Corbin H-18-GW-LID User manual

Part Number: H-18-GW-LID
Description: Trunk Lid
Fitment: 2018 - 2020 Honda Gold Wing 1800 Tour
Revision: 2
Tools Required Parts List
Phillips Screwdriver
3/32Allen Wrench
4mmAllen Wrench
For Luggage Rack Installation:
Masking Tape
Blade
3/4 Hole Saw and Drill
10 #SP00974 6mm x 16Allen Bolts
6 #SP00285 1/4” Lock Washers
10 #SP01080 6mm Flat Washers
10 #SP00201 8-32 x 1/2 Button HeadAllen Bolts
10 #SP00217 #8 Flat Washers
2 1” x 2” Soft Stick on Velcro
1 12” Zip Tie
FIG 4 FIG 5
FIG 2 FIG 3
FIG 1
1. Remove the trunkrest pad by removing six
Phillips screws (Figure 1), then lift up the trunk-
rest pad and unplug (Figure 2).
2. Disconnect the three clamps on the wire
harness keeper by squeezing the clamp and then
push out through the hole (Figure 3).
3. If you have the optional trunk light, remove it
from your OEM trunk. See owner’s manual if
necessary.
4. Tape together the end of the trunk light wire to
the provided zip tie (Figure 4).
5. Route the zip tie down through the hole in the
Corbin trunk lid (Figure 5) and pull out through
the other side of the lid (Figure 6). Remove the
zip tie.
6. Secure the light housing to the Corbin trunk,
using the suppliedAllen bolts and flat washers
(Figure 7).
7. If you haven’t done so aleady, remove the
trunk lid by removing the sixAllen bolts (three on
each side), using a 6mmAllen wrench (Figure 8).
NOTE: Open lid and remove the last bolts on
each side because the lid may spring up on you.

FIG 6 FIG 7
FIG 8 FIG 9
FIG 11
FIG 10
8. Remove the catch brackets on the OEM lid
with a Phillips screwdriver and install them on the
Corbin trunk lid, using the suppliedAllen bolts and
flat washers (Figure 9).
OPTIONAL LUGGAGE RACK INSTALLATION:
9. Tape the top of the trunk with painters tape
where you will be drilling holes for the luggage
rack (Figure 10).
10. Turn the lid upside down and drill four holes,
using a drill bit smaller then the hole, making sure
the drill is perpendicular (Figure 11).
11. Turn the lid back over, cut the circle on the
provided template, center the template over the
holes you just drilled and mark the position
(Figure 12).
12. Place the trunk rack on top, to make sure the
holes align with the trunk rack. Make adjustments
if necessary (Figure 13).
13. Score the paint with a blade or sharp object
(Figure 14).
14. Next you will be using a 3/4” hole saw. Place
two supplied washers onto the drill bit and then
add the hole saw (Figure 15).
NOTE: You don’t want more then a 1/4” of the
drill sticking out past the hole saw (Figure 16).
15. Drill out the holes slowly and carefully,
making sure to NOT drill on the bottom side
(Figure 17).
NOTE: Make sure the drill bit is on tight, so it
doesn’t wobble.
16. Gently remove the tape by pulling all four
ends towards the hole to prevent any paint from
lifting with the tape (Figure 18).

FIG 12
FIG 15
FIG 16
FIG 13 FIG 14
FIG 17
17. Place the rubber grommets through the holes
you just drilled, making sure the top hole with
parting line on the grommet is facing towards the
center of the trunk lid (Figure 19).
18. Put lubricant on the holes on the rubber
grommets.
19. Align the pegs on the trunk rack to the holes
on the rubber grommets.
20. Flip the trunk lid and trunk rack over and
secure the trunk rack with the supplied 6mmAllen
bolts and 6mm flat washers (Figure 20). Use a
mild strength loctite®.
21. Install the Corbin trunk lid by using the
supplied 6mm x 16mmAllen bolts, lock washers
and flat washers (three bolts on each side). Do
Not Tighten. (Figure 21)
22. Pull the trunk light wire harness through both
holes on the trunk (Figures 22 & 23).
23. Secure the trunk light wire harness with the
supplied velcro (Figure 24), then plug the wires
(Figure 25).
24. Re-install the OEM trunk rest or Corbin trunk
rest.
1/4”

Questions? Give us a holler...
800-223-4332
[e-mail]
FIG 18 FIG 23
FIG 20
FIG 21 FIG 17FIG 22
FIG 25
FIG 19 FIG 24
CUT OUT
3/4”
Actual
Size