible for
carrying out tasks such as adding new user
codes, viewing the log and omitting zones
from the setting procedure. Note that some
of the procedures described on pages 30 to
34 are slightly different for the three control
units.
Other Manuals Please refer to the User's Guide for details
of how to set, unset and reset your alarm
system.
The Engineering Manual (available only to
installation engineers) describes how to set
up the system.
Making Changes To ensure problem-free operation, discuss
the system with your alarm company before
making significant changes. It is good
practice to maintain a paper record of how
the system is set up, using the record sheets
at the back of this manual.

4
Accessing the User Menu
To access the user menu:
BANNER TEXT
17:30 Sun 01 JAN
1. Enter your user code or present your
proximity tag.
Set Partition?
Ptns > ***.....
2. Press .
User Menu
1: Omit Zones
The first option, Omit Zones, is displayed.
Z
Access to options depends on user type
(page 23).
Selecting Options You can select options in two ways:
1. Press |and ¬until the required option
is displayed, then [.
2. Press a numeric "hot" key (0to 9),
e.g. press 1to display Omit Zones, then
[to select the option.
Exiting from the User
Menus
To return the system to its normal operating
state, press ]to step back through the
menus until the time and date are displayed.
Four / Six digit User
Codes
Normally the system accepts user codes that
are four digits long. For added security the
installer may have programmed the system
accept six digit user codes1.
When first installed the default user code for the system manager is
1234 (123400 if using six digit codes). Please remember to change this
user code to something more secure as soon as possible.
1Option 47 in Engineer menu.

5
Options in the User Menu
Option 1: Omitting Zones
Sometimes you may need to omit zones
when you set your system, e.g. if a zone is to
remain occupied while the rest of the system
is set. This option enables you to select
which zones to omit.
Z
When the system is unset, any selections
made here are cleared. This prevents
zones from being omitted inadvertently.
Z
You can omit only zones that have been
set up as omittable (Engineer option 11).
User Menu
1:Omit Zones 1. Press [to select Omit Zones.
0001 is Armed 2. Select the zone to omit by using |or ¬,
or by entering the four-digit zone number.
Refer to page 36 for details of zone
numbering.
0002 is Armed 3. Press
rto change the omit status of the
zone ("Omitted" indicates that the zone
will be omitted).
4. Press [to view the next zone, or ]to
exit.

6
Option 2: Shunting 24hr Zones
This option enables you to shunt (disable) all
24 Hour zones in selected partitions that
have been set up as shuntable in Engineer
option 11. Shunting disables a zone and the
shuntable attribute identifies whether this is
permissible.
Z
Zones remain shunted until you use the
Reinstate 24hr option (see below).
Z
Reinstating zones may start the exit
timer, depending on whether Unshunt,
No Exit or Unshunt & Exit is selected
(Engineer option 45).
User Menu
2:Shunt 24hr Zns 1. Press
[to select Shunt 24hr Zns.
1=Shunt 24Hr
2=Reinstate 24hr 2. Press 1to shunt zones or 2to
reinstate zones that have been previously
shunted.
Shunt partitions
Ptns > 1*......
3. Use the numeric keys to select the
partitions to shunt/reinstate, then press
[. Any partition numbers shown will be
shunted/reinstated. (A “*” indicates that
the partition will not be
shunted/reinstated, and “.” indicates that
you have no access to the partition.)

7
Option 3: Setting System Options
Option 3-1:
Enabling Chimes
This option enables you to select which of
your partitions (if any) use the chime feature.
In a partition with this feature enabled, zones
that have a Chime Tone attribute (Engineer
option 11) and are in a selected partition will
generate a chime tone when activated. The
partitions then remain chime-enabled until
you deselect them with this option.
A zone may generate a single, double or
triple chime, depending on the Chime Tone
attribute selected in Engineer option 11.
The chime occurs only at keypads and
extension loudspeakers assigned to the
same partition(s) as the zone.
When a chime occurs, keypads display the
zone number if configured by the Chime
Visible setting in Engineer option 45-08.
User Menu
3:System Options 1. Press [to select System Options.
System Options 1
Enable Chime 2. Press
[to select Enable Chime.
Chime On Prtns:
Ptns > 1*......
3. Use the numeric keys to select the
partitions you want to have chime
enabled, then press [. Any partition
numbers shown will be chime enabled. (A
“*” indicates that the partition will not be
chime enabled, and “.” indicates that you
have no access to the partition.)

