NewMar SilverLeaf RV-C Control System Installation guide

2012
Newmar Corporation
October 2011
SilverLeaf RV-C Control System
Training Manual

Page 1
Newmar SilverLeaf RV-C Control System Operation/Set-UP Manual
SCREEN ACCESS
Please be aware that not all of the following screens are available to
the end user!
Some configuration screens require a password for access. Password
protected screens contain control settings that should only be
changed by qualified individuals! Changing these control settings to
an improper setting can adversely affect the operation of the control
system and may cause damage to the coach!
The following is a list of the control and system status screens available on the Newmar
SilverLeaf Control System Touch Screen Display.
SYSTEM SPLASH SCREEN
The Splash Screen is displayed momentarily on
system power up. This screen can also be
selected for display as one of the screen saver
selections found in the monitor configuration.

Page 2
HOME SCREEN
Every control function can be accessed by
pressing one of the Buttons on the Home
Screen. The Home Screen also displays system
status and warnings in order of priority. The
following items are displayed and/or controlled
from this screen:
HOME SCREEN WITH FLOOR HEAT OPTION
BUTTON FUNCTIONS
Home Button –Pressing this Button returns
you to the Home screen from the other
control screens. The Home Button is not
highlighted and is only operational from the
other screens.
AC Power Button –Pressing this Button
selects the AC Power Screen. (see AC Power
Screen)
DC Power Button –Pressing this Button
selects the DC Power Screen. (see DC Power
Screen)
Genset Button –Pressing this button selects
the Genset Screen. (see Genset Screen)
Water Button –Pressing this button selects
the Water Control Screen. (see Water
Control Screen)
Climate Button –Pressing this button
selects the Climate Control Screens. (see
Climate Control Screen)
Temp Button (Standard Control) Pressing
the Temp Button selects a screen that
displays the outside ambient temperature.
(see Temp Screen)
Floor Button (Floor Heat Option) When the
Floor Heat option is installed, the Floor
Button will be displayed in place of the
Temp Button. Pressing the Floor Button
selects the Floor Heat Control Screen. This
button is only displayed if the control
system is configured for floor heat. (see
Floor Heat Control Screen)
Features Button –Pressing this button will
select the Features Screens. (see Features
Screens)

Page 3
Genset Button (Top Center) –Pressing this
button will manually start and stop the
generator. The button indicator is
highlighted when the generator is running.
This button works the same as the Dash and
other remote switches.
AUTOFILL Button –Pressing this button will
turn on the Auto Fill feature. The button
indicator is highlighted when the Auto Fill is
on.
PUMP Button –pressing this button will
turn the Water Pump on and off. The
button indicator is highlighted when the
pump is powered.
AUTOGEN Button –Pressing this button will
select the AGS screens. The button indicator
is highlighted when the Auto Charger is
enabled. (see AGS Screens below)
Block Heater Button –Pressing this button
toggles the Block Heater relay on/off. The
button indicator is highlighted yellow when
the load is being shed and blue when on.
STATUS DISPLAYS
Overall System Status - “OK” if no errors or
warnings are present.
Warnings and Errors will be displayed in this
area in order of priority.
Date/Outside Temperature/Time –The
system date, outside temperature and time
are displayed in this area.
Tank Status –The Fresh, and Holding tanks
status is displayed as a percentage of “Full”.
Both a bar graph representation and a
numerical percentage are displayed.
DC Voltage –Both the House Battery
voltage and the Chassis Battery Voltage are
displayed. There is also a Lightning Bolt icon
that will illuminate when the isolator relay
(Charge Bridge) is energized and connecting
both battery systems together.
AC Power Source, Voltage and Current –The
AC Power Source
(Shore/Generator/Inverter), as well as, the
Voltage and Current (Amperage) for both
AC power legs are displayed.

Page 4
AC POWER SCREENS MAIN AC POWER SCREEN
The AC Power Screen displays the AC Power
Source, Line Voltage and Current (Amperage)
usage, as well as, the AC Line Frequency (Hz).
The Ac Power Source is displayed for Shore
Power; Generator or Inverter Power. The AC
Amperage values are displayed both numeri-
cally and with horizontal bar graphs. The AC
Voltage values are displayed numerically. The
AC Line Frequency is displayed in Hertz (Hz).
This screen also displays the maximum charge
draw amps setting value, as well as, the inverter
status. The Load Shed Management screen is
selected from the Load Shed Button located on
this screen. The Inverter can also be turned on
and off from this screen, via the blank button to
the right of the Inverter Status display.
AC POWER SCREENS LOAD (SHED) MANAGEMENT SCREEN
The Load Management Screen displays the
Shore Power Phase setting (Single Phase 30
Amps and less Service, Dual Phase 50 Amp
Service) and allows you to change between the
phase selections using the Change Button. The
current Amp draw is displayed for both legs on
this screen. The Load Status screen is selected
from the Loads Button. The Load Settings
Screen is selected from the Settings Button.
AC POWER SCREENS LOAD STATUS SCREEN
The Load Status Screen displays the electrical
Shed status of all the AC powered devices that
are controlled by the control system. This
screen also displays the AC voltage and
amperage usage for both power legs

