Cooper Security i-On 40 User manual

Security System
Installation Guide

Page ii
© Cooper Security Ltd. 2010
Every effort has been made to ensure that the contents of this book are correct. However,
neither the authors nor Cooper Security Limited accept any liability for loss or damage caused
or alleged to be caused directly or indirectly by this book. The contents of this book are subject
to change without notice.
Printed and published in the U.K.
This manual applies to the i-on40 control unit with version 2.02 software.
For Your Safety
This book contains several passages alerting you to potential problems or hazards. Each of
these are marked by the words Note, Caution or WARNING.:
Note: Describes conditions that may affect the proper functioning of the
equipment (but will not damage the equipment).
Caution: Describes actions that will physically damage the equipment and
prevent its proper function.
WARNING: Describes actions that are hazardous to health, or cause injury or
death.
Please pay particular attention to these marked passages.
Other Publications for the i-on40:
User Guide Instructions for setting and unsetting an alarm system
based on the i-on40.
The following guides are available from the Cooper Security website:
www.coopersecurity.co.uk
Administrator’s Guide Detailed notes for the system administrator of an alarm
system based on the i-on40.
Programming Reference Guide A detailed description of the Installer’s programming options
available on the i-on40.
Web Server Setup Guide Instructions on how to configure a Windows PC or laptop to
use the i-on40’s built-in web server for installation
programming.
i-on Updater Installation and
User Guide
This booklet shows you how to install i-on Updater on your
PC and use it to update the software on your i-on40 control
unit.

Page iii
CONTENTS
1. Introduction..................................... 1
Communications............................... 1
Level Setting or Partitioned System..... 1
2. Before You Begin.............................. 2
Preparation ......................................... 2
Siting the Unit.................................. 2
Guided Tour ........................................ 2
Opening the Control Unit Case............ 2
Control Unit PCB............................... 3
Keypad Controls and Displays............. 3
Opening the Keypad ......................... 3
Power Availability................................. 4
3. Installation ...................................... 5
Step 1. Fit the Control Unit Case ............ 5
Caution: Static Electricity................... 5
Fitting............................................. 5
Installing the Lid/Back Tamper ........... 5
Step 2. Fit and Connect the Keypad(s) .... 5
Siting the Keypad(s) ......................... 5
Fitting............................................. 6
Connecting Keypads to Control Unit .... 6
Keypad Addressing ........................... 7
Backlight Control .............................. 7
Tone Volume ................................... 7
Step 3. Connect Control Unit to Mains..... 8
Mains Cabling .................................. 8
Mains Connection ............................. 8
Step 4. Connect Wired Zones................. 8
Four Wire Closed Circuit Connections... 8
Fully Supervised Loop Connections...... 8
Step 5. Connect Wired Peripherals.......... 9
Remote Loudspeaker (Optional).......... 9
Wired External Sounders (Optional) .... 9
Wired Outputs (Optional)................... 9
Step 6. Fit a Plug-By Communicator ..... 10
Step 7. Fit and Connect Battery ........... 10
Programming Before Installation....... 11
Step 8. Initial Power-Up...................... 11
Step 9. Commission the System........... 12
4. Programming ................................. 13
Entering the Installer Menu ................. 13
Leaving the Installer Menu .................. 13
Important! Saving Changes................. 13
Restoring Access Codes ...................... 13
Restoring Factory Defaults .................. 14
Installer Menu ................................... 15
Zone Types & Attributes ..................... 16
Output Types .................................... 18
Exit Modes ........................................ 21
7. Maintenance................................... 21
8. Technical Specification ................... 22
General ............................................ 22
Capacities......................................... 22
Security............................................ 22
Radio ............................................... 22
Power Supply .................................... 22
EN50131-6 ratings: ........................ 23
Electromagnetic Compatibility .............. 23
Outputs ............................................ 23
Fuses ............................................... 23
Electrical Safety ................................. 23
Other ............................................... 23
Compliance Statements....................... 23
Compatible Equipment ........................ 24

i-on40
Page iv
This page is intentionally blank.

