Coremorrow E52 Series User manual

E52 Series Piezo Controller
User Manual
Version: V1.0
This document describes the following products:
E52.B1S-H Servo piezo controller(standard version)
E52.B1S-I Servo piezo controller(simplified version)
E52.A1K-H Open loop piezo controller

声明
Declaration!
This user manual is a integrated user manual of the E52 series piezoelectric controller. Please
read this user manual carefully before using this controller. Follow the instructions in the manual
during use. If there is any problem, please contact us for technical support. If you do not follow
this manual or disassemble and modify the product yourself, the company will not be liable for any
consequences arising therefrom.
Please read the following to avoid personal injury and to prevent damage to this product or any
other product connected to it. In order to avoid possible hazards, this product can only be used
within the specied range.
Notice!
Do not touch any exposed ends of the product and its accessories.
There is high voltage inside. Do not open the case without permission.
Do not connect or disconnect input, output, or sensor cables with power on.
Please keep surface of E52 clean and dry, don't operate in humid or static environment.
After use, output voltage should be cleared to zero before turning o󰀨 the controller switch, such as
switching the servo state to the open-loop state.
Danger!
The piezoelectric power amplier described in this manual is a high-voltage device capable of
outputting high currents, which can cause serious or even fatal damage if not used properly.
It is strongly recommended that you do not touch any parts that connect to the high voltage output.
Special Note: If you connect it with other products in addition to our company, please follow the
general accident prevention procedures.
Operating the high-voltage amplication requires training professional operators.
Cautious!
Warning!
If the voltage exceeds the PZT's tolerable range, it will cause permanent damage to the PZT.
Before adding voltage to the PZT poles, it must be ensured that the positive and negative poles
of the PZT are connected correctly and the operating voltage is within the allowable range of this
PZT.
E52 housing should be installed on a horizontal surface in an area with a 3CM air ow area to
prevent internal convection in the vertical direction.
Insu󰀩cient airow can cause equipment to overheat or premature instrument damage.
DECLARATION

1
1.Security ………………………………………………………………………………………………………………………… 2
1.1 Features ………………………………………………………………………………………………………………… 2
1.2 Applicaitons …………………………………………………………………………………………………………… 2
1.3 Order information…………………………………………………………………………………………………… 2
2. Driving Principle ………………………………………………………………………………………………………… 2
3.Appearance ………………………………………………………………………………………………………………… 3
4. Frequency Load Curves ……………………………………………………………………………………………… 4
5.Interface ……………………………………………………………………………………………………………………… 4
6.Power Calculation ………………………………………………………………………………………………………… 5
7. Notes and Suggestions ……………………………………………………………………………………………… 6
8. Maintenance, Storage, Transportation ………………………………………………………………………… 6
8.1 Cleaning Measures ………………………………………………………………………………………………… 6
8.2 Transportation and Storage …………………………………………………………………………………… 7
9. Service and Maintenance …………………………………………………………………………………………… 7
9.1 Disposal ………………………………………………………………………………………………………………… 7
9.2 After-sales Service ………………………………………………………………………………………………… 8
10.Contact us…………………………………………………………………………………………………………………… 8
Contents

2
E52 Series Piezo Controller User Manual
1.Security
1.1 Features
High power (50W)
Peak current (Higher than 17A)
Optional sensor closed loop module
Combination of active and passive heat dissipation
Over-temperature protection
1.2 Applicaitons
Piezo spot rubber valve
Piezo drives with large electrostatic capacity and requiring rapid response
1.3 Order information
E52.B1S-H—SGS sensor clsoed loop standard version ,1 channel piezo controller
E52.B1S-I—SGS sensor clsoed loop simplified version ,1 channel piezo controller
E52.A1K-H—Open loop, 1 channel piezo controller
Accept customized according to requirements：
① 12bit gain/-20 ～ 120V output voltage（standard version）
② 15bit gain/-20 ～ 150V output voltage
2. Driving Principle

3
3.Appearance
Front Panel Rear Panel
Side Inlet
Top Heat Dissipation Drawing
Side Outlet

