CORNING SCRN-530 Manual

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 1Small Cell Radio Node - SCRN-530 Hardware Installation GuideDOC-SCRN-530-HIGIssue 1Related Literature | Search www.Corning.com/opcomm. Click Required Resources.Table 1 Revision HistoryIssueDateSummary of Changes121JUL21First issue for SCRN-530 Small Cell Radio Node.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 2Table of ContentsFCC Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Other Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Section 1.System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Section 2.Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Section 3.Radio Node Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Section 4.SCRN-530 Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Section 5.Connectors, SFP+ and Micro-USB Ports, and Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.1Phoenix Power Cable Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.2SFP+ Transceiver Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.3Micro-USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.4Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Section 6.System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Section 7.Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Section 8.Mounting the SCRN-530 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118.1Installing the SCRN-530 on a Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118.2Installing the SCRN-530 on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Section 9.Cabling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Section 10.Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Section 11.Detaching the SCRN-530 from the Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Section 12.SCRN-530 LED Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Section 13.SCRN-530 LED Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Section 14.Disabling the LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Section 15.Re-Enabling the LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Section 16.SFP+ LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Section 17.Corning Documentation Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 3FCC StatementsSafety PrecautionsCorning strongly recommends reviewing and adhering to the following cautions and notices before installing and operating the SCRN-530. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.RF Exposure Warning Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 40 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.This device can be expected to comply with part 15 of the FCC Rules provided it is assembled in exact accordance with the instructions provided with this kit. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.WARNING: This warning symbolizes danger that may cause severe injury or death. Before installing or servicing equipment ensure that you are aware of all hazards involved with electrical circuitry and become familiar with applicable safety standards and national and local electrical codes and any other relevant standards.WARNING: For Professionals & Trained Installers:• The device is designed for wall mount or ceiling mount applications only in an enterprise environment.• Installers are required to maintain RF safety distances of 40 cm during the course of installation process.• Wall installation should be avoided, if a minimum safety distance of 40 cm cannot be maintained. WARNING: All electrical equipment must be properly grounded. Refer to national and local electrical codes and any other relevant standards for electrical grounding information.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 4Other CautionsCAUTION: ESD can damage the SCRN-530 and internal components. Ensure that the SCRN-530 and associated antenna equipment is installed and serviced according to national and local ESD standards.CAUTION: Do not open the SCRN-530 casing. E-RAN wireless system equipment must only be serviced by Corning-accredited personnel. Opening the SCRN-530 casing voids the warranty.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 51.System OverviewThe Corning SCRN-530 small cell radio node is a high-performance integrated 5G new radio (NR) mmWave small cell that is part of the Corning enterprise radio access network (E-RAN). The scalable SCRN-530 radio node and the enterprise radio access network (E-RAN) simplify the complexity of radio management and mobility, and provide operators with a single touchpoint to aggregate and manage a large network of 5G small cells. This guide provides the system specifications of the SCRN-530. It includes detailed hardware installation instructions, the boot sequence, and expected LED behavior both during the boot-up and under normal operating conditions. NOTE:The SCRN-530 small cell radio node is referred to as “radio node” in the rest of this document.NOTE:The 5G New Radio (NR) is a new radio access technology developed by 3GPP for fifth generation (5G) mobile networks.The primary audience for this guide includes network planners, system administrators and installation personnel. It assumes you have knowledge about networking principles, networking configuration, site preparation, powering, and experience in hardware installation and maintenance.2.Product OverviewThe SCRN-530 is a 5G mmWave Time Division Duplexing (TDD) radio node that supports 2 x 2 MIMO small cell operation on NR band n260, enabling high user capacity and high data rates for the coverage footprint. The radio node connects to a Corning centralized unit (CU). It uses certificate-based authentication with the Corning CU. Radio Nodes are managed by the Corning centralized units installed in the enterprise or in a centralized location such as a data center. The SCRN-530 includes built-in self-organizing networks (SON) features for ease of deployment. Its fronthaul network can be deployed using approved 10 Gb fiber optic cables. The SCRN-530 receives 48 VDC power from a Corning PSU6 DC Power Supply Unit or equivalent. There is no management or console port on the SCRN-530, and the radio node is physically locked to prevent theft. The SCRN-530 is passively convection-cooled, and its antennas are built-in. Each SCRN-530 comes with a ceiling-mount bracket attached for installing directly to a flat surface, as well as a second multi-angle (0, 15, 30, and 45 degree) wall-mount bracket loose in the box. The SCRN-530 uses on-chip Trusted Platform Module (TPM) functions to implement secure boot, and to establish certificate-based IPsec tunnels to the centralized unit. It