i-on40
Page 1
1. Introduction
The i-on40 is the control unit for a hybrid
wired/wirefree alarm system intended for
domestic and light commercial use.
The control unit comprises an ABS plastic
case which contains the radio transceiver,
power supply and backup battery. Up to
four separate wired keypad(s) can connect
to the control unit by standard alarm cable.
The keypads allow end users to set and
unset the system, and the installer to
configure the control unit. The keypads also
contain integral proximity tag readers,
allowing end users to control the system
without having to remember access codes.
A range of wireless peripherals is available
for operation with the control unit. These
include a door contact/universal
transmitter, a passive infra red detector,
smoke detector, external siren, 4 button
remote control, and remote radio keypad.
The control unit supports up to 16 wired
alarm zones, 24 wirefree alarm zones, up
to 16 hardwired outputs, 50 four-button
remote controls, 50 two-button radio panic
alarms, and 50 users. See page 22.
Communications
The i-on40 provides sockets for an add-on
communication module. The available
modules are:
i-sd02
(ATS2)
A speech dialler and public
switched telephone network
(PSTN) module that allows the
control unit to send recorded
speech messages and report
alarm information using standard
protocols such as Fast Format,
SIA and Contact ID. This module
also allows remote maintenance.
i-dig02
(ATS2)
A switched telephone network
(PSTN) module that allows the
control unit to report alarm
information using standard
protocols such as Fast Format,
SIA and Contact ID. This module
also allows remote maintenance.
i-gsm02
(ATS02)
A GSM module that allows alarm
reporting, speech messaging and
SMS text messaging over the
mobile phone network.
8750 An Ethernet module that allows
alarm reporting and remote
maintenance over the internet.
8844 A GPRS module that allows
internet protocol access over the
mobile phone network.
The control unit also provides outputs that
can be used to fit a “plug by”
communicator.
To comply with EN50131 you must fit an
ATS2 communicator.
Level Setting or Partitioned System
The i-on40 offers two basic ways of
behaving as an alarm system:
Part Setting. In a Part Setting system the
i-on40 can set in one of four ways: either
Full set or three varieties of Part Set. In Full
set the control unit pays attention to all
detectors. In each of the three Part Sets
the control unit ignores detectors that do
not have the appropriate Part Set attribute
(see page 17 ).
Partitioned System. In a Partitioned
system the i-on40 provides the equivalent
of four, smaller, independent alarm
systems. Each system is a “Partition” of the
i-on40. You can allocate any zone to each
Partition. Each zone can also belong to
more than one Partition. Each Partition can
have a Full Set level and one Part Set
Level. During installation the installer can
allocate keypads, sounders or outputs to
any of the partitions.
This manual shows the simple procedure
required to install the control unit and its
keypad. When you have completed the
physical installation please consult the
Programming section for details of
configuring the system to meet your exact
requirements.
For a detailed description of the Installer’s
programming menu please read i-on40
Programming Reference Guide available
from www.coopersecurity.co.uk.
Note: Some programming options can
make the installation non-compliant with
EN50131. The relevant options are noted in
Appendix 1 of the i-on40 Programming
Reference manual.

i-on40
Page 2
2. Before You Begin
Preparation
Before installation you should carry out a
survey of the site. You need to know how
many and what kind of detectors will be
transmitting to the control unit. You also
need to assess where the control unit must
be placed in order to receive radio signals
from the detectors successfully.
To do this you should conduct signal
strength tests. Cooper Security produce the
Scantronic 790r hand held signal strength
meter for this purpose. Alternatively, you
can power the control unit from a battery
and use its built-in testing facility to
measure the signal strength from a
detector that you temporarily place at each
planned location.
Siting the Unit
Do site the unit:
Upright (battery at the bottom).
Within a protected zone.
As high as possible. However, do make
sure that the unit is on a similar level to
the other transmitters or receivers.
Do NOT site the unit:
In the entry or exit zones, or outside
the area covered by the alarm system.
Close to or on large metal structures.
Closer than one metre to mains wiring,
metal water or gas pipes, or other metal
surfaces.
Lower than two metres from the floor
(ideally).
Inside metal enclosures.
Next to electronic equipment,
particularly computers, photocopiers or
other radio equipment, CAT 5 data lines
or industrial mains equipment.
Note: Some window glasses, especially
those sold as “insulating” or “energy
conserving” may be coated with thin metal
or conducting films. These glasses are
particularly poor at transmitting radio
waves.
If fitting two or more keypads make sure
that you do not place the keypads within
one metre to each other. (The proximity
tag readers in each keypad will interfere
with each other.) Remember not to place
keypads on opposite sides of the same wall.
Guided Tour
Opening the Control Unit Case
To gain access to the interior of the control
unit undo the two screws at the top of the
case. Pull the top of the lid down, and then
lift the lid out of the retaining lugs at the
bottom of the case.
1
2
3
Figure 1 Opening the Control Unit.
WARNING: When connected to the mains
with power applied mains voltages are
present on the shrouded heads of the
terminal screws of the mains connector (“8”
in figure 1).
1
3
5
4
6
7
8
3
10
3
9
2
2
Figure 2 Control Unit
1. Central fixing keyhole.
2. Aerials.
3. Fixing holes.
4. Connector pins for Lid Tamper.

i-on40
Page 3
5. Printed circuit board (PCB).
6. Cable entry holes for detector and keypad
wiring.
7. Transformer.
8. Mains connector block. Note yellow power
rating label fitted next to the connector block.
9. Cable entry hole for mains.
10. Back Tamper switch (if fitted).
Control Unit PCB
1
2
6
4
3
5
7
8910
13
11
12
15
14
Figure 3 Control Unit Printed Circuit Board
1. Aerials (CAUTION: do not bend).
2. Tamper connector.
3. USB socket (Mini B).
4. Ethernet link activity LEDs.
5. 20VAC input (from transformer).
6. Battery connector.
7. Kick Start pins.
8. Ethernet socket.
9. “Heartbeat” LED
10. RS485 terminator.
11. Code reset pins.
12. Plug by connector pins 13-16.
13. Plug by connector pins 1 to 12.
14. Comms activity LED.
15. Sockets for plug on module.
1 2 43
59 76810
Figure 4 Control Unit Main Connectors
1. Aux power.
2. Outputs (relay).
3. Aux power.
4. Keypad bus.
5. Wired zone connectors.
6. Ethernet connector.
7. Loudspeaker.
8. Wired siren tamper return.
9. Outputs (transistorised).
10. 14.4V Siren supply (not used in UK).
Keypad Controls and Displays
A
B
C
D
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
2
3
4
6
5
8
7
1
Figure 5 Controls and Displays
1. LCD display (2 x 20 characters).
2. Programming keys.
3. Navigation keys
4. Alert LEDs
5. Setting and unsetting keys.
6. Panic Alarm (PA) keys.
7. Number/text keys.
8. Set/Unset LEDs.
Opening the Keypad
Note: For EN50131-3:2009, 8.7 the keypad
is a type B ACE, fixed.
To open the keypad first gently prise off the
trim on the front and remove the two
screws. Next, carefully lever the front of the
keypad (containing the pcb and display)
away from the keypad rear housing.
1
2
3
4
Figure 6 Opening the Keypad

