Cooper Security Homelink55 User manual


Security System
User Guide
Homelink55
A B C D
1 2 3
4 5 6
7890



Controls and Displays ..................................3
Key Functions: ................................................4
Display ...........................................................4
Access to the System ......................................5
Level Setting System ....................................6
Full Setting .....................................................6
Part Setting ....................................................8
Unset a Level setting system ..........................9
Partitioned System .....................................10
Setting Partitions ..........................................10
Unsetting Partitions: .....................................12
Setting With a Telecommand ........................13
Unsetting With a Telecommand ...................14
Alarms .......................................................15
Types of Alarm .............................................15
Silencing an Alarm ........................................16
© Cooper Security Ltd. 2004
Every effort has been made to ensure that the contents of this
book are correct. However, neither the authors nor Cooper Security
Limited accept any liability for loss or damage caused or alleged to
be caused directly or indirectly by this book. The contents of this
book are subject to change without notice.
Printed and published in the U.K
Part Number 11655629 issue 1






A B C D
123
456
7890








Press to confirm a command.
Press to cancel a command.
1 to 0 Used when keying in access codes.
A, B,
C, D
Used to select levels or partitions
If enabled by the Installer:
1 and 3 Start panic alarm
4 and 6 Start medical alarm
7 and 9 Start fire alarm

The display shows messages and prompts to help guide
you through setting, unsetting and programming the
system.
When the system is idle (either while set or unset) the
display shows the “standby screen”, comprising the time
and date:
6 Dec 2005 17:22
Homelink55
The bottom line of the display shows either the model
number of the control unit of your alarm system, or a
customised banner message from your installer.
Note: Your installer may have programmed the control
unit to blank the display after a few seconds. This is
normal, and is designed to provide added security by
concealing the state of the alarm system from potential
intruders.
To draw your attention to special events the keypad may
also illuminate one or more of the lamps to the left of the
display:
Alert. Flashes to highlight unacknowledged
alarm, fault or tamper conditions. Glows for
acknowledged conditions. Goes out when all
conditions are rectified.
Service. Glows if the system needs an installer
reset.
Mains. Glows when using mains power. Flashes
when using stand-by battery.
Note that your installer may program this lamp
to remain off for most of the time, and to glow
for 30 seconds after you have entered an access
code or presented a proximity tag (see “Access
to the System” on the next page).



To operate the system you must identify yourself by:
EITHER entering a four digit
access code on the keypad
1 2 3
4 5 6
7 8 9 0
OR presenting a proximity tag
to the top left corner of the case
A B C D
Your access code or your tag are are unique to you. You
can use either code or tag for any of the operations shown
in this guide.
Ask your Administrator to give you your code or tag. Do
not divulge or share them with anyone else.




Make sure the system is idle. Secure all your windows and doors.
Do this: The display shows:
1
1 2 3
4 5 6
7 8 9 0
OR
A B C D
System OK
Set?
2
0
Setting A 009


3
4
Set ABCD
Homelink55
Notes:
If you decide you want to stop setting then key in your access code again and press , or present your tag to
the keypad and press .



Make sure the system is idle. Secure all your windows and doors.
Do this: The display shows:
1
1 2 3
4 5 6
7 8 9 0
OR
A B C D
System OK
Set?
2
A B C D
Select A, B, C or D
corresponding to the level
you wish to set.
Setting B 009
3
Set B
Homelink55



Do this: The display shows:
1The control unit
starts the entry
tone.
A B C D
2
1 2 3
4 5 6
7 8 9 0
OR
A B C D
B Unset
The system gives a double “beep” to inform you that it
has unset. The display briefly shows the level the system
is unsetting.
6 Dec 2005 17:22
Homelink55




The installer may have created “partitions” in your system, and allocated you to one or more of them.
You may set and unset each partition independently of all the others. First, secure all windows and doors in the partition
that you wish to set.
Do this: The display shows:
1
1 2 3
4 5 6
7 8 9 0
OR
A B C D
System OK
Set? ABCD
Note that the display shows only those partitions you
have access to, and those that are currently unset.
2
A B C D
Select the partition you
DO NOT wish to set (for
example A, C and D).
System OK
Set? B


3
0
Setting B 009
4
Set B
Homelink55



Do this: The display shows:
1The control unit starts the
entry tone.
A B C D
Entry B
Homelink55
2
1 2 3
4 5 6
7 8 9 0
OR
A B C D
B Unset
Homelink55
Note: The control unit shows the
partitions you have access to, not necessarily the whole
system.
6 Dec 2005 17:22
Homelink55
The system unsets the selected partitions (B in this example) and displays the standby screen.



Note: The Installer must program the control unit to recognise (“learn”) a telecommand.
Make sure the system is idle.
Secure all your windows and doors.
Do this: The display shows:
1Press the
appropriate
button on the
telecommand.
Setting A 009
2
Set A
Homelink55



Do this: The display shows:
1
A B C D
6 Dec 2005 17:22
Homelink55
2 Press the appropriate
button on the
telecommand.
A Unset
6 Dec 2005 17:22
Homelink55




The control unit normally raises an alarm when it receives an alarm signal from one of its detectors. In addition, you can
start some types of alarm from the keypad. The table below shows the different kinds of alarms the control unit can
raise.
Signal (see note) Type of Alarm Started by:
Loud warbling tone from siren. Intruder Normal alarm or entry route zone activated when system is set.
24 hour zone activated at any time.
“ Tamper Someone has opened the case of one of the system
components, or cut the wires to a hardwired detector.
“ Panic PA zone or Panic Alarm transmitter activated at any time.
1 and 3 pressed on keypad.
Repeated “Dee Dah” from siren. Fire Fire zone activated at any time.
7 and 9 pressed on keypad.
Repeated, low volume “beeps”
from the keypad.
System Fault Mains failure, power failure on a radio peripheral, low battery
on detector, battery fault in control unit.
“ Technical Technical alarm zone activated at any time.
No audible tone.
(see note)
Medical 4 and 6 pressed on keypad.
Note: As well as any audible signal, the installer can program the control unit to send electronic messages over the
telephone network.



In an alarm the control unit gives a tone from the siren (except for medical alarms). The siren runs for a limited time set
by the installer (a maximum 20 minutes for intruder and PA alarms).
If you return to the system after the siren has stopped then the lamp on the display tells you that an alarm has
occurred. If you return to the system while the siren is running you can silence the siren as follows:
Do this: The display shows:
1
1 2 3
4 5 6
7 8 9 0
The siren stops and
the screen shows the
first zone to cause the
alarm, for example:
Burg Z02 Alarm
Homelink55
2EITHER The display returns to normal.
OR The installer may have programmed your system so
that the screen will tell you where the alarm occurred, and
also show a message asking you to call the installer.
Burg Z02 Alarm
Call Installer
0
The display returns to the
standby screen, but the
lamp glows .
6 Dec 2005 17:22
Homelink55
Call your installer and tell them that an alarm has occurred.