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021| Page 6includes a PTP client to achieve frequency and phase synchronization with other mmWave radio nodes and base stations. The E-RAN element management system includes configuration, fault and performance monitoring, and security functions. Figure1 shows the architecture of the 4G and 5G E-RAN network.Figure 14G and 5G E-RAN Architecture3.Radio Node ModelTable1 includes the SCRN-530 model configuration.Table 1 Radio Node ConfigurationRadio Node ModelDescriptionAntenna TypeSCRN-530-3939 GHz band n260 mmWave RN with 8 x 8 dual-polarization antenna arrayInternal
Email Web
DMZ
Enterprise
Mobile
Operator
Core
SCRN-530
Radio
Nodes
5G RN
Fronthaul
Core
Switch
Firewall
Security
Gateway
5G
EN-DC
UEs
PSU6
5G Centralized
Unit (CU)
NR
(5G)
DC
Power
10G
Connections
4G RN
Fronthaul
PoE+
Switch
4G Services
Node (SCSN)
4G and 5G EN-DC RAN
LTE
(4G)
CU IPsec
Backhaul
S1-U
3GPP
GTP Tunnel
4G
Radio
Nodes
1G
Connections
SCSN IPsec
Backhaul
3GPP
Tunnel
X2
4G
UEs

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 74.SCRN-530 ViewsFigure2 and Figure3 display views of the SCRN-530.Figure 2SCRN-530 CoverFigure 3SCRN-530 With Ceiling-Mount Bracket

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 85.Connectors, SFP+ and Micro-USB Ports, andStatus LEDThe SCRN-530 has connectors and a small form-factor pluggable SFP+ port, as shown in Figure4.Figure 4SCRN-530 Connectors and Status LED5.1Phoenix Power Cable PortThe SCRN-530 has a 48 VDC power connector for delivering power from a Corning PSU6 DC Power Supply Unit or equivalent to the radio node. Plug the Phoenix power connector from the power source cable into the power connector.5.2SFP+ Transceiver PortThe SFP+ Transceiver Port accommodates a compact enhanced small form-factor pluggable (SFP+) network interface module. The hot-pluggable SFP+ supplied with this SCRN-530, must be installed in the Transceiver Port. The LC connector, terminated end, of the fiber pair of an ActiFi cable (or other approved fiber cable) is then connected to the SFP+ LC Ports to provide fronthaul transport network access to the radio node. Refer to Section 16. SFP+ LED Indications for more information.5.3Micro-USB PortThe Micro-USB port is completely disabled and is not available for general use.5.4Status LEDThe STA (status) RGB tri-color LED indicates the state of the SCRN-530, with boot, normal, disabled, fault, and SCRN-530 indications. When the radio node initially boots, the LED cycles through a number of colors and flashing behaviors until the radio node is fully operational. Section 12. SCRN-530 LED Boot Sequence describes the STA LED indications.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021| Page 96.System SpecificationsThe SCRN-530 has the chassis measurements, power requirements, and environmental requirements, and complies with the standards listed in Table2. Refer to the feature guide for your centralized unit software release for release-specific features and specifications.Table 2 SCRN-530 SpecificationsOperating Band2 x 2 MIMO operation on 39-GHz NR band n260 (37.0 – 40.0 GHz)Channel SizeComponent Carrier (CC) bandwidth: 100 MHzAntenna Type8 x 8 dual-polarization internal antenna arrayAntenna Power43 dBm EIRP @ 64QAMBeamforming scan range: +/- 60 degreesRF ManagementBeam Management with auto-assignment of physical cell identities (PCIs)QoS FeaturesNon-GBR bearer support per UEDimensions279.4 x 279.4 x 80.3 mm (11.0 x 11.0 x 3.16 in)Weight4.5 kg (9.9 lbs)Input Power1 x 48 VDC Phoenix, deliverable using Corning® ActiFi® 2-fiber/2-copper conductor composite cablePower Consumption70 WIngress ProtectionIngress protection rating: IP30Performance4CC; up to 64 active usersPeak Tx Rate1.8 Gbps DL, 60 Mbps UL (DL:UL slot ratio of 4:1) @ 64QAM with 4CC DL, 1CC ULLicensed Tx PowerEquivalent isotropically radiated power (EIRP): 43 dBmFronthaul NetworkDeployable over Corning® ActiFi® 2-fiber/2-copper conductor composite cableEthernet InterfaceSFP+ supports 10 GbE (Gigabit Ethernet)LEDs1 tricolor (RGB) LED to indicate power and status, 2 SFP LEDs to indicate Link/Activity statusSynchronizationIEEE 1588v2-based (PTP) synchronization with an external PTP grandmaster clockMountingWall or Ceiling, brackets includedBrackets support four wall-mount tilting options: 0°, 15°, 30°, and 45° tiltCooling MethodPassive convection cooling