i-on40
Page 4
2
4
3
3
1
Figure 7 Keypad Rear Housing
1. Central keyhole.
2. Rear tamper shroud.
3. Cable entry.
4. Fixing holes.
1
4a
4b
3
4
6
2
5
4
3
2
ABCD-ON
ON
BRIGHT
BACKLIGHT
ET B A 12V 0V
Figure 8 Keypad PCB
1. Sounder.
2. Sounder volume control.
3. Tamper switch.
4. Jumpers for addressing and LED function:
4a Addressing
4b LED functions
5. RS485 termination jumper
6. Connector for control unit (note that the ET
terminals are inactive).
Power Availability
Before connecting any external devices to
the control unit, you must make sure that
the control unit can provide sufficient
current to power the system during a mains
failure for the time required to meet Grade
2 PD6662 or EN50131-1. The standard
requires 12 hour standby, which includes
two periods of 15 mins in alarm.
The amount of current available from the
control unit depends on the battery fitted.
The current taken by the control unit pcb,
communicator and keypads is given in
Technical Specifications on page 22.
For example: in an alarm system with an i-
on40 control unit, two i-kp01 keypads, and
15 wired PIRs the system takes the
following total quiescent current:
Device Current
Control unit PCB 130mA
15 x PIRs at 15mA each 225mA
i-sd02 communicator
(quiescent)
20mA
2 x i-kp01 at 30mA each
(backlights off)
60mA
Siren (quiescent) 25mA
Total 460mA
During an alarm, these figures become:
Device Current
Control unit PCB 220mA
15 x PIRs at 15mA each 225mA
i-sd02 communicator 50mA
2 x i-kp01 at 30mA each
(backlights off)
60mA
Ext Siren & Strobe 400mA
Total 955mA
The total amp hours required =
(0.460A x 11.5h) + (0.955A x 0.5h) =
5.77Ah
A fully charged 7Ah battery can provide this
amount of charge.
In this example a 7Ah battery should
exceed the Grade 2 requirements.
Note: All current drawn from the Aux
terminals (12V and 14.4V) must be
included in the overall calculation..

i-on40
Page 5
3. Installation
Exposure to Radio Frequency Radiation
The radiated output power of this device is
below those levels considered safe by
European exposure limits. Nevertheless,
when fitting the product place it in such a
manner as to minimise the potential for
human contact during normal operation. To
minimise exposure, users should be more
than 200 mm from the device during
normal operation
Step 1. Fit the Control
Unit Case
Caution: Static Electricity
Like many other electronic products, the
control unit contains components that are
sensitive to static electricity. Try not handle
the PCB directly. If you must handle the
PCB, take the standard precautions against
damage by static electricity.
Fitting
1
1
2
1
1
2
Figure 9 Fixing Holes and Cable Entries
1. Fixing holes.
2. Cable entries.
To prevent access to the inside of the
control unit, you must mount the back of
the control unit on a wall, using at least
four fixing holes. Use No10/M5 countersunk
screws at least 36mm long. Figure 9 shows
the fixing holes and cable entries.
Protect the unit from dust and drilling
debris when drilling the fixing holes.
Installing the Lid/Back Tamper
Fit and connect the combined lid/back
tamper (provided). Ensure that the switch
is oriented as shown in Figure 10.
Figure 10 Lid/Back Tamper
Item 2 in Figure 3 shows the connector for
the lid/back tamper.
Step 2. Fit and Connect
the Keypad(s)
Siting the Keypad(s)
Do site the keypad(s):
Within the area protected by the alarm
system.
At a convenient height and location for
the user.
Out of sight of potential intruders.
Do NOT site the keypad(s):
Next to electronic equipment,
particularly computers, photocopiers or
other radio equipment, CAT 5 data lines
or industrial mains equipment.
Where the cable run from the control
unit will be longer than 100m (see
Cable Configuration and Length).
Note: Do not site two or more keypads
closer than one metre together, otherwise
their prox readers will interfere and be
unable to read tags.

