Coros SafeSound User manual

SafeSound
Quick Start Guide

English- 01
COROS SafeSound-Road
Smart Cycling Helmet
Strap
Tri-glide splitters
Buckle
O-Ring
Ear Opening Sound System
Expanded polystyrene
Padding
Polycarbonate shell
Wind Resistant
Microphone

English- 0302- English
List of Contents
Smart Helmet, Smart Remote and Mount, Micro-USB Charging
Cable, Emergency Identification Card, COROS™ Helmet Bag,
Reflective Decal
COROS SafeSound-Urban
Smart Cycling Helmet
Strap
Tri-glide splitters
Buckle
O-Ring
Ear Opening Sound System
Expanded polystyrene
Padding
Polycarbonate shell
Wind Resistant
Microphone
COROS SafeSound-Mountain
Smart Cycling Helmet
Strap
Tri-glide splitters
Buckle
O-Ring Ear Opening Sound System
Expanded polystyrene
Padding
Polycarbonate shell
Wind Resistant
Microphone

How to Wear Your Helmet
WARNING: Please do not wear an improperly sized helmet,
even after adjusting the fastening system.
Place the helmet on your head as shown in Fig. 1. Then, slide
the tri-glide splitters just below your earlobes. Next, adjust the
strap to provide even tension between your neck and head.
Finally, adjust the knob on the helmet for proper fit.
Fig.1 shows the correct way to wear the helmet. Always wear
the helmet with the strap and buckle fastened. The strap
should be pulled tight and positioned back against the throat.
The leading edge of the helmet should land just above the
eyebrows.
Fig. 1. Correct Fig. 2. Incorrect
•
Fig. 2 illustrates the incorrect position for the helmet. Failure
to wear the helmet properly may cause discomfort to the rider
or even cause the helmet to shift or fall off during an accident.
•
04- English English- 05
Ear Opening Sound System. EOSS is a groundbreaking
technology that delivers a unique combination of sharp
audio and full environmental awareness. No distractions, no
noise, and no vibrations. Just crystal-clear audio for music
and calls, while leaving the ears completely open for
environmental awareness.
Smart Communication. Safely receive phone calls while
you ride with the included Smart Remote and
windresistant microphone.
Voice Navigation. Record your ride data when you
enter use the COROS App to track your ride. You can
also use 3rd party navigation apps for voice navigation
during your ride.
Wireless Music Player. Stream or play your favorite
audio from your phone by connecting the helmet via
Bluetooth.
Smart Connection. Easily control your music, phone
calls, ride data, voice navigation and LED safety lights
all via the ANT+ enabled smart remote.
LED Tail Light. Remain seen during the day or at night.
You have the option of on, off, or auto mode to control
the lighting while you ride.
SOS Emergency Alert. Upon impact, SafeSound will
automatically notify your list of emergency contacts
with an exact location map pin, while flashing SOS in
Morse code.

How to Wear Your Helmet (cont.)
Fig. 3. Fig. 4.
The tri-glide splitter as shown in Fig. 3 is a key component for
positioning the helmet and EOSS. Adjust the tri-glide splitters
on each side of the helmet so that the left strap and right
strap come together just under the earlobes.
•
Fig. 4 shows how the chin strap also plays an important role
in positioning the helmet. Adjust the length of the strap and
the location of the buckle to create a comfortable, yet firm
tightness around your chin and head.
•
Tri-glide
splitters O-Ring
Control knob
Fig. 6.
Fig. 5.
Fig. 6 shows how the helmet will
look from the front when adjusted
correctly.
•
SafeSound is equipped with an adjustable fit system which
helps stabilize the helmet when worn in the correct position
while riding. Fig. 5 shows where to locate the adjustable
knob. Turn the knob clockwise to tighten and
counterclockwise to loosen.
•
06- English English- 07

