CountyLine CL-30P-DDF Manual

Please note the serial number of your fan, and write it on the back of this User’s Manual for future reference.
Model Numbers: CL-30P-DDF, CL-20F-DDF,
CL-24O-DDF, CL-30-DDF
User’s Manual and
Operating Instructions
950450280-12
This product meets and exceeds the requirements of OSHA 1910.212(a)(5), the standard which
regulates electric fan blade safety, and is certified under UL# E234000, established and made
effective April 10, 2003, and updated March 23, 2005, by Underwriters Laboratories, Inc.
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT: Read and understand all of the directions in this manual before assembling,
starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for
future reference.
For ventilating use only. Do not use to exhaust hazardous chemicals or use near
any flammable liquids or gases as sparks from motor may ignite fumes. Never use
the fan in spaces which contain products such as gasoline, solvents, paint thinners, dust particles,
volatile or airborne combustibles, or any unknown chemicals.
WARNING
Distributed by: TRACTOR SUPPLY COMPANY 200 POWELL PLACE
BRENTWOOD, TN 37027
For customer support, call: 1-866-641-4540

Safety Information.............................................. 2
20” Floor Fan...................................................... 3
24” Barrel Fan.................................................. 4-5
30” Pedestal Fan............................................. 6-7
30” Drum Fan................................................ 8-10
Troubleshooting................................................ 11
Warranty........................................... Back Cover
Table of Contents
Safety Information
- Turn off, unplug unit, and wait for fan to stop
before moving, storing, and / or changing
operating locations.
- Operate only on 115 volt 60 Hz (cycle) current
with a minimum of a 15 amp circuit.
- Before operating always check fan for loose or
damaged parts. Inspect power cord for any
damage. Never use fan if any parts are
damaged or missing. Never use fan without
safety guards attached.
- When used with an extension cord, use only
cord of proper size (Amp rating), UL listed, and
with receptacle to accept three prong grounded
plug furnished on the fan’s power cord. Always
keep power cord and extension cords away
from heat, oil, and sharp edges. Inspect cords
periodically and replace if damaged.
- Disconnect fan from power source when not in
use, before servicing and when cleaning or
repairing.
- Repair of this appliance should be done by a
qualified electrician.
- In case of power failure, turn fan off at knob or
power chain to prevent unexpected restarting
and component damage.
- Keep children away from fan at all times.
IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY, SERVICE OR USE
OF THIS FAN. FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN
SERIOUS PERSONAL INJURY AND / OR PROPERTY DAMAGE.
This unit is designed for indoor
use only. Do not expose to
elements or allow to become wet.
WARNING
To guard against electric shock
while operating, do not allow fan
to come in contact with other grounded objects
such as pipes, radiators, etc.
WARNING
To Reduce The Risk Of Fire Or
Electric Shock, Do Not Use This
Fan With Any Solid- State Speed Control
Device.
WARNING
Risk of fire, electric shock, or
personal injury when performing
service or maintenance. Unplug or disconnect
the fan from the power supply before servicing.
WARNING
If safety guards have been removed to service or maintain this fan, reinstall or remount the safety
guards as previously installed.
To Reduce The Risk Of Electric
Shock And Injury To Persons, Do
Not Use In a Window.
WARNING
For General Ventilating Use Only.
Do Not Use To Exhaust
Hazardous Or Explosive Materials And Vapors.
WARNING
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
2www.TractorSupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User’s Manual
DO NOT MOVE FAN WHILE
OPERATING! MOVING FAN DURING
OPERATING CAN CAUSE BLADE DAMAGE.
WARNING

NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
HVF Air Circulator User’s Manual For customer support, call 1-866-641-4540 www.TractorSupply.com 3
Replacement Parts
Item # Description Part Number
1Logo Plate 95-043-0365
2Front Grille 95-032-0160
3, 4, 5 Fan Blade Assembly 95-003-0615
6Frame Washer 95-024-0250
7Frame-Support L 95-024-0265
8Main Circle Tube 95-024-0280
9Top Washer 95-024-0290
10 Rear Grille 95-032-0260
11 Motor 95-030-0525
12 Switch Holder 95-031-0310
13 Switch 95-031-0120
Item # Description Part Number
14 Switch Cover 95-031-0510
15 Cord Bushing 95-026-0165
16 Control Knob 95-027-0110
17 Front Foot 95-023-0220
18 Rear Foot 95-023-0230
19 Frame-Support R 95-024-0275
20 Swivel Spacer 95-050-0180
21 Lower Support Frame 95-024-0245
22 Power Cord 95-026-0240
23 Capacitor 95-004-0225
24 Wall Mount Kit 95-078-0100
If the Wall Mount Kit is applied, the
installer MUST be certain that the
support bracket is mounted to a minimum of a 2x4”
stud, and that it is able to support 50 pounds
continuously.
1. Remove 1 screw from each Frame Support L and R
(Items 7 and 19).
2. Slide Frame Support L and Frame Support R into
Support Frame (Item 21) and line up holes for screw.
3. Re-attach screw to Frame Support L and Frame
Support R.
20” FLOOR FAN
12345678910 11 12 13 14
15
16
23
22
17
18
19
20
21
Figure 1: Exploded View of CL-20F-DDF
24
Installation and Assembly (requires Phillips head screwdriver)
Exploded View
WARNING