8
Option 3-2: Setting
the Speaker Volume
This option enables you to adjust the volume
level of the extension loudspeaker
connected to the control unit.
User Menu
3:System Options 1. Press [to select this option.
System Options 2
Adjust Volume 2. Use
|or ¬, or press 2to select
Adjust Volume, then press [.
Adjust Volume
>>>>>>> (MAX) 3. Press
|and ¬, or enter a value (0 to
7), to adjust the volume, from ‘Off’ up to
maximum.
4. Press
[to accept the displayed value
or ]to exit without change.
Option 3-3: Setting
Up Time Switches
This option enables you to define up to three
time switches, which can be used to switch
outputs of the alarm system on or off at
selected times. The outputs may, for
example, control internal or external lighting
or other electrical equipment.
You can define each time switch to have up
to three pairs of switch on/off times. You can
also choose the days of the week that each
of these operate.
The outputs controlled by the time switches
are specified in Engineer option 30.
User Menu
3:System Options 1. Press [to select System Options.
System Options 3
Time Switches 2. Use
|or ¬, or press 3to select Time
Switches, then press [.

9
Time Switch 1
3. Use |or ¬, or press a hot key (e.g. 4)
to select the time switch to edit, then
press [.
Time Switch 1
On (1) 00:00 4. Use |or ¬, or press a hot key (1to
9) to select the on/off time or days of
operation to edit, then press [.
Each time switch has three pairs of
switch on/off times. For each of these,
you will notice that there is an option to
specify the on time, one to specify the
off time and another to specify the days
of operation.
Z
You can manually override a time
switch by pressing 0, then pressing r
to toggle its current status.
Time Switch 1
On (1) >00:00
5. You will see a screen similar to the one
shown opposite if you have chosen to
edit an on/off time. The number in
brackets indicates whether it is in the
first, second or third pair of on/off times.
Enter the time in 24-hour format, (e.g.
2100 for 9:00pm), then press [.
Continue from step 4 or press ]to exit.
1 Operates On :-
> ..............
6. You will see a screen similar to the one
shown opposite if you have chosen to
edit the days of operation. The number
in the top-left corner indicates whether it
is associated with the first, second or
third pair of on/off times.

10
Press 1to 7to toggle days on/off,
then press [. Continue from step 4 or
press ]to exit.
Option 3-4: Setting
Up Auto-Set Timers
Use this option to make the control unit set
or unset selected partitions at specified
times. The control unit has three auto-set
timers. You can allocate each timer to one or
more partitions, which the control unit sets
and unsets at the times you chose.
For each auto-set timer you can specify up
to three events. Each event comprises a
switch on (set) time, an off (unset) time, and
a day of the week.
When a timer reaches the “on” time for an
event the control unit operates the keypad
sounders for one minute and then sets the
allocated partition(s). Note that the control
unit will not set any partition where there is
an active detector.
During the one minute warning a user can
defer setting for a short period by entering
their user code1.
When a timer reaches an “off” time, the
control unit unsets the allocated partition(s).
User Menu
3:System Options 1. Press
[to select this option.
1Engineer menu 44 option 16 specifies the length of the defer time.

11
System Options 4
Auto Sets 2. Use |or ¬, or press 4to select Auto
Sets, then press [.
Auto Set 1
3. Use |or ¬, or press a hot key (1to
3) to select the auto-set timer to edit,
then press [. (The display shows the
timer number at the top right.)
Auto Set 1
On (1) 00:00
Each auto-set timer has three events.
The display shows the event number in
brackets on the bottom left. For each
event, you can specify the on (set) time,
the off (unset) time and the days of
operation.
4. To select the on/off time or days of
operation to edit,
EITHER
Use |or ¬then press [.
OR
Press a hot key (1to 9) then press
[.
The table below shows the hot keys for
each item:
Event 123
ON 123
OFF 456
Days 789
Auto Set 1
On (1) >00:00
5. When editing times, enter the time in 24-
hour format, (e.g. 2100 for
9:00pm), then press [.