i-on40
Page 6
Fitting
Use M4 25mm countersunk screws in at
least three fixing holes when mounting the
back of the keypad on the wall.
Figure 11 Screw Keypad Back Box to Wall
Connecting Keypads to Control Unit
Cable Type
In general, the control unit requires
standard 7/0.2 un-screened four core alarm
cable for wiring to keypads.
For maximum performance in harsh
environments use twisted pair cable with a
characteristic impedance of 100-120ohms
eg: CAT5 or cable designed for RS485.
Use one pair for data bus A & B. Use the
other pair for 12V & 0V. For optimum
performance the voltage at the keypad
should be greater than 12V.
Screened cable may prove necessary if the
installation site has equipment that
produces high levels of R.F. (Radio
Frequencies), for example welding
equipment. If screened cable is required,
you should keep to the following guidelines:
1. Avoid earth loops by connecting the
screen on the cable to mains earth at
the control unit but not at the keypad.
2. The continuity of the cable screen is
most important and screens MUST be
continuous along the full length of the
cable.
3. If the cable enters any metal enclosure,
ensure the screen is isolated from the
case.
Cable Segregation
Segregate the keypad cabling from any
other wiring, such as mains supply cables,
telephone cables, computer network cables
and R.F. cables. Use cable ties to keep
cables separated.
Keep the keypad cable clear of cables
supplying sounders or extension
loudspeakers.
Cable Configuration and Length
You can connect up to four wired keypads
to the control unit. You may connect the
keypads either in daisy chain (serially), or
in star (parallel) configuration at the control
unit connector.
250m
terminate
terminate
Sta
r
Daisy Chain
100m MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9wxyz
MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9wxyz
MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9wxyz
MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9wxyz
MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9 wxyz
MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9 wxyz
MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9wxyz
MENU
A
B
1
4ghi
7pqrs
*0#
2abc
5jkl
3def
6mno
8tuv 9 wxyz
Figure 12 Keypad Wiring Configurations
For star configurations the cable length
from control unit to the most distant
keypad should not exceed 100m. For a
daisy chain configuration the total cable
length should not exceed 250m,
Connection
Figure 13 shows the wiring connections at
the keypad and control unit.
ET B A 12V 0V
Figure 13 Keypad Connection

i-on40
Page 7
Temination
The i-on40 data bus uses the RS485
interface. Because of this the ends of the
line in some configurations may be
terminated to improve performance in
electrically noisy environments or where
there are long cable runs. Both control
panel and keypads have a termination link
on their PCBs (see 10 in Fig 3 for the
control unit and 5 in Fig 8 for the keypad).
Fitting a jumper to the pins adds a
termination to the cable.
In a daisy chain configuration terminate
each end of the chain (see Fig 12 ).
In a star configuration:
If there are only two keypads then this
is the same as a daisy chain
configuration. If required terminate at
each keypad.
If there are more than two keypads
AND two cables are long while the
remaining keypad cables are short (less
than 10m) then it is possible to
terminate at the two keypads with long
cables.
If there are more than two keypads BUT
each keypad cable is more than 10m
then DO NOT terminate.
Keypad Addressing
Each keypad connected to an control unit
must have a unique address. See Figure 8
on page 4 for the position of the addressing
jumpers.
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
*0#
MENU
A
B
1
4 ghi
7 pqrs
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
4
3
2
4
3
2
12
43
4
3
2
4
3
2
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
Figure 14 Keypad Addressing Jumpers
Backlight Control
You can control the appearance of the
keypad backlights and set/unset LEDs by
fitting links over the appropriate jumpers
on the keypad pcb (see Figure 8 on page 4
for the position of the jumpers).
The jumpers have the following functions:
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ABCD-ON
The set/unset LEDs are disabled.
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ABCD-ON
The set/unset LEDs shows the setting
status of the system. (Full set is left
hand led.)
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ON
BRIGHT
BL
The key backlights are disabled. They
will glow briefly for five seconds when a
user presses a key.
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ON
BRIGHT
BL
The key backlights glow all the time at
normal intensity.
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
MENU
A
B
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ON
BRIGHT
BL
The keypad backlights glow all the time,
extra bright.
Tone Volume
To alter the volume of non-alarm tones
from the keypad adjust the keypad sounder
volume control (2 in Fig 8):
Louder
Note: This control changes
the volume of non-alarm
tones (for example
Exit/Entry tone). The volume
of alarm tones is fixed.
Softer

i-on40
Page 8
Step 3. Connect Control
Unit to Mains
WARNING: ENSURE THAT THE MAIN
SUPPLY IS DISCONNECTED AND ISOLATED
BEFORE MAKING ANY MAINS
CONNECTIONS. All mains electrical
connections must be carried out by a
qualified electrician and must comply with
the current local regulations (e.g. IEE).
Mains Cabling
Make sure that the mains supply cable does
not run vertically behind the aerials within
the control unit case.
If you wish run mains cable through the
side of the case, make sure that they are
horizontal for the last metre before entering
the case.
>1m >1m
Figure 15 Mains Cabling Clearance
Note: To avoid mains interference, the
mains cable must enter the control unit
through its own cable entry hole ( 9 in Fig
2) and must not be mixed with other
cables.
Mains Connection
Figure 16 shows the mains connection.
Connect to a suitable supply using a
double pole disconnect device in
accordance with EN60950-1.
Caution: Do not apply power at this point.
Anchor the mains cable with a strain-relief
tie. There is a eye located near the mains
cable entry hole for this purpose.
L
N
T250mA 250
V
230V ~50Hz 200mA
Figure 16 Mains Connection
Step 4. Connect Wired
Zones
Four Wire Closed Circuit Connections
Tamper Zone 2
Alarm Zone 2
Tamper Zone 1
Alarm Zone 1
Figure 17 Closed Circuit Loop Zone Wiring
Fully Supervised Loop Connections
Figure 18 shows the wiring connections for
Fully Supervised Loop zones. Note that the
resistance values shown are examples.
The allowed values for Alarm Contact/End
of Line are: 4k7/2k2. 1k0/1k0, 2k2/2k2, or
4k7/4k7.
Use the same pair of values for ALL FSL
wired zone circuits.
When programming select the
correspondings value in Installer Menu - System
Options - Wired Zone Type
If you wish to connect two or more
detectors to a FSL zone, the diagram at the
bottom of Figure 18 shows the connections
required.
Figure 19 shows an example of wiring
double doors with two door contacts to one