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 107.ComplianceThe SCRN-530 complies with the standards listed in Table3.SecuritySecure boot and secure key storage using Trusted Platform Module (TPM) functionsIPsec tunneling to NR CU (Centralized Unit)X.509 certificate-based authenticationEnvironmental RequirementsOperating temperature range: 0 to 45°C (32° to 113°F)Non-operating temperature range: -40° to +70°C (-40° to 158°F)Relative humidity: Operating and storage: 5% to 90% RH non-condensingMTBF1,363,791 hours at +40°C (104°F)Table 3 Radio Node Compliance SafetySafety: UL-62368-1 2nd EditionFCC Compliant: Part 15 (Class A), Part 30 FCC 47 CFR 1.1307(b)MPE: FCC 47 CFR 1.1310Table 2 SCRN-530 Specifications (continued)

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 118.Mounting the SCRN-530The SCRN-530 can be installed on walls and below ceilings with the factory-provided brackets. When mounting a radio node on a wall, position the cooling fins vertically. The factory-provided wall-mount bracket can tilt the radio node down at the following angles: 0°, 15°, 30° and 45°. Figure5 shows the SCRN-530 downtilt options.Figure 5Mounting Bracket Downtilt OptionsNOTE:Always consult and follow local codes for mounting and wiring Corning equipment.When possible, locate downward-radiating radio node units at least 0.5 meters (20 inches) from external walls. This distance maximizes indoor coverage and minimizes RF leakage outside the building. When mounting near a wall or other obstruction, orient the mounting bracket so that the top of the radio node faces towards the coverage area and faces away from the wall. 8.1Installing the SCRN-530 on a CeilingAs shown in Figure3, the SCRN-530 comes with the ceiling-mount bracket attached. This bracket is held to the radio node mounting side with four shoulder screws and a captive securing screw, and is non-tilting. The shoulder screws should not need to be adjusted but if they do, loosen them slightly to be able to slide the ceiling-mount bracket on and off of the radio node when the captive securing screw has been loosened. Figure6 shows the captive securing screw and four security screw locations.NOTE:The security screws should not need to be adjusted but if they do, loosen them slightly to be able to slide the ceiling-mount bracket on and off.
0° 15° 30° 45°

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 12Figure 6Ceiling-Mount Bracket Screw LocationsStep 1Loosen the captive securing screw on the ceiling-mount bracket.Step 2Slide the ceiling-mount bracket toward the captive securing screw to remove it from the radio node base.NOTE:The shoulder screws should not need to be adjusted but if they do, loosen them slightly to be able to slide the ceiling-mount bracket on and off.Step 3Secure the ceiling tethering system. Make sure that it can support the weight of the radio node and the ceiling-mount bracket.NOTE:Corning recommends that you use a customer-supplied projector mount when hanging the radio node from a dropped T-bar ceiling.Step 4Secure the ceiling-mount bracket to ceiling tethering system. Step 5Slide the radio node back onto the bracket and gently tighten the securing screw.
Shoulder
Screws (4)
Captive
Securing
Screw