12
1 Operates On :-
> .............. When editing the days press 1to 7to
toggle days on/off, then press [.
On the days screen the event number is
in the top-left corner. (Note that day
1=Sunday.)
6. Repeat steps 4 and 5 for each event you
wish to program.
Auto Set 1
Ptns > **
7. To allocate partitions to the auto-set
timer press r.
Use the numeric keys to select the
partitions then press [. The control unit
allocates any partition numbers shown
on the bottom line to the auto-set timer
shown on the top line. (A “*” indicates
that the partition will not be allocated,
and “.” Indicates that you have no
access to the partition.)
8. Repeat steps 3 to 7 for all the auto-set
timers you wish to edit, or press ]to
exit.
Z
You can stop or restart an auto-set
timer at any time, whether the timer has
set the system or not.
a) Enter User Menu 3-4.
b) Select the auto-set timer you wish to
stop.
c) Press 0, then rto toggle the
timer’s current status.
If the timer has set a partition, then
when you toggle the timer off, the
control unit will unset that partition.

13
Option 4: Testing the System
Option 4-1:
Performing a Walk
Test
This option enables you to check that zones
are operating correctly. You can test only
those partitions that you have access to.
Each zone tested is added (once) to the
event log, which you can review using User
option 9-1 (page 31).
User Menu
4:Test Options 1. Press [to select this option.
Test Options 1
Walk Test 2. Press
[to select Walk Test.
Walk Test
Ptns > 1*......
3. Use the numeric keys to select the
partitions to test, then press [. Any
partition numbers shown will be tested.
(A “*” indicates that the partition will not
be tested, and “.” indicates that you have
no access to the partition.
Esc To Stop Test
& View Zones
4. Walk through your partitions and operate
all detection devices.
0003 Active
As you activate each zone, the internal
sounders will emit a chime tone and the
display will identify the activated zone.
5. When you have finished the test, press
].
Panel Zone 1
0001 Healthy
6. The status of the lowest zone number
tested is displayed. Press [to view the
next lowest zone tested.
7. Press
]to exit.

14
Option 4-2: Testing
the Bell
This option enables you to test the internal
sounder, strobe and external sounder.
User Menu
4:Test Options 1. Press [to select this option.
Test Options 2
Bell Test 2. Use
|or ¬, or press 2to select Bell
Test, then press [.
Bell Test
Ptns > 12......
3. Use the numeric keys to select the
partitions to test, then press [. Any
partition numbers shown will be tested.
(A “*” indicates that the partition will not
be tested, and “.” indicates that you have
no access to the partition.)
Bell Test 1
Bell Only
4. The external sounder should activate.
Press [to carry out the next test.
Bell Test 2
Bell & Strobe ON
5. The external sounder and strobe should
be active. Press [to carry out the next
test.
Bell Test 3
Strobe Only
6. Only the strobe should be active. Press
[to carry out the next test.
Bell Test 4
Alarm Sounder On
7. The internal sounder should activate.
Press [to carry out the next test.
Bell Test 0
Bell/Strobe OFF
8. The sounders and strobe should switch
off. Press [to repeat the tests, or ]to
exit.

15
Option 4-3:
Telecommand
Batteries
This option enables you to check if any
telecommands have reported a low battery.
User Menu
4:Test Options 1. Press [to select this option.
Test Options 3
Telecmd Batts 2. Use
|or ¬, or press 3to select
Telecommand Batts, then press [.
No batteries low
Either:
The display shows that all telecommands
are OK.
2:01:01 Batt Low
Martha’s
OR
The display shows the number of any
telecommands that have reported a low
battery. If you have programmed a text
name for the telecommand, the display
shows that text on the bottom line.
3. Press
[to repeat the tests, or ]to
exit.

16
Option 4-4:
Telecommand Test
This option enables you to test a
telecommand, or identify an unknown
telecommand.
User Menu
4:Test Options 1. Press [to select this option.
Test Options 4
Telecmd Test 2. Use
|or ¬, or press 4to select
Telecmd Test, then press [.
2:01:1 RNode
Martha’s
3. Either:
Use |or ¬to select the telecommand
you want to test, and press [.
OR:
Press any button on the telecommand
you are testing and press [.
2:01:3 RNode
9(5) Bat-H
The top line of the display shows the
number of the telecommand you are
testing. The bottom line of the display
shows (from left to right):
Current signal strength.
Previous lowest signal strength in
brackets.
”Bat-” (for Battery) followed by H for
healthy or L for low.
4. Either:
Press ]to exit, leaving the record of
lowest signal strength as it is.
OR:
Press [to exit, resetting the record of
lowest signal strength to the current
signal strength, ready to record a new
value.

