coov N100 Pro Parts list manual

COOV N100 Pro 功能秘籍
Function Instruction ofCOOV N100 Pro
以 X1，PS4，Pro，joy-con 手柄按键分布图为例：
Take the button distribution of X1,PS4,Pro,joy-con handle an example:

中左
Middle left button
十字键上
Up of cross button
十字键下
Down of cross button
上键
Up button
左键
Left button
右键
Right button
下键

Down button
中右
Middle right button
N100 Pro 蓝牙无线连接示意图：
N100 Pro Bluetooth wireless connection diagram:

连接设备（如连接示意图所示）
Connect the device (as shown in the connection diagram)

PS4 手柄连接蓝牙配对：
PS4 joypad connection Bluetooth pairing:
1、PS4 手柄处于断开关机状态。
1, PS4 joypad is in the off state.
2、长按手柄“SHARE+PS”键，直到手柄指示灯出现双闪（配对模式）。
2: Long press joypad "SHARE + PS" button until the joypad indicator double flash
(pairing mode).
3、将 N100 Pro 与蓝牙适配器按照示意图连接至游戏主机。
3: Connect the N100 Pro and Bluetooth adapter to the game console according
to the diagram.
4、等待 3-5 秒左右，手柄指示灯显示为紫色，游戏显示器上显示手柄连接成功并出现”
USB“提示，则连接成功。
4: Wait about 3-5 second s, you will see joypad indicator is displayed in purple and
the screen show joypad connection is successful and the "USB" logo, it means the
connection is successful.

Joy-con 左手柄连接蓝牙配对：
Joy-con left joypad connection Bluetooth pairing:
1、joy-con 手柄处于正常连接状态。
1. joy-con joypad is in normal connection.
2、进入设置”System Settings“-“Controllers and Sensors”-“Disconnect Controllers”断
开手柄自身蓝牙连接。
2. Go to settings "System Settings" - "Controllers and Sensors" - "Disconnect Controllers" to
disconnect the joypad's own Bluetooth connection.
3、长按手柄侧面“同步按钮”，直到手柄指示灯出现循环闪烁。
3, long press joypad side "synchronous button" until the joypad light cycle flash.
4、将 N100 Pro 与蓝牙适配器按照示意图连接至游戏主机。
4. Connect the N100 Pro and Bluetooth adapter to the game console according to the diagram.
5、等待 3-5 秒左右，手柄指示灯第一个灯常亮，游戏显示器上显示手柄连接成功并出现
“USB”提示，则连接成功。
5, wait about 3-5 seconds, you will see the joypad indicator light is always on, the screen show
joypad connection is successful and a "USB" logo, it means the connection is successful.

Pro 手柄连接蓝牙配对：
Switch Pro joypad connection Bluetooth pairing:
1、Pro 手柄处于正常连接状态。
1. Pro joypad is in normal connection.
2、进入设置“System Settings”-“Controllers and Sensors”-“Disconnect Controllers”断开
手柄自身蓝牙连接。
2. Go to settings "System Settings" - "Controllers and Sensors" - "Disconnect Controllers" to
disconnect the joypad's own Bluetooth connection.
3、长按手柄顶部“同步按钮”，直到手柄指示灯出现循环闪烁。
3. Press and hold the sync button on top of the joypad until the joypad indicator flashes in a
circle.
4、将 N100 Pro 与蓝牙适配器按照示意图连接至游戏主机。
4. Connect the N100 Pro and Bluetooth adapter to the game console according to the diagram.
5、等待 3-5 秒左右，手柄指示灯第一个灯常亮，游戏显示器上显示手柄连接成功并出现“USB”
提示，则连接成功。
5, wait about 3-5 seconds, you will see the joypad indicator light is always on, the screen show
joypad connection is successful and a "USB" logo, it means the connection is successful.
其他蓝牙手柄的连接方式也类似。
Other blue tooth joypad is similar way to connect.
N100 Pro 具有按键精灵、连招、一键连发、键位映射、线性控制、一键无线循环等多种功能，
还有多种游戏脚本进行选择，详细内容请进入官方网站（www.mycoov.com）查询。
N100 Pro has a variety of functions such as button wizard, continuous trick, one-button burst, key
map, linear control, one-button wireless loop, and a variety of game scripts. For details, please
visit the official website (www.mycoov.com). Com) query.