Page 5
AC POWER SCREENS LOAD SETTING SCREEN 1
The first Load Setting screen configures the
following settings:
Phase Detection Manual / Automatic
Set to Manual for standard Transfer Switch.
Set to Automatic for RV-C Transfer Switch.
A RV-C Transfer Switch has the capability of
automatically detecting Dual Phase (240 VAC)
50 Amp AC power based on the available AC
power source.
Default Phase Single
Phase / Dual Phase
Selects the default Phase setting for the Load
Shedding function.
Capacity - Single Phase
(Amperage)
This setting sets the Load Shedding Amperage
value for the Single Phase selection.
Capacity Dual Phase (Amperage)
This setting sets the Load Shedding Amperage
value for the Dual Phase selection. This
should normally be set 50 Amps.
AC POWER SCREENS LOAD SETTING SCREEN 2
The second Load Setting screen configures the
following settings:
Capacity - Dual Phase
(Amperage)
This setting sets the Load Shedding Amperage
value for the Dual Phase selection. This
should normally be set 50 Amps.
Load Shedding Enabled / Disabled
Load Shedding Enabled allows the control
system to shed (turn off) system configured
AC powered devices in order to maintain a
maximum phase capacity AC amperage usage.
Generator Settling Enabled / Disabled
This setting should be set to Enabled for
proper Auto Gen operation.
Charger 1 Shedding Enabled / Disabled
This setting determines if the Battery Charger
should be shed (turned off) with the other
Load Shedding devices.

Page 6
DC POWER SCREENS MAIN DC POWER SCREEN
The Main DC Power Screen displays the Inverter
/ Charger status and allows access to the
Magnum Setting Screens
The Battery Icon has a vertical bar graph that
indicates the battery charge level. The battery
voltage value is displayed directly below the
icon. The arrows between the Battery and
Inverter Icons indicate the direction of the DC
current flow. The DC current (amperage) value
is displayed below the arrows. The Inverter/
Charger status is displayed inside the Inverter
Icon.
DC POWER SCREENS MAGNUM SETTINGS SCREEN 1
The first Magnum Setting screen configures the
following settings:
Inverter Status On / Off / Standby
Charger Status On / Off /
Standby
Max Charging Current
( Amperage)
This is the maximum amount of current the
charger can output.
Load Sense Power
( Wattage)
This is the Power Level (Search Watts Setting)
required to activate (wake up) the inverter.
DC POWER SCREENS MAGNUM SETTINGS SCREEN 2
The second Magnum Setting screen configures
the following settings:
Charger Status On / Off /
Standby
Max Charging Current
( Amperage)
This is the maximum amount of current the
charger can output.
Load Sense Power
( Wattage)
This is the Power Level (Search Watts Setting)
required to active (wake up) the inverter.
Max Charger Rate (Percentage)
This is the maximum % of AC current
(amperage) used to recharge the batteries.

Page 7
DC POWER SCREENS MAGNUM STATUS SCREEN
The DC Power (Settings) Magnum Status Screen
displays the following Status Values:
Magnum Model/Version
This value is read from the inverter via the
Inverter Module.
Battery Temperature
This value is read from the inverter battery
temperature sensor via the Inverter Module.
Internal Temperature
This value is read from the inverter via the
inverter Module.
FET Temperature
This value is read from the inverter via the
Inverter Module.
DC POWER SCREENS MAGNUM ADVANCED SETTINGS SCREEN ACCESS
The Password Access Screen is displayed to
provide access to advanced system
configuration screens. The advanced
configuration screens contain control settings
that should only be changed by qualified
individuals. Changing these control settings to
an improper setting can adversely affect the
operation of the control system and may cause
damage to the coach.
DC POWER SCREENS MAGNUM ADVANCED SETTINGS SCREEN 1
The Magnum Advanced Settings Screen has the
following Configuration Values:
Low Voltage Shutdown ( DC Voltage)
This setting is the low DC Voltage trigger point
that will turn off the Inverter.
Battery TypeFlooded / Gel /
AGM / AGM2
This should be set to match the physical
battery type.
Battery Rating (AH)
This should be set to match total house
battery power capacity
Equalization Volts ( DC Voltage)
This setting should match the manufacturer
setting for the battery type.

