Corning Eclipse interbay storage unit User manual

p/n 003-914, Issue 1

STANDARD RECOMMENDED PROCEDURE 003-914 | ISSUE 1 | MARCH 2012 | PAGE 1 OF 3

Eclipse®Interbay Storage

Unit

1. COMPONENTS

1.1. Major Components

1.2. Kit Contents:

• Rearmountingbrackets(2)

• 12-24screws(16)

• Galvanizedhexbolt(1)

• Galvanizedhexnut(1)

• 10-32nylonhexnut(1)

• 1/4lockwasher(1)

• #10atwasher(12)

2. TOOLS AND EQUIPMENT

Inadditiontothenormalsupplyoftools,a9/16wrench

willbenecessary.

3. PLANNING

Beforeyoubeginyourinstallation,makesureyou

understandhowtheunitistobeinstalled,wheretheunit

willbeplaced,andhowthejumperswillberouted.

4. INSTALLATION

4.1. Foot Cap Installation

Theunitcomeswithallroutinghubsandtroughsalready

assembled.Theonlyassemblyrequiredisattachingthe

unittotheframe.

Step 1: ThefootextensionthatcomeswiththeIBD

istobeinstalledrst.Todoso,removethe

twoscrewsonthefrontoftheframefootcap

toremovethecover.

Step 2: RemovethefootcapcoverfortheIBDby

removingthescrewsinthefrontandthe

back.

TPA-4096

Routing Hubs

Feed-through

Ports

TPA-4098

STANDARD RECOMMENDED PROCEDURE 003-914 | ISSUE 1 | MARCH 2012 | PAGE 2 OF 3

Step 3: Usethe3/8hardware(galvanizedhexnutandhexbolt)toattachthefootcapstogether.

Step 4: Reattachcoverstobothfootcaps.

5. STORAGE UNIT INSTALLATION

Step 1: MounttheIBDdirectlytothefrontangeoftheequipmentrackinthelocationsshown.

Attachthetwotogetherusingthe12-24screwsprovided.

Step 2: Toincreasethestabilityoftheunit,connectthebackoftheIBDtothebackangeofthe

frameusingtherearmountingbrackets.Use12-24screwstoattachthebracketsinthe

locationsshown.

NOTE: Ifyouarerunningberdownthesideoftheframeinthisarea,attachtherearbracketsafterber

routingiscomplete.

Step 3: IfusingtheIBDbetweentwoframes,mounttheunitonbothsidesinthesamemanner

describedinsteps1and2.

TPA-4097

TPA-4099

Front Rear

STANDARD RECOMMENDED PROCEDURE 003-914 | ISSUE 1 | MARCH 2012 | PAGE 3 OF 3





CorningCableSystemsreservestherighttoimprove,enhance,andmodifythefeaturesandspecicationsofCorningCableSystems’productswithoutpriornotication.

EclipseisaregisteredtrademarkofCorningCableSystemsBrands,Inc.Allothertrademarksarethepropertiesoftheirrespectiveowners.CorningCableSystemsisISO

9001certied.

©2012CorningCableSystems.Allrightsreserved.PublishedinMexico.

 

ThereareanumberofwaystousetheIBD:

Storeberslackbywindingexcessberaroundthehubs.

Jumper Management: UsetheIBDtoroutejumperstodifferentlocationswithintheframe.

Usethejumpertroughstorouteberfromoneequipmentracktoanother.

 SPECIFICATIONS

IBD Dimensions

Height: 84 inches

Width: 5 inches

Depth: 15.3 inches