Cornell CBL-E500GM User manual

User Manual
Blender CBL-E500GM

3
IMPORTANT SAFEGUARDS
2
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE
• Before using the appliance, ensure that the power supply voltage corresponds to the
voltage indicated on the rating plate at the bottom of the appliance.
• In order to avoid electric shocks and other personal injuries, do not immerse the
appliance or other components such as power cord, power plug and motor base into
water or other liquids.
• This appliance is intended for household use only. Any other use is considered improper
and thus dangerous.
• Never allow this appliance to be used by persons (including children) with psychological,
physical or sensory impairments or with insufficient knowledge, unless closely
supervised and instructed by someone responsible for their safety. Always supervise
children and ensure they do not play with the appliance at all times.
• Never leave the appliance unattended while it is in operation.
• Never place hands into the blender jar when it is plugged into the power supply.
• Always operate the blender with the cover in place.
• Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions, or is dropped or damaged in any manner. Return appliance to nearest
Customer Service Center (see Warranty for details) for examination, repair, and/or
mechanical or electrical adjustment.
• Always operate the blender with the cover in place.
• Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions, or is dropped or damaged in any manner. Return appliance to nearest
Customer Service Center (see Warranty for details) for examination, repair, and/or
mechanical or electrical adjustment.
• Do not allow power supply cord to hang over edge of table or counter, or touch hot
surfaces.
• Do not operate the blender empty as it could damage or cause the appliance to
malfunction.
• Do not attempt to disassemble or modify the appliance or repair the power cord in any
event of a malfunction. If it is damaged or needs replacing, contact your nearest
Customer Service Centre or any similarly qualified technician in order to avoid a hazard.
• Always switch off and unplug appliance from the power supply when not in use, before
attaching or detaching moving parts or accessories, and before cleaning or removing
contents from the blender jar.
• BLADES ARE VERY SHARP. HANDLE CAREFULLY. Exercise caution when handling the
blender’s sharp cutting blades, especially when emptying the bowl and during cleaning.
Store out of children’s reach.
• CAUTION: Ensure that the blender is switched off before removing it from the stand.
• Exercise caution when hot liquid is poured into the blender as hot steam can escape
from the blender jar.
C O N T E N T S
IMPORTANT SAFEGUARDS
PARTS IDENTIFICATION
SPECIFICATIONS
IMPORTANT NOTES
OPERATING INSTRUCTIONS
SAFETY POWER CUT-OFF FEATURE & SAFETY BUILT-IN SWITCH
3
4
4
5
5-7
7

5
IMPORTANT NOTES
OPERATING INSTRUCTIONS
4
PARTS IDENTIFICATION
SPECIFICATIONS
• Never fill the blender jar with ingredients hotter than 65.
• Always ensure the lid is correctly assembled on the jar and the measuring cup is inserted
properly in the lid before powering on the appliance.
• Do not exceed the maximum indicator line of the blender jar when filling water and other
liquids.
• Always turn off the appliance and remove the power cord from the power supply after
every use.
• After blending has completed, allow hot foods to adjust to the room temperature before
serving
• Always keep the blender clean and dry after using.
• Please refer to the illustrations
• Ensure ingredients sizes do not exceed 2cmX2cmX2cm
•OPERATION TIME: Do not operate the blender more than 1 minute consecutively. Leave
the appliance to cool for 10 minutes before every re-use.
•CAUTION: If the blender gets stuck, cease operating blender immediately and remove
the obstruction.
•GRINDING TIME: Do not operate for more than 25 seconds each time. Ensure coffee
beans do not exceed the 30-80g. "Max" mark on the grinding cup. Allow a minute
interval before successive operating the blender again in order to prevent the appliance
overheating.
•CAUTION:
a) If the grinding blade is operating without grinding any food, power off and unplug
from the power supply, disassemble the grinding cup, shake the food and begin the
grinding function again
b) After grinding is finished, do not remove the grinding cup until the motor stops
• Use the following food test: carrot size less than 1.5cm x 1.5cm x 1.5cm with water
according to the rate (carrot 2:3 water) together. Ensure the total capacity does not
exceed 1.5L.
• Pour approx. 400–700ml water into the jar. Ensure the lid covers the jar properly and use
function ‘P’ for a few seconds after using.
1. Measuring cup
2. Lid
3. Blender jar
4. Chopping blades
5. Measuring cup
6. Lid
7. Glass blender jar
8. Chopping blades
9. Grinding cup
10. Grinder units
11. Main body
12. Control knob
MODEL NO. CBL-S250M
RATED VOLTAGE / FREQUENCY 220-240V~ 50/60Hz
RATED WATTAGE 400-450W
CAPACITY 1500m

7
OPERATING INSTRUCTIONS
SAFETY POWER CUT-OFF FEATURE & SAFETY BUILT-IN SWITCH
6
OPERATING INSTRUCTIONS
After blending has completed, adjust the control
knob switch to‘0’ position. Remove power plug
from power supply. Detach the blender jar
according to diagram.
• This blender is fitted with a safety power cut-off feature which safeguards against
excessive loads. In case of overloading, the blender will automatically activate the safety
power cut-off protection and operation will come to a stop. If this occurs, set the knob
to FF position, unplug the appliance and let it cool down to room temperature before
attempting to operate it again.
• The Safety built-in switch ensures that the appliance would only operate if the blender
jar is assembled correctly with main body.
SERVICE: Please co tact with your earest customer service or authorized sales
age t for repair or service.
Put the Silicone sealing onto
the blender blade unit
according to the diagram( r
remove for the cleaning. Ex-
factory goods have been fitted
to the blender units.)
Fit the blender blade unit onto
the blender jar according to the
diagram. Assemble the lid onto
the jar. Insert the measuring
cup properly into the food
chute. (Note: the size of the
mixing ingredients should be
less than 2cm x 2cm x 2cm).
Assemble the blender jar with
the food onto the main body.
Plug in power plug into
power supply and turn the
control knob according to
desired speed.
After blending has completed,
adjust the control knob switch
to‘0’ position. Remove power
plug from power supply.
Deta c h t h e b l e n der jar
according to diagram.
Place dry grinding food into
the grinding cup. Assemble the
grinder unit according to the
diagram. Do not exceed the
"Max" mark on the grinding
cup.
Assemble the blender jar with
the food onto the main body.
Plug in power plug into power
supply and turn the control
knob according to desired
speed.