N100 Pro 有线连接示意图：
N100 Pro wired connection diagram:
连接设备（如连接示意图所示）
Connect the device (as shown in the connection diagram)
将 TYPEC OTG 线插入 SWITCH 充电口，COOV N100 Pro 插入此 TYPEC 线末端。手
柄通过手柄数据线连入 COOV N100 末端即可正常工作。
Insert the TYPEC OTG cable into the SWITCH charging port and insert COOV N100
Pro at the end of this TYPEC line. The handle is connected to the end of the COOV
N100 through the handle data cable to work normally.

固件、脚本更新
Firmware, script update
固件更新：
Firmware update:
1、进入官方网站（www.mycoov.com）
1. Enter the official website (www.mycoov.com)
2、点击产品列表 N100 Pro 的固件下载，将最新版本的固件压缩包下载至本地。
2. Click on the product list N100 Pro firmware download to download the latest
firmware firmware package to your local computer.
3、解压固件压缩包，找到固件文件中的“firmware.bin”文件。
3. Unzip the firmware package and find the "firmware.bin" file in the firmware file.
4、将 N100 Pro 插入电脑 USB 接口，将之前找到的“firmware.bin”文件“复制和替换”
进入 N100 Pro 的文件夹内。
4. Insert the N100 Pro into the computer's USB port, and copy and replace the
“firmware.bin” file found earlier into the N100 Pro folder.
5、N100 Pro 指示灯亮绿灯且自动弹出，则升级固件成功。（若亮红灯则失败，请重复步
骤）
5. The N100 Pro indicator lights green and pops up automatically. The firmware
upgrade is successful. (If the red light fails, repeat steps)

游戏脚本更新：
Game Script Updates:
1、进入官网网站（www.mycoov.com）
1. Enter the official website (www.mycoov.com)
2、点击游戏脚本页面，选择所需的脚本下载至本地。
2, click on the game script page, select the desired script to download to the local.
3、解压游戏脚本压缩包，找到脚本文件中的“data.bin”文件。
3. Decompress the game script archive and find the "data.bin" file in the script file.
4、将 N100 Pro 插入电脑 USB 接口，将之前找到的“data.bin”文件“复制和替换”进入
N100 Pro 的文件夹内。则更新成功。
4. Insert the N100 Pro into the computer's USB port and copy and replace the
“data.bin” file found earlier into the N100 Pro folder. The update was successful.

软件使用方式与 N100 一致，如下：
The usage mode of the software is the same as that of N100, as
follows:
A：线性控制（默认开启）
A：Linear control (on by default)
线性控制是用来关闭或开启手柄摇杆和扳机的线性响应，以实现更短的键程和更快的响应速
度
Linear control is used to turn off or turn on the linear response of the handle rocker
and trigger to achieve a shorter bond range and faster response speed.
1. 关闭线性
1. Turn off the linear
A. 同时按下 HOME+下键并松开，进入线性控制功能配置模式
A. Press the HOME+ Down button at the same time and release to enter the linear
control function configuration mode.
B. 将需要关闭线性功能的扳机按住不放，或拨动需要关闭线性功能的摇杆，再按一下中左
键，即可关闭对应扳机或摇杆的线性功能
B. Press the trigger that need to turn off the linear function, or dial the rocker that
need to turn off the linear function, and then click the Middle left button to turn off
the linear function of the corresponding trigger or rocker.
C. 按一下 HOME 键，退出配置模式
C. Press the HOME button to exit the configuration mode.