4
E52 Series Piezo Controller User Manual
4. Frequency Load Curves
5.Interface

5
No. Functions Description
①Power indicator Green, lights when power's on
②Overcurrent
indicator
Red, lights when the output current exceeds the rated
value
③Analog input Analog voltage input interface
④Potentiometer Parameters adjustment(sensing zero, offset, gain)
⑤Sensor monitor Detect sensor output, voltage range 0~10V
⑥Sensor Sensor input
⑦PZT Voltage output interface
⑧Servo Open/closed loop switch
6.Power Calculation
● Average output（Sine wave operation mode）
Pa ≈ Upp • Us • f• Cpiezo
Pa=Average output[W]
Upp=Peak and peak drive voltage [V]
Us=Drive voltage[V]（（Vs+）-（Vs-））
Cpiezo=Piezo actuator capacitance[F]
f=Operating frequency of the sine wave[Hz]

6
E52 Series Piezo Controller User Manual
7. Notes and Suggestions
When the power used is large or the ambient temperature is high, external auxiliary
heat dissipation can be considered.
The temperature of the over-temperature power off protection is 75±5 ℃ , but this
function should be used as the protection against accidents under the limit condition. When
in normal use, please try to keep the top heat dissipation shell below 55℃ .
When the step amplitude is less than 3V, the peak current is small, less than 0.5A. As
the step amplitude increases, the peak current also increases.When the step amplitude is
greater than 10V, the peak current is greater than 17A.
When the output power is too large or the output is short circuited to the ground,
the overcurrent indicator will light up, and the power supply part will output with a smaller
cross-current.When the short circuit or power output is withdrawn, the overcurrent indicator
goes out and the power supply returns to normal. But do not overflow for a long time.
E52 cannot be used to drive inductive loads. If the inductive loads are driven, the
product may be damaged.
If there is no need, please do not twist the potentiometer easily.
8.1 Cleaning Measures
Note! The PCB board of the function module in the E52 is an ESD (electrostatic discharge)
sensitive device. Take precautions against any static build-up of these devices before use to avoid
contact with circuit component leads and PCB wiring. Before touching any electronic components,
the body rst touches the grounding conductor to discharge static electricity, ensuring that any
type of conductive particles (metal, dust or debris, pencil lead, screws) enter the device. Be
careful not to drop the equipment when cleaning, to avoid any form of mechanical shock!
Disconnect the power plug of the E52 system before cleaning.
Prevent cleaning fluid and any liquid from entering the system module to avoid short
8. Maintenance, Storage, Transportation

7
circuits.
The surface of the system chassis and the front panel of the module, please do not use an
organic solvent for surface wiping.
8.2 Transportation and Storage
This product is packed in carton. Transportation must be carried out under product
packaging conditions, and direct rain and snow, direct contact with corrosive gases and strong
vibrations should be avoided during transportation.
The instrument can be transported under various conditions of normal transportation, and
should avoid damp, load, collision, extrusion, irregular placement and other adverse conditions
during transportation.
If the instrument is not used for a long time, the instrument should be packaged and
stored.
The instrument should be stored in a non-corrosive atmosphere and in a well ventilated,
clean room.
In the process of transportation, storage and use, attention should be paid to fire
prevention, shockproof, waterproof and moisture proof.
Note: Pay attention to frost when the E52 series piezo controller is powered on in winter to avoid
burning the controller!
Check whether the controller has frost before power on (frost usually occurs when moving
from outdoor to indoor).
If the controller is frosted, wipe it or dry it and store it indoors for more than two hours
before powering it up for relevant operation.
9. Service and Maintenance
9.1 Disposal
When disposing of old equipment, please abide by the national regulations and local
regulations.Please dispose of the old equipment properly.Please contact CoreMorrow for
the upgrade and replacement of old equipment in order to meet the customer's handling of
system products.

8
E52 Series Piezo Controller User Manual
10.Contact us
Harbin Core Tomorrow Science & Technology Co., Ltd.
Tel: [phone]
Email: [e-mail]
Website: www.coremorrow.com
Address: Building I2, No.191 Xuefu Road, Nangang District, Harbin, HLJ, China
CoreMorrow Official and CTO WeChat are below:
If you have an old device or an unusable device that cannot be handled, you can ship
it to the following address:
Address: 1F, Building I2, No.191 Xuefu Road, Nangang District, Harbin, Heilongjiang
9.2 After-sales Service
E52 does not contain user repairable components.
E52 must be returned to factory for any service and repair.
Any part of E52 is dismantled, there will be no warranty service.
E52 is a precision instrument which should be handled with care.
In case of any problem, please record the problem and contact CoreMorrow to be
repaired by professional technicians.