i-on40
Page 9
FSL zone. Each door contact is a reed
switch, connected between the outer
terminals. The inner (shaded) terminal is
not connected, and provides a spare
terminal.
Zone 1
Zone 2
2K2 EOL
4K7
Alarm contacts
Tamper contacts
2K2 EOL
4K7
Alarm contacts
Tamper contacts
Zone 1 2K2 EOL
4K7
Alarm contacts Alarm contacts
Tamper contacts Tamper contacts
Max 10 devices per c
i
rcuit (not recommende
d
)
100 Ohms
Figure 18 Fully Supervised Loop Zone
Wiring
2K2 EOL
Spare
4K7 Black
Red
Blue
To zone •
contacts Yellow
Figure 19 Example: Wiring Two Door
Contacts to One FSL Zone.
Step 5. Connect Wired
Peripherals
12V +
0V
Tamper In
Tamper Out
Strobe +ve
Strobe -ve
Trigger -ve
+LS
-LS
Figure 20 Connecting Wired Peripherals
The control unit pcb provides four
connectors for wired outputs. Outputs 1
and 2 are voltage free relay outputs.
Outputs 3 and 4 are driven by transistors,
and are capable of sinking a maximum
500mA when active. By default outputs 3
and 4 are 0V when active, +12V when
inactive. If you wish to reverse the polarity
of these two outputs use Installer Menu -
Outputs - Wired Outputs – Output 3(4) - Polarity.
Remote Loudspeaker (Optional)
If you wish to add a wired Loudspeaker
unit, then connect it as shown in Figure 20.
Wired External Sounders (Optional)
Wired external sounders differ in their
methods of connection. Figure 20 shows an
example of a general method of using the
outputs to connect a wired sounder.
Note: If you do not wish to connect a wired
external sounder then make sure you link
TR to 0V. This prevents the control unit
reporting Bell Tamper unnecessarily.
Wired Outputs (Optional)
Figure 20 shows an example of using the
wired outputs to drive an indicator LED.

i-on40
Page 10
Step 6. Fit a Plug-By
Communicator
The control unit can be connected to a
separate communicator or speech dialler
(for example, the Scantronic 8400, 8440,
660 or RedCare STU). Figure 21 shows the
connections provided by the
communications wiring harness.
O/P9 (Brown)
O/P10 (Orange)
O/P11 (Yellow)
O/P12 (Green)
Com Connector Cable,
Part number 11960058
Com Connector Cable,
Part number 485210
Figure 21 Plug-By Communicator Wiring
Note: Comms O/P4 will be active when the
system is unset. This is normal.
To fit a communicator, follow the
instructions below.
Caution: Follow the instructions in the order
shown, or you may damage the
control unit and/or communicator.
1. Disconnect mains power, remove the
case lid, and disconnect the battery
from the control unit if the system has
already been installed.
2. Make any necessary connections from
the communicator to the communication
wiring harness. The default is a 12V
positive voltage when the output is
inactive.
Refer to the next section if you are
using a dual-path communicator.
3. Plug the Communication Wiring Harness
onto the communications connector on
the main PCB.
If the system has already been installed:
4. Re-connect the battery.
5. Fit the case lid.
6. Apply mains power.
7. Test communicator operation.
Line Monitoring for a Dual-Path
Communicator
If a standalone dual-path (landline and
mobile) communication device, such as a
RedCARE STU, is connected to the plug-by
connector, you need to do the following to
obtain correct line fault reporting (this is
not necessary if you are using a plug-on
module):
1. Wire a panel output programmed as
type "ATS Test" to the ATS Test input of
the communicator.
2. Wire the Line Fault output of the
communicator to the Line Fault input of
the plug-by connector. The
communicator must provide +12Vdc to
indicate a line fault (for example, if the
Line Fault output at the communicator
uses a relay, connect the common
terminal of the relay to +12Vdc and the
normally-open terminal to the Line Fault
input of the plug-by connector).
The panel will generate an "ATE L.F. Single"
alert if only one of the networks is not
available, or "ATE L.F. All" if both networks
are not available.
Step 7. Fit and Connect
Battery
Fit a 7Ah Lead Acid battery into the battery
compartment in the bottom of the control
unit, see Figure 22.
Make sure that you secure the battery to
the case with the strap provided. Connect
the battery leads, red to the positive, black
to the negative terminals of the battery.
Figure 22 Fitting the Battery