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 13Figure7 shows a radio node and the ceiling-mount bracket as the assembly can be mounted to a ceiling tethering system. Figure 7Radio Node with Ceiling-Mount Bracket8.2Installing the SCRN-530 on a WallThe SCRN-530 comes with the ceiling-mount bracket attached, and has the multi-angle wall-mount bracket loose in the box. Figure8 shows the radio node wall-mount bracket.Figure 8Radio Node Wall-Mount BracketWhen using the multi-angle wall-mount bracket, it is not necessary to remove the ceiling-mount bracket from the radio node; the wall-mount bracket attaches to the

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 14wall, and then it attaches to the ceiling-mount bracket-and-radio node assembly. Figure9 shows how the radio node wall-mount bracket attaches to the ceiling-mount bracket.Figure 9Wall-Mount Bracket Attached to the Ceiling-Mount BracketStep 1Using a spirit level, use the wall-mount bracket as a template to mark securing hole locations.Step 2If required, install sheet rock plugs.Step 3Attach the wall-mount bracket to the wall. Figure 8 shows the radio node wall-mount bracket.Step 4Seat the ceiling-mount bracket on wall-mount bracket:-First, attach the ceiling mount bracket to the radio node, than slide this subassembly into the wall bracket.-Then, set the radio node to the required tilt, and tighten the wall-mount bracket captive securing screw to lock the radio node tilt angle.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 15NOTE:Put pressure on the radio node when tightening the captive securing screw.Figure10 shows how to attach the wall-mount bracket to the ceiling-mount bracket.Figure 10Attaching the SCRN-530 with Ceiling-Mount Bracket to the Wall-Mount BracketStep 5Make sure that both of the captive securing screws are tightened.9.Cabling GuidelinesIncorrectly cabling the SCRN-530 can result in crushed cables and loss of communications to the radio node. Follow these guidelines when cabling the SCRN-530:•Make sure that the cabling is properly routed and dressed. •When mounting the radio node vertically, orient the bracket so that the bracket keyholes have the wide side up as shown in Figure3.•Make sure that the radio node is fully secured to the mounting brackets so that it locks into place. A correctly-installed cable should at no time during installation impede inserting the radio node into the mounting brackets.
12