2. 开启线性
2. Turn off the linear
A. 同时按下 HOME+下键并松开，进入线性控制功能配置模式
A. Press the HOME+ Down button at the same time and release to enter the linear
control function configuration mode.
B. 将需要开启线性功能的扳机按住不放，或拨动需要开启线性功能的摇杆，再按一下中右
键，即可开启对应扳机或摇杆的线性功能
B. Press the trigger that need to turn on the linear function, or dial the rocker that
need to turn on the linear function, and then click the Middle right button to turn
on the linear function of the corresponding trigger or rocker.
C. 按一下 HOME 键，退出配置模式
C. Press the HOME button to exit the configuration mode.
3. 开启所有键位的线性
3. Turn on the linear of all buttons
A. 同时按下 HOME+下键并松开，进入线性控制功能配置模式
A. Press the HOME+ Down button at the same time and release to enter the linear
control function configuration mode.
B. 按住 HOME 键 3 秒钟，会自动开启所有线性功能，并自动退出配置模式
B. Hold down the HOME button for 3 seconds, then all the linear functions will be
turned on automatically, and it will exit the configuration mode automatically.

4. 支持的键位
4. Button supported
两个摇杆及两个扳机
Two rockers and two triggers
B: 键位映射
B: Button mapping
键位映射是将一个按键映射到另一个不同按键上，可实现多个按键相同功能或多个按键相互
交换的功能。
Button mapping is to map a button to another button, so as to realize the same
function of several buttons or exchange functions of several buttons.
1. 设置
1. Setting
A. 同时按下 HOME+右键并松开，进入键位映射功能配置模式
A. Press the HOME+ Right button at the same time and release to enter the button
mapping function configuration mode.
B. 按一下需要映射的按键
B. Press the buttons that need to be mapped
C. 按一下目标映射的按键
C. Press the mapping button

D. 按一下 HOME 键，退出配置模式
D. Press the HOME button to exit the configuration mode.
比如先按 A 键，再按 B 键，即使得 A 键具有 B 键功能。
For example, press the A button first and then press the B button, so that the A
button has the function of B button.
2. 单个清除
2. Single elimination
A. 同时按下 HOME + 右键并松开，进入键位映射功能配置模式
A. Press the HOME+ Right button at the same time and release to enter the button
mapping function configuration mode.
B. 按一下需要清除映射的按键
B. Press the button that needs to eliminate the mapping
C. 再按一下需要清除映射的按键
C. Press the button that needs to eliminate the mapping again
D. 按一下 HOME 键，退出配置模式
D. Press the HOME button to exit the configuration mode.
比如先按左键，再按一次左键，即使得左键恢复默认功能。
For example, press the Left button first, and then press the Left button once again,
so that the Left button will restore the default function.
3. 全部清除
3. Elimination
A. 同时按下 HOME+右键并松开，进入键位映射功能配置模式

A. Press the HOME+ Right button at the same time and release to enter the button
mapping function configuration mode.
B. 按住 HOME3 秒钟，会自动清除所有已配置的键位映射，并自动退出配置模式
B. Hold down the HOME button for 3 seconds, all the configured button mappings
will be eliminated automatically, and it will exit the configuration mode
automatically.
4. 实例 1
4. Examples1
A.先将 A 键映射为 B，再将 B 键映射为 A，即可实现两键交换
A. First map the A button to B, and then map the B button to A, so that the two
buttons can exchange function.
(在键位映射模式下，实现方法为按 A B B A）
(In the button mapping mode, the operation is to press A, B, B, A)
B. 将 A 键映射为 B，再将 B 键映射为 X，再将 X 键映射为 A，即可实现三键交换；以此类
推
B. Map the A button to B, map B to A, and then map X to A, so that the three
buttons can exchange function; and so forth
(在键位映射模式下，实现方法为按 A B B X X A）
(In the button mapping mode, the operation is to press A, B, B, X, X, A)
5. 实例 2

5.Examples 2(exchange touchpad and SHARE)
(Firmware version is not less than V3.4006)
A. In this configuration process, double-click HOME can not be simulated into
other keys, so you need ps4 handle or pro handle for this operation
B. Enter key mapping function configuration mode, press the middle left touch
pad / screenshot key touch pad / screenshot left key, then press HOME to exit
6. 支持的键位
6. Button supported
除 HOME 键及摇杆外的所有按键
All buttons except the HOME button and the rocker
C：连发（默认关闭）
C: Burst (off by default)
连发控制是用来将选定的按键配置为连发模式，当按键处于连发模式下，该键被按下后，就
会以一定频率模拟按下-松开-按下-松开事件，连发频率可调
Burst control is used to configure the selected button to a burst mode. When the
button is in a burst mode, once it is pressed, it will simulate the pressing-releasing
event at a certain frequency, and the frequency is adjustable.
1. 开启连发