i-on40
Page 11
Note: Connecting the battery without mains
power will not start the system. (See
“Programming A Control Unit Before
Installation” below if you wish to start the
system on battery power.)
Programming Before Installation
If you prefer, you can make the control unit
learn the detectors and other peripherals
before installing the system in its final
location. You will need to temporarily
connect a keypad to the control unit.
It is possible to operate the control unit
from battery power (or a 12Vdc supply)
without connecting the unit to a mains
supply. However, in order to start the
control unit processor running you must
briefly short the Kick Start pins together
after connecting the battery.
When programming the system while it is
running on battery only, remember to leave
the Installer Menu before removing power.
If you do not do so all your changes will be
lost, see Important! Saving Changes on
page 13
If you wish to program the control unit
from a laptop or PC you can do this by
connecting the control unit to your PC via
Ethernet. You will need a CAT 5 patch cable
and a laptop or PC with a standard web
browser. See the separate publication i-
on40 Web Server Set Up Guide for
instructions on how to set up your
PC/laptop and the control unit.
Step 8. Initial Power-Up
WARNING: During initial power-up all the
keypad sounders and any internal
loudspeaker MAY give an alarm tone. If you
are working at the top of a ladder make
sure that the sudden noise does not startle
you and cause a fall.
1. Apply battery then mains power to the
control unit.
The keypads and internal sounder may
give an alarm tone. The heartbeat LED
(see fig 3 ) starts flashing.
The display initially shows:
Language?
English
2. Press uor nto show other languages
on the bottom line of the display. for
example:
Language?
Nederlands
3. Press Yto select the language you want.
From this point on, the display operates
in the selected language. If you want to
change the language later use Installer
Menu - System Options - Language.
The display shows:
COUNTRY DEFAULTS
*UK
4. Press uor nto show other countries,
for example:
COUNTRY DEFAULTS
Italy
5. Press Yto select the country you want.
The display shows:
A : Partition mode
B : Part set mode
6. Press A or B to select either a
partitioned system or a Part Setting
system.
The display shows:
Load Profile?
7. Either: Press Yto load the Profile.
Or: Press Xto start with a blank
system
Note: Profiles may not be EN50131
compliant. Please check the i-on40 web
page on www.coopersecurity.co.uk for a list
of the available profiles. (The factory
default is EN50131 compliant.)
The control unit loads your choice of
profile, and then shows:
WIRED ZONE TYPE
*2-wire FSL 2k2/4k7
8. Press uor nto show the range of
wiring types available, for example:
WIRED ZONE TYPE
4-wire CC
9. Press Yto select the wiring type you
intend to use for the wired zones
The display shows:
INSTALLER EXIT FLTS
Panel lid open
Note that the alert LEDs round the
navigation glow red. This is because the
control unit lid is off and the tamper is
active.
10. Press X.
The display shows:
INSTALLER MENU
Detectors/Devices
At this point you can carry on to
commission the system. See the next page.
Note: Setting the time and date is an
administrative user function. See i-on40
Administrator’s Guide for instructions.

i-on40
Page 12
Step 9. Commission the
System
After installing the control unit you should
commission the alarm system as follows:
1. Use the Installer Menu (see Chapter 4)
to teach the control unit the identity of
its radio detectors and any other
peripherals. See the installation
instructions supplied with each detector
or peripheral.
2. Install detectors and peripherals at their
selected locations.
3. Use the Installer Menu – Test (see
Chapter 5) option to:
a) carry out a walk test of the detectors.
b) test the operation of any other
peripherals.
4. Program the system to suit user
requirements. See the i-on40
Programming Reference for a detailed
description of the Installer Menu.
5. Assemble and close the control unit:
a) Hook the lid of the control unit into
the bottom of the case.
b) Close the lid and then tighten the two
fixing screws.
1
2
3
Figure 23 Replacing the control unit lid.
6. Leave the Installer Menu.
The red LEDs should go out, and the rim
of the navigation keys glow green. The
system is now ready to hand over to the
user.
7. Instruct the user on how to operate the
system. See the i-on40 User Guide and
the i-on40 Administrator’s Guide. If
necessary, show them how to set the
time and date on the system.
Note that you can obtain the
Administrator’s Guide from
www.coopersecurity.co.uk.

