Coopers of Stortford 10710 User manual

Wireless Telephone Signaller
10710 Instrucons for Use
Please read and retain these instrucons for future reference v001: 23/11/16
BATTERY INSTALLATION
+
Test
Telephone
Plug RJ11
Battery
compartment Open the cover
CODE PAIRING & MELODY SELECTION
Zone ID
Zone selector button
Melody selector
button
OPERATION
Plug the telephone line into the telephone RJ11 jack refer to the diagram. The system is now ready to use.
PA R T S & F U N C T I O N
Insert a CR2032
Baery (included)
The WIRELESS TELEPHONE SIGNALER works with the receiver
and must be paired prior to use.
Step 1: Insert the baery into the telephone transmier.
Step 2: Insert the baeries into the receiver (chime unit).
Step 3: Enter pairing mode for the receiver (chime unit). Press &
hold the ● zone selector buon for 3 seconds. The LED in
zone #1 will flash.
Step 4: Press the ● zone selector buon again to move to the zone
you wish to pair with. Press the ♫ melody selector buon
to scroll through the melodies. Once you hear a melody
you prefer, do not press any buon as the melody is set for
that zone.
Step 5: Once the zone and melody are selected, press the test buon on the telephone signaler once. If
successful, the receiver will generate a short tone. Press the ● zone selector buon to exit pairing
mode unit is now ready to use.
Alert Reset Buon
To cancel any alert on the remote receiver press the reset button. The reset button is located on
the back of the receiver behind the flasher.
Uses CR2032 Battery
Chime only
Chime/Strobe
Strobe only
The wireless Telephone Signaller is to be used in conjuncon with Wireless Receiver with Doorbell - Item
code 10708.
Head Office, 11 Bridge Street
Bishop's Storord CM23 2J U
Tel: [phone]*
Fax: [phone]
www.coopersofstorord.co.uk OF STORTFORD
*Calls Cost 7 pence per minute plus your telephone company's network access charge

CODE CONFLICT
If the telephone signaller coding is the same as another sensor you must change the code. After you have
changed the code, re-match the telephone signaller.
+
+
CR2032
Open the cover Remove the battery
BATTERY LOW INDICATOR
The status of one sensor baery is indicated on the receiver. Please refer to the “baery low indicator” on
the receiver.
Press & hold the test button, insert
the battery whilst holding the button
for 5 seconds. The LED will flash 5
times, when a new code is generated.
Keep baeries away from children and pets.
Remove the baeries if le for long periods.
Never dispose of baeries in a fire.
Follow the baery manufacturer’s safety, usage, and disposal instrucons.
BATTERIES
•
•
•
•
•
•
Do not mix used and new baeries.
•
•
•
•
DISPOSAL
•
•
Keep telephone signaller dry. If wet, dry immediately.
Do not use cleaning solvents on electronic products.
Solvents contain chemicals that can damage circuitry. Use damp towel or cloth to clean. Dry
immediately.
Do not expose the bell unit to rain or immerse in water. It is not water resistant.
WARNINGS / CAUTIONS
Wireless Telephone Signaller
10710 Instrucons for Use
Please read and retain these instrucons for future reference v001: 23/11/16
Baery disposal, spent or expired baeries must be properly disposed of and recycled in compliance
with local regulations. For detailed information, contact your local authority.
Dispose of all packaging, paper, cartons and plasc, plasc bags in accordance with your local
recycling regulaons.
At the end of the product’s lifespan please dispose of it at an authorised household WEEE waste
recycling centre.
Head Office, 11 Bridge Street
Bishop's Storord CM23 2J U
Tel: [phone]*
Fax: [phone]
www.coopersofstorord.co.uk OF STORTFORD
*Calls Cost 7 pence per minute plus your telephone company's network access charge