COROS GO
Charging
Please fully charge your SafeSound helmet before your ride. To
charge, flip open the micro-USB protective cover, located at the
back of helmet. Next, plug-in the included charging cable, as
shown in Fig. 7.
Turning On/Off
To turn the helmet ON, hold the power button for 2-seconds until
you hear EOSS say, “power on” . To turn the helmet OFF, hold
the power button for 2-seconds until the LED indicator light
turns off.
How to Operate the Smart Functions
Fig. 7.
Pairing your SafeSound Helmet
1. See www.coros.com for compatible iOS and Android devices.
Fig. 8.
Option1: Search and Download >
Option 2:
Scan Quick Response Code >
iOS / Android
In the App or Google Play Store,
search for the “COROS App” .
and download it directly to your
phone.
To pair your helmet with your phone, first power on the
helmet. On your phone, turn Bluetooth to on and enter the
pairing interface to select "COROS SafeSound" for pairing.
(See Fig. 8)
2.
Download the COROS App. (see Fig. 9).
3.
Fig. 9.
English- 0908- English
COROS SafeSound

Connecting the Smart Remote
To connect your SafeSound helmet, launch the
COROS App. After a few seconds, the app will automatically
detect your helmet and establish connection. (see Fig. 10)
4.
Pairing: Using the COROS App, navigate into the SafeSound
menu from the Device Page. Then press on the "Remote"
option to enter the pairing interface (see Fig. 11). Press the
"Pair a new Remote" button
(see Fig. 12) and then press and hold any key on the Smart
Remote until the “Successfully Paired” message appears.
1.
Fig. 14.
Image 1. Image 2. Image 3.
Mounting your Smart Remote: Included with the Smart
Remote are 2-rubber rings and the remote holder. Find a spot
on your handlebar to mount the holder, near your right or left
hand (Fig. 14, Image 1). Position the first rubber ring at one
corner of the holder and stretch the ring underneath to latch
on the opposite corner as shown in Image 2. Attach the
second rubber ring to the other two corners. Image 3 shows
how the the holder looks when installed correctly, with the
Smart Remote placed into position.
Note: The orientation of the Smart Remote is flexible based
upon the rider’ s preference.
2.
English- 1110- English
Fig. 10. Fig. 11. Fig. 12.
Add New Device
SafeSound
ID:78ED2P
Start Cycling Emergency Contact
SafeSound
Firmware Update V1.0
Taillights
Voice Feedback
User Guide
Remote
SafeSound
ID:78ED2P
选择遥控器
Click: Volume up
Hold for 2s: Taillight On/Off/Auto
Click: Volume down
Hold for 2s: Real-time ride data prompt
Click: Play or pause music/pick up or hang up call
Hold for 2s: refuse the call
Click: Previous track
Click: Next track
Hold for 2s: Walkie-talkie after one beep
SafeSound
ID: F4507
Pair a new Remote

Smart Remote Functions
Function Status Confirmation
Play / Pause Music
Pick Up / Hang Up Call
1
2
3
4
5
Refuse Call
Volume Down
Real-Time Ride Data
Previous Track
Next Track
Walkie-Talkie
Volume Up
Adjust LED Tail Light Mode
Press Button 1
Press Button 1
Hold Button 1
Press button 2
Hold Button 2
Press button 3
Press Button 4
Hold Button 4
Press Button 5
Hold Button 5
-
-
-
-
Two beeps
-
-
One beep
-
Voice notification
1
3
5
4
2
LED
Safety LED Tail Light
Red Flashing light
Red
Charging -
Flashing light
Fully charged -
Solid light
Red Light indicates real-time
battery level
Red
Blue
Red
Solid light, then off
Blue Solid light, then off
Flashing light
real time battery
level, solid red in 1S,
then red light off；
Light Color FrequencyFunction
Safety Light
Charging
Power on
Power Off
Bluetooth Connected
English- 1312- English
Power
Buttont
Bluetooth Disconnected
Battery Level

