COP Security 15-2400DT User manual

1
2.4GHz Digital Wireless A/V/Data Transmitter and Receiver KIT
USER MANUAL
MODEL: 15-2400DK
1. Key Features
Offer a wireless link solution audio/video/data signals connection.
2.4 GHz frequency hopping spread spectrum module and supported max. 25 Auto
hopping channels for resisting interferences to other 2.4G devices.
100mW RF output (Average).
Point to point mode only.
MPEG-4 (D1) standard video compression and stereo audio inputs.
5-bit ID pairing key for security.
Max. 250 meters (light-of-sight)
2. Panel View 15-2400DT
15-2400DR
①. DC 12V IN: DC 12V power input.
②. RS-485 I/O: 2-wire half-duplex RS-485 supported.
③. AUDIO I/O: RCA female connectors for the stereo audio signal.
④. VIDEO I/O: BNC female for the analog CVBS video signal.
⑤. POWER ON or RF LINK LED:
Indications Power/RF LINK LED
Power On On
RF Link Loss Low Flashing
⑥. RS-485 LED: Indicated to RS485 data are transmitted or received
⑦. ID Setting: ID setting is use for paring with 15-2400DK transmitter and receiver each other.
It must be make a same ID code first before you setup the devices.
⑧. BAUD RATE and TERMINATION: Baud rate and 120 Ohm termination setting by DIP switch.
(Note: After changing the baud rate setting by DIP switch, please re-boot the device again.)
⑨. ANT: SMA connector for connected to 2.4 GHz antennas.
○
1○ 2○
3○
4○
5○
6○ 9○ 7○
8

2
3. Quick Installation
3.1 To set the same ID code with Transmitter and Receiver each other by 5-bit DIP switch.
3.2 To set the same Baud Rate with Transmitter and Receiver each other by 2-bit DIP switch.
3.3 Plug the Video and Audio signals to the BNC and RCA connectors.
3.4 Plug the 2.4G Antenna to SMA connector.
3.5 Please check +12VDC input, then power on the devices.
REMARK: Avoid the frequency channels have the interference; please don’t close to the 802.11 a/b/g/n AP
routers and other 2.4GHz devices.
4. Caution for Installation
4.1 Be careful; never let any water in this equipment.
4.2 If necessary, use a soft cloth moistened with alcohol to wipe off the dust.
4.3 Be extra careful not to shake the unit.
4.4 Avoid places where temperatures exceed 50°C or higher.
4.5 Avoid places where there are frequent vibrations or shocks. When any abnormalities occur, make sure to
unplug the unit and contact your local dealer.
5. Packing
5.1 Transmitter ×1
5.2 Receiver ×1
5.2 Antenna 5dBi ×2
5.3Usermanual ×1
5.4 Screws ×8
5.5 Plastic-Conical-Anchor ×4
5.6 Power Adaptor ×2 [Option]
6. Specification
Items / Models 15-2400DT 15-2400DR
RF
Frequency Channels 2400 ~ 2480 MHz, 25-CH Auto Hopping
(FCC & CE RTTE)
RF TX Power 100mW (Average) --
Modulation 16-QAM,QPSK,BPSK
Min. RX Sensitivity -- -80dBm
RF Impedance 50Ω50Ω
Distance vs. Frame Rate 250 Meters: 15 ~25 fps(NTSC) / 13 ~21 fps(PAL)
150 Meters: 20 ~30 fps(NTSC) / 17~25 fps(PAL)
100 Meters: 30 fps(NTSC) / 25 fps(PAL)
Video
Video Compression MPEG-4
Max. Frame Rate
vs. Resolution
NTSC: 30 fps at 720 × 480 (D1)
PAL: 25 fps at 720 × 576 (D1)
Bit Rate Up to 6Mbps
Audio
Sampling Rate 48KHz, Stereo
S/N Ratio 63dB
Data
RS-485 2-wire RS-485 Half Duplex
Baud Rate: 2400/4800/9600 bps
Fixed Formats:1 Start bit, 1 Stop bit, 8 Data Bits, No Parity
120 Ohm Termination Resistor ON/OFF Setting
LED Indicators
Red LED Power On and RF Link Status
Green LED RS-485 Data Link Status
Mechanical & Environmental
Power Consumption 230 mA @ 12VDC 230 mA @ 12VDC
Operation Temp. -10°C ~ 50°C
Storage Temperature -30°C ~ 85°C
Dimensions
(without Antenna)
118 ×75 ×25 mm
Weight (without antenna) 237 g 235 g

3
FCC Part 15 Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
3. Any changes or modifications (including the antennas) made to this device that are not expressly
approved by the manufacturer may void the user’s authority to operate the equipment.
Q2012/02/20