Costway TS10037 User manual

Please give us a chance to make it right and do better !
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP !
Contact Us !
Do NOT return this item. US:[e-mail]
UK:[e-mail]
AU:[email protected]
Kids Wooden Boat Sandbox
TS10037
USER’S MANUAL
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
US office: Fontana UK office: Ipswich AU office: Truganina

Side Board x2
Parts and Hardware List
Side Board x2 SideBoard x2
￠6*25
Ax8
3.5*25
Cx8
3*14
Bx24
Rail x4 Side Board x2 Side Board x2
Bench x4 Disk x2 Side Board x 2 Flag x2 Backrest x2
Bench x1 Side Board x2 Side Board x1 Pole x2 Mat x1
Not actual size
3
1
4
2
5 6 7
8 9 10 11 12
13 14 15 16 17
Actual size
SCREW SCREW SCREW SCREW
3.5*30
Dx24
SCREW
3.5*35
Ex30
Side Board x2
Before You Start
Warning for Assembly
Assembled only by adults
Remove all Packaging, separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near the area in
which they will be placed in use, to avoid moving the product unnecessarily once
assembled.
Ensure a secure surface during installation, and place the product always on a flat,
steady and stable surface.
General Security Warning
Caution: The Product is not suitable for the children under 3 years
Danger: Keep all small parts and packaging materials for this product away from babies
and children, otherwise they may pose a choking hazard.
Danger: Lack of attachment may cause a risk of tipping.
WARNING:
CHOKING HAZARD-Small parts.
Not for children under 3 years.
0-3
Please read all instructions carefully and keep it for future reference.
02 03

4
3
3
4
2
2
1
1
01 02
Fasten side board 3 and side board 4 tightly, and pay attention to the
direction of the screw holes as shown in the figure.
Fasten side board 1 and side board 2 tightly, and pay attention to
the direction of the screw hole and the upward screw holes as
shown in the figure.
04 05

D
5
5
5
D
5
3.5*30
Dx8
3.5*30
Dx8
03 04
Stack Figure of step 2 on top of Figure of step 1, the upper side board
2 to the lower side board 4, the upper side board 1 to the lower side
board 3. Use 8 PCS D screws to fix rail 5 as shown in the figure.
Use 8 PCS D screws to fix the other side rail 5.
06 07

6
7
6
7
8
B
E
05 06
3.5*35
E x24
3*14
B x24
Stack side board 6 to side board 2, side board 7 to side board 1 with
the concave holes facing upwards. Use 24 PCS E screws to fit into the
holes and tighten.
Fix bench 8 on the four corners with 24 PCS B screws.
08 09

7
A
9
11
11
D
07 08
3.5*30
D x4
￠6*25
Ax4
Fix flag 11 on the both sides with 4 PCS A screws. Fix disk 9 on the one side with 4 PCS B screws.
10 11

9
D
9
10
09 10
3.5*30
D x4
Fix disk 9 on the other side with 4 PCS B screws. Fix side board 10 on the both sides.
12 13

A
12
12
E
13
14
14
11 12
3.5*35
E x6
￠6*25
Ax4
Fix backrest 12 to flag 11 tightly with 4 PCS A screws. Use 6 PCS E screws to fix bench 13 and side board 14 as shown.
14 15

15
16
16
C
17
13 14
3.5*25
C x8
Place the assembled components on mat 17 and lay out parts 15
evenly as shown.
Fix pole 16 on the both sides with 8 PCS C screws.
16 17