i-on40
Page 13
4. Programming
This section is summary of the Installer
Menu on the i-on40. Please see the i-on40
Programming Reference for a more detailed
description.
Entering the Installer
Menu
1. Make sure the system is unset and
showing the standby screen (time and
date).
2. Key in the Installer access code. When
delivered from the factory the default
Installer access code is “7890”. The
default user code is “1234”.
As you start to key in the code the
display shows:
Enter Access Code:
(* )
When you key in the last digit of the
Installer access code the display shows:
User Code Required
( )
Note: You will see this screen the first time
you enter the Installer menu on a new
control unit, or if you have restored Factory
Defaults.
3. Key in the default user code (see Note
below).
The display shows:
Installer Menu
Detectors/Devices>
4. Press uor nto display more items
from the menu.
Each item appears on the bottom line of
the display in turn, for example:
Installer Menu
Outputs >
5. Press >to select that item of the menu.
The option you selected now appears on
the top line. If there are any sub-
options for that selection, then the first
of them appears on the bottom line, for
example:
Outputs
Edit Outputs >
You can press uor nto display the
other sub-options.
Note: If you key in an access code
incorrectly, the display shows four “stars”.
Key in the code again. If you key in a total
of ten incorrect codes then the system locks
you out for 90 seconds.
Leaving the Installer
Menu
If you wish to leave the Installer Menu at
any time.
1. Press
Xuntil the display shows the
words “Leave installer mode?”.
Leave
installer mode?
2. Press Yto leave Installer menu.
(Press Xif you do not want to leave the
menu.)
The display shows the time and date.
i-on40
12:00 02/01/2008
The system is ready for use.
Note: If you attempt to leave the Installer
Menu when a detector tamper is active then
the keypad displays a fault message telling
you which detector is causing the problem.
Press
X to return to the Installer Menu.
You must either close the detector tamper
or delete it from the system before you can
leave the Installer Menu.
Important!
Saving Changes
When you make changes to the Installer
Menu the control unit holds those changes
in temporary memory until you leave the
Installer Menu. As you leave the Installer
Menu the control unit writes those changes
into a permanent store. If you remove all
power BEFORE you leave the Installer Menu
then the control unit will lose your changes.
Note that this does not apply if you restore
Factory Defaults, that change takes place
immediately.
Restoring Access Codes
If the user and/or Installer codes are lost
then ;
1. If possible, enter the Installer menu.
Note: If you cannot enter Installer Menu
then the control unit will start a tamper
alarm when you open the control unit lid.
2. Remove mains power, then open the
case and disconnect the battery.
Note: This procedure will not work if the
control unit lid tamper remains closed.
3. Identify the Reset Codes pins on the
main PCB (see Figure 3).

i-on40
Page 14
4. Short the Reset Codes pins together
using a screwdriver or jumper link.
(Keep the short on until step 6.)
5. Apply mains power.
The control unit loads the factory default
access codes:
User 1: 1234, Installer: 7890.
(All other users have been deleted.)
After a short pause the keypad display
shows the time and date. The red LEDs
glow to show an alert that the panel lid
is open. The sounders operate.
6. Remove the short from the Reset Codes
pins.
7. Reconnect the battery.
8. Close the control unit lid (to restore the
tamper switch).
9. Key in the Master User code, 1234, to
silence the sirens.
The LEDs around the navigation glow
red to show an alert for a tamper and a
missing battery.
Press Ytwice to (if necessary)
acknowledge any alerts.
To force the control unit to check the
battery:
10.Enter Installer Menu and then leave it
again.
The navigation key LEDs should now
glow green.
Note: The log is protected and cannot be
erased by the Installer.
Restoring Factory
Defaults
If you wish to restore all factory default
options then:
1. From the Installer Menu select System
Options – Restore Defaults – Factory Defaults.
The display asks for confirmation.
2. Press Yto load defaults.
(Press Xto go back to the Installer
Menu without changing defaults.)
The display asks you to select Partition
Mode or Part Set Mode.
3. Press A or B to select the desired mode.
The display asks you to select the zone
wiring type.
4. Press uor nto display the desired
wiring type on the bottom line of the
display and then press Yto select it.
The system loads all defaults except for
Access Codes and the Log.
The display shows:
Factory defaults
restored
5. Leave the Installer Menu to save the
change (press Xuntil the display shows
“Leave Installer mode ?” then
press Y).

i-on40
Page 15
Installer Menu
1 DETECTORS/
DEVICES
Detectors
Add/Del Detectors
Zone 17...40
Delete all
Edit Zones
Zone 01...40
Name
Type
Partitions1
Attributes6
Wired Keypads
Keypad 01...04
Name
Partitions1
Key A...B1
Radio Keypads
Add/Del Radio Keypad
Edit Keypads
Name
Partitions1
Key A...B1
External Sirens
Add/Delete Ext. Siren
Edit external siren
Info Modules
Teach Info Module
Updates
Ready-to-set LED
WAMs
Add/Del WAM
View WAM
2 OUTPUTS
Radio outputs
Add Outputs
Edit Outputs
Output 01...08
Name
Type
Wired outputs
Output 1...4
Name
Type
Polarity
Partitions*
Plug-by outputs
Output 1...12
Name
Type
Polarity
Partitions*
3 SETTING OPTIONS2
Full Set
Name
Exit mode
Settle time9
Exit time10
Entry time
Strobe on Set
Strobe on Unset
Part Set B
Name
Exit Mode
Settle time9
Exit time10
Entry time
Alarm Response
Part Set Final Exit
Part Set Entry Route
Strobe on Set
Strobe on Unset
Part C, D
(See Part Set B)
3 PARTITIONS1
Partition 1...4
Name
Exit Mode
Settle Time9
Exit Time10
Entry Time
Alarm Response
Strobe on Set
Strobe on Unset
Part Set Exit Mode
Part Set Settle Time9
Part Set Exit Time10
Part Set Entry Time
Part Set Alarm
Response
Part Set Final Exit
Part Set Entry Route
Part Set Strobe Set
Part Set Strobe Unset
Partition 2....4
Full Set Link
4 SYSTEM OPTIONS
Wired Zone type
User Access
PA keys active
Quick Set
Quick Omit
User code reqd
User reset
Zone alarms7
Zone tampers
System tampers
DD243
Confirmation
Confirmation time
After Entry
Entry Keypad Lock
Sounder on
Siren on
Unconfirmed reset
Confirmed reset
Profiles
Language
Restore Defaults
Installer Name
Installer Code
Keypad text
Remote Needs Entry
PA Response
Auto Rearm7
Siren Delay
Siren Time
Loudspeaker Volume
Entry Alarm Delay
Supervision
Jamming
Force Set
Tamper Omit
CSID Code
Silence Alerts
Mains Fail Delay
5 COMMUNICATIONS
ARC Reporting5
Call Mode
Phone book
IP Network5
Account Number
Report Type
Fast Format channels3
CID/SIA Events4
Restorals4
Burg Comms Rearm3
21CN FF Ack time3
Send tamper as burg4
Dynamic Test Call
Static Test Call
Speech Dialler5
Call Mode
Messages
Phone Book
Triggers
Destinations
Call Acknowledge
SMS5
Call Mode
Messages
Phone Book
Triggers
Line Fail Response5
Line Fail Delay5
IP Network (Own)
Web Server
GPRS5
Ethernet5
Downloading
Account
Connection Type
Rings to Answer5
Answer on one ring5
Access Mode5
Phone Book5
Secure Callback5
Modem Baud Rate5
6 TEST
Sirens & Sounders
Wired Keypad
Walk Test
Zone Resistances
Signal Strengths
Detectors
Radio Keypads
External Sirens
WAMs
Outputs
Radio Outputs
Wired Outputs
Plug-by outputs
Remotes
Panic Alarms
Prox Tags
ARC Reporting
Speech Dialler5
PSU Current
7 VIEW LOG
8 ABOUT
Panel
Comms
Panel Ethernet
1Appears only in a Partitioned system (or when zones have a type other than “Not Used”.
2Appears only in a Level Setting system.
3Appears only when Report Type=Fast Format
4Appears when Report Type=CID or SIA
5Options visible depend on communications module fitted.
6Appears when zone is given a type other than “Not Used”.
7Appears only when System Options – DD243 – Confirmation is “off”.