17
Option 5: Using the Engineer Tools
Option 5-1:
Configuring Engineer
Access
This option enables you to define a period
during which an engineer can log into the
alarm system. Once the period has expired,
the engineer can continue working if logged
in but will not be able to log in again.
The period starts from the time you set it and
can be four hours or five minutes. You can
terminate the period at any point.
Z
The default setting is Infinite.
User Menu
5:Engineer Tools 1. Press [to select this option.
Engineer Tools 1
Engineer Access 2. Press
[to select Engineer Access.
3. Use
|or ¬, or press a hot key (1to
4), to select the required option, then
press [.
If you select 4 Hour Window or 5 Min
Window, the engineer will be able to log
in at any time within a 4-hour/5-minute
period from now.
Selecting Infinite allows the engineer
access at any time.
Selecting Close Window terminates any
period currently running.

18
Option 5-2: Starting
a Call Back
You can use this option to initiate a
connection over the telephone line to a
remote site that is running the Downloader
software. Once the communication link is
established, the remote site can upload data
and change settings in the control panel.
The link continues until the remote site
disconnects it.
Z
Select this option only if requested by
your alarm company.
Z
Your alarm company may be able to
initiate the link, depending on the
Access Mode (Engineer option 51-3).
User Menu
5:Engineer Tools 1. Press
[to select this option.
Engineer Tools 2
Call Service? 2. Use |or ¬, or press 2to select Call
Service?, then press [.
Start CallBack 1
3. Use |or ¬, or press a hot key (1to
4) to select the number to call (as
defined in Engineer option 51-4), then
press [to begin the call.
Calling On : 1
Hit ESC to abort
4. If the connection is established
successfully, the system automatically
returns to its original state. If the
connection is not established
successfully, press ]to abandon the
call.

19
Option 6: Setting the Time and Date
Option 6-1: Setting
the Time
This option enables you to set the system
time.
Z
The system automatically
advances/retards the time by one hour
at 2am on the standard summer/winter
changeover dates.
User Menu
6:Time And Date 1. Press [to select this option.
Time and Date 1
Set Time 2. Press
[to select Set Time.
Enter new time:-
11:44
3. To change the time, enter four digits
(hhmm) for the current time, e.g. 1810
for 6:10pm.
4. Press
[to accept the displayed time,
or ]to exit without saving.
Option 6-2: Setting
the Date
This option enables you to set the system
date.
User Menu
6:Time And Date 1. Press [to select this option.
Time And Date 2
Set Date 2. Use
|or ¬, or press 2to select Set
Date, then press [.
Current Date :-
01/01/06
3. To change the date, enter six digits
(ddmmyy) for the current date, e.g.
181006 for 18th October 2006.
4. Press [to accept the displayed
date/time, or ]to exit without saving.

20
Option 7: Customising Text
Option 7-1: Editing
the Zone Text
This option enables you to edit the text
displayed to identify zones to users.
User Menu
7:Custom Text 1. Press
[to select this option.
Custom Text 1
Zone Text 2. Press
[to select Zone Text.
Zone 0001 3. Use
|or ¬, or press a hot key to select
the zone name to edit, then press [.
^one 0001
4. Use the text editing keys (page 35) to
change the text if required. Press [to
accept the displayed text or ]to exit
without change.
Option 7-2: Editing
the Partition Text
This option enables you to edit the text
displayed to identify partitions to users.
User Menu
7:Custom Text 1. Press
[to select this option.
Custom Text 2
Prtn Text 2. Use |or ¬, or press 2to select Prtn
Text, then press [.
Viewing Prtn 1 3. Use
|or ¬, or press a hot key to select
the partition name to edit, then press [.
^iewing Prtn 1
4. Use the text editing keys (page 35) to
change the text if required. Press [to
accept the displayed text or ]to exit
without change.