COROS™ warrants the original purchaser of this product that the product
is free of defects in material and workmanship for a period of one year
(US, CA & AU) or two years (EU) from the original date of purchase. This
warranty does not apply to defects of physical damage resulting from
neglect, abuse, improper repair, usage, fit, alterations, or any use
unintended by the manufacturer. COROS™ does not warrant any helmet
damaged due to heat or contact with solvents. This warranty is in lieu of
all other agreements and warranties, general or special, express or
implied and no representative or person is authorized to assume
liabilityon behalf of COROS™ in connection with the sale or use of this
product. If your COROS™ helmet is found to be defective in materials or
workmanship within one year (US, CA & AU) or two years (EU) from the
date of purchase, COROS™ or the country distributor will at its sole option
either repair or replace the helmet free of charge.
1. Unable to power on helmet
Try charging the helmet for 2 to 3 hours.
2. After power on, the helmet automatically powers off after a
shortperiod of use.
Perform a “hard reset” by pressing the power button for a
period of 8 seconds.
3. No response for remote pair or operation.
After several failed attempts to pair the helmet, please contact
COROS support at www.coros.com or [email protected]
For complete troubleshooting information, please visit
www.coros.com
Troubleshooting of Electronic
Functions
Limited Warranty
Specifications
English- 1514- English
Charge Interface Micro-USB
Electrical Input DC 5V / 1A
Charging Time 3-hours
Standby Time Up to 180-days
Bluetooth Profile
Speaker Output
Speaker Volume
Mic Sensitivity
BLE, A2DP, HFP, SPP, AVRCP, HSP
0.5W*2
85±3dB
﹣42± 3dB
Bluetooth Operational
Distance Up to 33 feet / 10m
Premium silicon material
Safety cycling light and sensor. Light activated
based on surrounding lighting conditions. 3 RGB
LED per side.
Proprietary open ear premium speakers
Main PCBA
500mAh Lithium battery
Adjustable fit system with control knob
Hot-press lining + EVA padding
Adjustable strap helps properly position the helmet
for safety and audio operation.
Microphone
LED
Ear Opening Sound
System
PCBA
Battery
Adjustable System
Padding
Helmet/Chin Strap
Microphonet Up to 8+ hours play / talk

English- 1716- English
C.P.S.C.16 CFR Part 1203
United States Federal Safety Standard for Bicycle Helmets
(Consumer Product Safety Commission)
CE, EN1078 (Europe Safety Standard)
FCC ID: 2AEHH- SAFESOUND
FCC Part 15B,Part 15C
RED Directive 2014/53/EU
AS/NZS 2063:2008 (Australia/New Zealand Bicycle Helmet
Safety Standard)
Safety Certifications
Instructions for use and care
No helmet can protect the wearer against all possible
impacts.
The helmet is designed to be retained by a strap
under the lower jaw.
To be effective, a helmet must fit and be worn
correctly. To check for correct fit, place helmet on
head and make any adjustments indicated. Securely
fasten retention system. Grasp the helmet and try to
rotate it to the front and rear. A correctly fitted helmet
should be comfortable and should not move forward
to obscure vision or rearward to expose the forehead.
No attachments should be made to the helmet except
those recommended by the helmet manufacturer.
The helmet is designed to absorb shock by partial
destruction of the shell and liner. This damage may
not be visible. Therefore, if subjected to a severe
blow, the helmet should be destroyed and replaced
even if it appears undamaged.
The helmet may be damaged and rendered
ineffective by petroleum and petroleum products,
cleaning agents, paints, adhesives and the like,
without the damage being visible to the user.
A helmet has a limited lifespan in use and should be
replaced when it shows obvious signs of wear.
This helmet should not be used by children while
climbing or doing other activities where there is a risk
of hanging or strangulation if the child gets trapped
whilst wearing the helmet.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.

COROS™ Wearables Inc.
No. 1844 GRAHAM LANE, SANTA CLARA, CA 95050, USA
[email protected]
For updated product and mobile app information, please visit
www.coros.com
Contact
FCC Statement
Maintenance
1. Keep the helmet far away from high temperatures over
65.5C or 149.9F, as it may cause damage to the helmet. Do
not keep the helmet inside your car for long periods of time or
store it in tightly sealed containers or bags where high heat
can accumulate and cause damage to the helmet. Do not use
the helmet if it has been deformed by heat.
2. Make sure the helmet is clean and dry after each use. Store
the helmet in a dry and ventilated location.
Storage
Clean the helmet with mild soapy water. Avoid use of specific
solvents such as ammonia, bleach, paints, abrasives or
hydrocarbons which may damage the helmet and cause it to fail
to protect the head in the accident.
18- English English- 19
passed EN1078:2012+A1:2012 to show conformity to the EHSR
of Regulation (EU) 2016/425
EU Type examination conducted by SGS United Kingdom Ltd,
Weston-super-Mare, BS22 6WA, UK. Notified Body No: 0120
DOC internet address is www.coros.com
The helmet can only protect if it fits well and that the buyer should
try different sizes and choose the size which feels secure and
comfortable on the head;
This helmet is designed to protect impact caused by the collision
of the head with an obstacle while cycling or roller skating, it has
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.