i-on40
Page 16
8Appears only when device learned in.
9Appears only if Exit Mode is “Final Door”.
10Appears only if Exit Mode is “Timed Exit” or “Silent Set”.
Zone Types & Attributes
(Hint: You can select a zone type quickly by
keying the number shown in brackets after
the type’s name, for example:“05” to select
Alarm Abort, “02” to select Panic Alarm,
“11” to select External PSU A/C Fail. The
number does not appear on the keypad
display.)
Not Used (00)
The alarm system will not respond
when an event triggers this detector.
Panic Alarm (01).
Operating a device programmed as
‘Panic Alarm’ (PA) will start an audible
alarm. If a communications module is
fitted there may also be an alarm
transmission to the Alarm Receiving
Centre (ARC), depending on how you
have programmed the ARC Reporting
option. PA alarms operate whether
the system is set or unset.
Fire Alarm (02).
Smoke or heat detectors connected to
Fire Alarm zones cause the sirens to
give a pulsing fire signal. Fire alarms
operate whether the system is set or
unset, and will always trigger
communications, if a communications
module is fitted and enabled.
Normal Alarm (03).
A zone programmed as ‘Normal
Alarm’ will start an alarm when the
system is set. (See “Zone Attributes”
on page 17.)
24 Hour Alarm (04).
Activating this zone causes an alarm
whether the system is set or unset.
Final Exit (05).
Zones of this type must be the last
detector to be activated on exit, or
the first to be activated on entry. You
can use zones of this type to finally
set the system, or to start the entry
procedure.
Note: If you give a Final Exit zone any of
the Part Set attributes then you can
program that zone to behave like a Normal
Alarm zone if the user part sets the system.
Entry Route (06).
Use this zone type for detectors sited
between the Final Exit door/detector
and the keypad. If an ‘Entry Route’
zone is triggered when the system is
set, an alarm will occur. If the
entry/exit timer is running when an
Entry Route zone is triggered then no
alarm occurs until the entry/exit timer
expires.
Note: If you give an Entry Route zone one
of the Part Set attributes then you can
program that zone to behave like a Final
Exit zone if the user part sets the system.
Technical Alarm (07).
Use this zone type when you want to
monitor equipment, for example a
freezer, without raising a full alarm. If
a technical alarm zone is activated
(and the control unit correctly
programmed) then the control unit
starts communication and logs the
event.
If the technical alarm occurs while the
system is set, then system makes no
audible alarm. When a user unsets
the system the keypad shows an
alert.
If a technical alarm zone is activated
while the system is unset then the
system starts an alert immediately
and gives a brief tone from the
keypad every few seconds. When a
user enters a valid access code the
keypad stops the tone and displays
the zone causing the alarm.
When the user acknowledges the alert
by pressing Ythe control unit resets
the technical alarm ready for the next
event.
Key Switch Momentary (08).
Note: The use of a keyswitch is not
compatible with EN50131-1. This is
because the system restore activation (on
the keypad) does not require a level 2 user
code.
Use this zone type to connect a momentary
keyswitch to a single zone.
In a Part Setting system the
keyswitch can Full Set or unset.
In a Partitioned system you can
allocate the keyswitch to one or more
partitions.
Each time a user operates the
keyswitch the control unit changes
the current set state.