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 1610.Completing the InstallationStep 1Make sure that the captive securing screws are tightened. The radio node is now anchored.Step 2When it receives power, the radio node boots up and attempts to connect to the centralized unit.11.Detaching the SCRN-530 from the Mounting BracketsStep 1Loosen the captive securing screw on the left side of wall mount bracket.Step 2Pull the plunger pin on the right side of the wall mount bracket and by pulling up take out the radio node from the wall mount bracket.Step 3Detach the cables from the cable brackets and cable connectors. Step 4Loosen the captive securing screw and slide out the bracket from the radio node.12.SCRN-530 LED Boot SequenceThe radio node state machine is sequential and progresses in the following order: State 0 -> State 1 -> State 2 -> State 3 -> State 4 -> State 5 -> State 6A normal boot sequence transitions through all these states sequentially and the LED state transitions accordingly. If the radio node fails to transition to the next state, the system restarts the boot sequence, starting with State 0. You can determine the progress during the booting stages by observing the LED color transitions. When the boot sequence completes, all devices are reachable.On failure, the LED state display the state that encountered the failure. Table4 shows the SCRN-530 boot sequence and corresponding LED behavior.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 17Table 4 SCRN-530 LED Boot SequenceStateLED ColorDescriptionPossible Failures and Actions0. Power On/ResetFlashing GreenThis is the initial state on startup. The radio node bootup is controlled by firmware in this state.This state should be very short lived and should transition to the next state immediately.1. Software InitializationFlashing GreenThe firmware has loaded and transferred control to the bootloader.Additional hardware initialization and validation are performed during this state. This state concludes with a lamp test, cycling through all LED colors.This state should be very short lived and should transition to the next state immediately.A radio node should not stay in this state indefinitely. Note: Flashing Green is also used to indicate a radio node that has been administratively disabled. This can be determined from the CLI.2. DHCPSolid RedThe radio node starts by sending out a DHCP Request. The radio node moves to the next state (State 3) upon receiving a DHCP response and an IP Address.No DHCP Response, IP Address not allocated.Check cabling, DHCP Server configuration.3. JoinSolid BlueThe radio node has an IP Address and sends a UDP Join request to the Serving centralized unit. The radio node moves to the next state (State 4) upon getting a JOIN GRANT from the centralized unit.No IP reachability to the centralized unit.Check IP network between radio node and centralized unit for routing issues.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 1813.SCRN-530 LED ManagementThe LED display is active by default, but can be deactivated in light-sensitive environments as needed. Even when the display is disabled, the LED will be lighted during the following conditions: •while the radio node is booting•if the radio node or cell is in fault stateTable5 lists the default LED behavior of the radio node.4. TFTPFlashing BlueThe radio node proceeds next to download the operating system image from the centralized unit. The radio node moves to the next state (State 5) after the image has been downloaded.Failure to download TFTP image. Check firewall between radio node and centralized unit.5. Operating System BootingSolid Green for a few seconds, off for about 30 seconds, then Solid GreenThe radio node loads the operating system and starts the default platform applications. The radio node moves to the next state (State 6) when it establishes connectivity with the centralized unit.Failure to start the operating system. This normally points to a software/build issue. Please contact Corning support.6. RunningSolid GreenThe operating system is running. The radio node continues the startup sequence, but is now controlled by the centralized unit.The operating system is up and running on the radio node. Any subsequent state transitions can now be tracked from events and logs on the centralized unit.Table 4 SCRN-530 LED Boot Sequence (continued)StateLED ColorDescriptionPossible Failures and Actions

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 1914.Disabling the LED DisplayStep 1From the CLI Configuration Mode, issue the set System RadioNode LED
DefaultMode Dark command to disable the LED display:%set System RadioNode LED DefaultMode Dark
Step 2Issue the show System RadioNode LED command to verify the configuration:%show System RadioNode LED
DefaultMode Dark;
15.Re-Enabling the LED DisplayStep 1From the CLI Configuration Mode, issue the set System RadioNode LED
DefaultMode Standard command to re-enable the LED display:%set System RadioNode LED DefaultMode Standard
Step 2Issue the show System RadioNode LED command to verify the configuration:%show System RadioNode LED
DefaultMode Standard; Table 5 SCRN-530 LED BehaviorLEDStatusFlash RateGreen: slow flashingThe radio node or radio is administratively disabledApproximately ½ second on, 1½ sec. offGreen: fast flashingSyncingApproximately 1.4 second on/off cycleGreen: solidOperationalRed: solidFaultBlue: fast flashingLocate radio node enabled (Note)Approximately 1 second on/off cycleOffPowered off or LED disabledNote: Refer to the Corning SCOS Administrator Guide for information about the locate radio node feature.

SCRN-530 Hardware Installation Guide | DOC-SCRN-530-HIG | 21 July, 2021 | Page 2016.SFP+ LED IndicationsThe enhanced small form-factor pluggable has a green Link Status Indicator LED, and an unused amber LED. The Link Status Indicator LED has the following operational modes:•OffNo Link (disconnected)•Solid Green10 Gbps link has been established17.Corning Documentation SetThe Corning documentation can be downloaded from the customer support portal (the “Corning One Community”) at https://onesupport.corning.com. This site requires a login which is available to individuals who have attended Corning Small Cell training in the past two years. Email on[email protected] to request a login if you meet these criteria.Corning Optical Communications LLC • 4200 Corning Place, Charlotte, NC 28216 USA800-743-2675 • FAX: [phone] • International: [phone] • www.corning.com/opcommCorning Optical Communications reserves the right to improve, enhance, and modify the features and specifications of Corning Optical Communications products without prior notification. A complete listing of the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are the properties of their respective owners. Corning Optical Communications is ISO 9001 certified. © 2021 Corning Optical Communications. All rights reserved.