1. Turn on the burst
A. 同时按下 HOME+左键并松开，进入连发功能配置模式
A. Press the HOME+ Left button at the same time and release to enter the burst
function configuration mode.
B. 将需要开启连发功能的按键按住不放，再按一下中右键，即可开启对应按键的连发功能
B. Hold down the button that needs to turn on the burst function, and then press
the Middle right button, so that the burst function of the corresponding button can
be turned on.
C. 按一下 HOME 键，退出配置模式
C. Press the HOME button to exit the configuration mode.
2. 关闭连发
2. Turn on the burst
A. 同时按下 HOME+左键并松开，进入连发功能配置模式
A. Press the HOME+ Left button at the same time and release to enter the burst
function configuration mode.
B. 将需要关闭连发功能的按键按住不放，再按一下中左键，即可关闭对应按键的连发功能
B. Hold down the button that needs to turn off the burst function, and then press
the Middle left button, so that the burst function of the corresponding button can
be turned off.
C. 按一下 HOME 键，退出配置模式
C. Press the HOME button to exit the configuration mode.

3. 清除所有连发
3. Elimination of all the burst
A. 同时按下 HOME+左键并松开，进入连发功能配置模式
A. Press the HOME+ Left button at the same time and release to enter the burst
function configuration mode.
B. 按住 HOME3 秒钟，会自动清除所有已配置的连发功能，并自动退出配置模式
B. Hold down the HOME button for 3 seconds, all the configured burst function will
be eliminated automatically, and it will exit the configuration mode automatically.
4. 调整连发频率（基本模式）
4. Adjust the burst frequency(Basic mode)
A. 同时按下 HOME+左键并松开，进入连发功能配置模式
A. Press the HOME+ Left button at the same time and release to enter the burst
function configuration mode.
B. 按一下十字方向键上，即可加大连发频率
B. Press the Up of the cross button to Increase the burst frequency
C. 按一下十字方向键下，即可降低连发频率
C. Press the Down of the cross button to reduce the burst frequency
D. 按一下 HOME 键，退出配置模式
D. Press the HOME button to exit the configuration mode.

5. 调整连发频率（自定义模式）
5. Adjust the burst frequency(Custom mode)
(Firmware version not less than V4.1001)
In custom mode, the user can set two parameters: press time a millisecond and
release time b milliseconds. When the burst starts, the key is automatically pressed
for a millisecond, then released for b milliseconds, and then pressed a millisecond
for a round trip. The values of a and b should be greater than 4 and less than 252.
A. Determine the value you want to set, such as a is 128, b is 164
B. Press the HOME + function button at the same time left and release, enter the
serial configuration mode
C. Hold down the middle left button and right button, and do not release
D. set a value: press the function key, the value of a increase of 100; press the right
two function keys, a value increased by 20; press the eight function keys, a value
increased by 8. Total 128
E. Set the b value: Press the cross key, the value of b increases by 100; press the six
lower cross key right, the b value increases by 60; press the four lower cross key, the
b value increases by 4. Total 164
F. release the middle and left and right button, the normal configuration, it will flash
green light.
G. If there is a configuration error during step 2 through step 6, you can reconfigure

from step 2. A value and b value can also be set separately.
H. Press the HOME key to exit the configuration mode
6.支持的键位
6. Button supported
除 HOME 键、中左键、中右键及摇杆外的所有按键
All the buttons except HOME button, the Middle left button and the Middle right
button and the rocker
D：一键连招
D: Auto combo
在格斗游戏中，往往一个大招需要按照一定规律连续操作手柄。一键连招功能可以将这个连
招动作记录下来，并设置成通过某个按键触发，设置完成后，玩家即可一键连招
In the fighting games, an ultimate skill often needs to operate the handle in a
certain rule. The auto combo can record the combo and set to trigger by a certain
button. After the setting, the player can use the auto combo.
1. 设置
1. Setting
A. 同时按下 HOME+上键并松开，进入一键连招功能配置模式
A. Press the HOME+ Up button at the same time and release to enter the auto
combo function configuration mode.