Page 8
DC POWER SCREENS MAGNUM ADVANCED SETTINGS SCREEN 2
The Magnum Advanced Settings Screen has the
following Configuration Values:
Low AC Volts ( AC Voltage)
This setting is the low AC Voltage (Brown Out)
trigger point that will turn off the charger and
turn the inverter on.
Absorption Volts (DC Voltage)
This is the DC Voltage that will be output
when the charger is in Absorption Mode.
Absorption Time (Hr)
This is the amount of time that the charger
will stay in Absorption Mode.
Float Volts (DC Voltage)
This is the DC Voltage that will be output
when the charger is in Float Mode.
GENSET SCREEN
The Genset Screen displays the current
Generator Status and control system run time.
Note: The system generator run time can be set
to match the physical generator hour meter
using the OnmiScope Service Tool.
The Start and Stop Buttons allow you to
manually start and stop the generator. The
Clear AGS Button allows you to clear the AGS
Safety Lockout flag to reset the Auto Gen
function.

Page 9
WATER SCREEN ALL ELECTRIC EQUIPPED COACH
The Water Screen on coaches equipped with
the All Electric option displays the Fresh and
Holding Tanks volume % full status. This screen
also displays tank related faults, if any. The
Water Pump Button turns the Water Pump on
and off. The Auto Fill Button turns the Auto Fill
function on and off.
WATER SCREEN LP EQUIPPED COACH
The Water Screen for a coach equipped with an
LP tank, displays and controls the same
functions as the All Electric Water Screen with
the addition of the LP tank % full status.

Page 10
CLIMATE SCREENS CLIMATE ALL SCREEN
The Climate Screens are used to display the
status and control the HVAC system. The
Climate “All”Screen displays and provides
global control of the Heating and Cooling for all
of the HVAC zones.
Pressing the Heat or Cool Button activates all of
the zones for the selected function at one time.
The set points can be changed by pressing the
associated up and down arrows or by dragging
the associated circular temperature wheel to
the desired set point.
The Heat or Cool Buttons will highlight and
Icons will be displayed when the functions are
active.
The Oasis control screen is only accessed from
this screen.
The Leave function is also accessed from this
screen. The Leave function allows you to set
different temperature set-points to control the
HVAC system when you leave the coach.
CLIMATE LVRM SCREEN
The Climate “LvRm”Screen displays the Heating
and Cooling controls for Living Room zone. The
Air Conditioner for cooling and both the Heat
Pump and Oasis heating systems for the Living
Room are controlled from this page.
CLIMATE KITCH SCREEN
The Climate “Kitch”Screen displays the Heating
and Cooling controls for Kitchen zone. The Air
Conditioner for cooling and only the Heat Pump
for heating are controlled from the page. There
is no Oasis heat available in this zone.

Page 11
CLIMATE BATH SCREEN
The Climate “Bath”Screen only controls the
Bathroom Oasis heating system. There is no Air
Conditioner or Heat Pump available for this
zone, therefore the Cool Button is not displayed
on this screen.
CLIMATE BED SCREEN
The Climate “Bed”Screen displays the Heating
and Cooling controls for Bedroom zone. The Air
Conditioner for cooling and both the Heat Pump
and Oasis heating systems for the Bedroom are
controlled from this page
CLIMATE OASIS SCREEN
The Oasis Screen is accessed from the Oasis
Button displayed in the Climate All Screen. This
screen controls the Oasis Burner and both AC
Heating Elements. The Burner, AC #1 and AC #2
Buttons will highlight when active. This screen
also displays the Oasis System operational
Status and Faults.

Page 12
TEMP SCREEN
The Temp screen is accessed by pressing the
Temp Button located on the Home Screen. This
screen displays the Outside Air Temperature
and only exists on systems without the optional
Floor Heat.
FLOOR SCREEN OPTIONAL FLOOR HEAT
FLOOR HEAT with No Time Schedules
FLOOR HEAT with Time Schedules
The Floor Screen is accessed from the Floor
Button located on the Main Screen. This screen
controls the Floor Heat Zones by means of the
slider bars or the up and down arrows and is
only available on systems with the Floor Heat
option.. The higher the number, the longer the
time interval the heat mats are energized. This
screen also contains icons that show the
heating mat status. When the icon is red the
mat is in heat cycle and when the icon is grey
the heat function is on but the mat is between
heating cycles

Page 13
FEATURES SCREENS SCREEN 1
The Special Features Screens are used for
system setup and diagnostics.
The additional screens are accessed via the
Up/Down Arrows.
Special Features Screen 1 allows access to the
following features:
Clock Button
Accesses the Clock Setup Screen
System Diagnostics Button
Accesses the System Diagnostics Screens
Monitor Configuration Button
Accesses the Monitor Configuration Screens
Auto Genstart Button
Accesses the Auto Genstart Configuration
Screens
FEATURES SCREENS SCREEN 2
Screen 2 allows access to the following
features:
View AC Power History Button
Accesses the AC Power History Screen
Auto Fill Configuration Button
Accesses the Auto Fill Configuration Screens
Warnings Configuration Button
Accesses the Warnings Configuration Screens
Tank Calibration Button
Accesses the Tank Calibration Screens
FEATURES SCREENS SCREEN 3
Screen 3 allows access to the following
features:
Climate Configuration Button
Accesses the Climate Configuration Screens
TM102 Configuration Button
Accesses the TM102 Configuration Screen
Component Versions Button
Accesses the Component Versions Screen
View Splash Screen Button
Accesses the Splash Screen

Page 14
FEATURES SCREENS FLOOR HEAT OPTION SCREEN 1
This screen is the same as the Base System
Screens
FEATURES FLOOR HEAT OPTION SCREEN 2
This screen has the optional Floor Heat
Configuration Button
Floor Heat Option Screen 2 allows access to the
following features:
View AC Power History Button
Accesses the AC Power History Screen
Auto Fill Configuration Button
Accesses the Auto Fill Configuration Screens
Floor Heat Configuration Button
Accesses the Floor Heat Configuration Screen
Warnings Configuration Button
Accesses the Warnings Configuration Screens
FEATURES FLOOR HEAT OPTION SCREEN 3
Floor Heat Option Screen 3 allows access to the
following features:
Tank Calibration Button
Accesses the Tank Calibration Screens
Climate Configuration Button
Accesses the Climate Configuration Screens
TM102 Configuration Button
Accesses the TM102 Configuration Screen
Component Versions Button
Accesses the Component Versions Screen

Page 15
FEATURES FLOOR HEAT OPTION SCREEN 4
Floor Heat Option Screen 4 allows access to the
following features:
Climate Configuration Button
Accesses the Climate Configuration Screens
TM102 Configuration Button
Accesses the TM102 Configuration Screen
Component Versions Button
Accesses the Component Versions Screen
View Splash Screen Button
Accesses the Splash Screen

Page 16
FEATURES CLOCK SCREENS
.
The Clock Screen is accesses by pressing the
Clock Button from The Features Screen.
This screen displays the system time, outside
temperature, system warnings/errors and
allows you to access both the Alarm Clock and
Countdown Timer functions.
Pressing the Alarm Button will take you to the
Alarm Clock page. On this page are two scroll
bars that allow you to set the time of day for
the alarm. This page also contains a Back Button
that returns you to the previous page, as well
as, an up/down arrow that allows you to toggle
the alarm between the Off, Once Only or Every
Day settings and a Set Clock Button. The Set
Clock Button takes you to Monitor
Configuration page 1, which allows you to set
the system time.
Pressing the Timer Button on the Clock Screen
accesses the Countdown Timer screen. This
screen has two scroll bars that allow you to set
the countdown minutes and seconds. There is a
Start Button on this screen that when pressed
begins the countdown timer. This screen also
has Back and Set Clock Buttons the same as the
Alarm Clock screen.

Page 17
FEATURES SYSTEM DIAGNOSTICS SCREEN 1
The first Systems Diagnostics Screen is accessed
by pressing the System Diagnostic Button
located on the Features Screens or from the
“Prev”Button located on second Systems
Diagnostics Screen. This Screen displays any
system faults present on the control system.
FEATURES SYSTEM DIAGNOSTICS SCREEN 2
The second Systems Diagnostics Screen is
accessed by pressing the Next Button located
on the first Systems Diagnostics Screen or from
the “Prev”Button located on third Systems
Diagnostics Screen. This Screen displays
communications status present on the control
system.
FEATURES SYSTEM DIAGNOSTICS SCREEN 3
The third Systems Diagnostics Screen is
accessed by pressing the Next Button located
on the second Systems Diagnostics Screen. This
Screen displays additional communications
status present on the control system.
Pressing the Reset TM102 Button will reset the
TM102 Module..

Page 18
FEATURES MONITOR CONFIGURATION SCREEN 1
The first Monitor Configuration Screen is
accessed by pressing the Monitor Configuration
Button located on the Features Screens or from
the “Prev”Button located on second Monitor
Configuration Screen. This Screen allows you to
set the system time and date by pressing the
associated up and Down Buttons.
FEATURES MONITOR CONFIGURATION SCREEN 2
The second Monitor Configuration Screen is
accessed by pressing the Next Button located
on the first Monitor Configuration Screen or
from the “Prev”Button located on third
Monitor Configuration Screen. This Screen
allows you to set the Day Time Display Setting
by pressing the associated Up and Down
Buttons.
FEATURES MONITOR CONFIGURATION SCREEN 3
The third Monitor Configuration Screen is
accessed by pressing the Next Button located
on the second Monitor Configuration Screen or
from the “Prev”Button located on fourth
Monitor Configuration Screen. This Screen
allows you to set the Night Time Display
Settings by pressing the associated Up and
Down Buttons.