1. Locate fan in safe, desired position on level ground,
and connect to approved power source.
Replacement Parts
Item # Description Part Number
1Front Grille 95-043-0415
2Fan Barrel 95-001-0400
3Power Knob 95-027-0130
4Power Knob Holder 95-031-0325
5Capacitor 95-004-0235
6Power Cord 95-026-0255
7Motor 95-030-0535
8Motor Mount Assembly 95-030-0555
9Motor Cooling Fan 95-030-0556
10 Fan Blade Assembly 95-003-0625
11 Rear Grille 95-032-0275
12 Front Leg 95-009-0600
13 Horizontal Adj. Knob 95-015-0150
14 Spacer 95-050-0200
15 Outer Ring Frame 95-024-0320
Item # Description Part Number
16 Vertical Adj. Knob 95-015-0150
17 Wall Mount 95-078-0200
18 Handle Pad 95-007-0100
19 Spacer 95-050-0200
20 Handle Arm 95-006-0300
21 Rear Leg 95-009-0610
22 Large Base Cap 95-024-0410
23 Large Base 95-024-0400
24 Foot Pad 95-023-0240
25 Wall Bracket - L 95-077-0100
26 Wall Bracket - R 95-077-0110
27 Small Base 95-024-0500
28 Small Base Cap 95-024-0500
29 Wheel 95-024-0510
30 Lower Mount 95-024-0325
Installation and Assembly - Floor
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
4www.TractorSupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User’s Manual
Exploded View
12
345
7
8
9
10 11
12 13 14
16
19
17
18
21
20
22
23
25
26
27
Figure 2: Exploded
View of CL-24O-DDF
28
24
29
30
15
6
24” BARREL FAN

24” BARREL FAN
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
HVF Air Circulator User’s Manual For customer support, call 1-866-641-4540 www.TractorSupply.com 5
If the Wall Mount Kit is applied, the
installer MUST be certain that the
Wall Mount is mounted to a minimum of a 2x4” stud,
and that it is able to support 50 pounds continuously.
1. Attach Wall Mount (item 17 on page 4) to wood stud as
shown below.
2. Slide Wall Bracket L and Wall Bracket R on Large Base
(item 23) onto Wall Mount.
WARNING
Installation and Assembly - Wall Mount (requires flat head screwdriver)
Wall
Wall
Wall Mount (item 17)
Handle Arm (item 20)
Wall Mount
(item 17)
Large Base
(item 23)
Figure 3: Wall Mount installation

Installation and Assembly
REQUIRED TOOLS:
Pliers
Knife
Phillips head screwdriver
Flat head screwdriver
10mm / adjustable wrench
6mm hex wrench (included)
PARTS INCLUDED IN BOX:
Rubber Base Ring
Base
Front Grille
Rear Grille
Motor Assembly
Fan Blade Assembly
Spring
Support Pole Assembly
1. Attach Rubber Base Ring (item 16 on page 7) to outer
edge of Base (item 15). Be sure ribbed side of Base
Ring is facing down.
2. Remove 5 screws from Flange on bottom of Lower
Support Pole (item 16).
3. Completely extend Upper Support Pole (item 21) from
Lower Support Pole and insert Spring into bottom of
Lower Support Pole.
4. Attach Support Pole Assembly to Base. Tighten
hardware using star parttern to insure a tight, uniform
fit.
5. Stand assembly on Base, and press down Upper
Support Pole and then tighten Height Adjustment Knob
(item 3).
6. Attach Motor Support Assembly to Motor Assembly
(see figure 5).
7. Place Motor Support into Upper Support Pole.
- Insert Pivot Bolt and tighten.
- Insert Tilt Adjustment Knob and tighten.
8. Remove 4 screws on motor, and attach the Rear Grille.
Tighten screws only after all 4 screws are reattached to
the motor.
9. Remove the screws on the Motor and attach the Rear
Grille onto groove in motor shaft, and replace screws
(See figure 4).
10. Loosen the set screw on the back of the Fan Blade
Assembly and slide onto the motor shaft.
11. Position set screw over flat groove on motor shaft and
tighten set screw using 6mm hex wrench (included). Be
sure set screw is on the groove, and the front of Fan
Blade Assembly is flush with front of shaft before
tightening.
12. Attach Front Grille by first aligning the top hooks of the
Front Grille onto the top of the Rear Grille edge. Work
your way around the grille, placing the Front Grille
hooks over the Rear Grille edge. If necessary, use a
flat head screwdriver to help pry the Front Grille hooks
over the Rear Grille edge. Continue until all hooks are
completely attached to the Rear Grille edge.
Do NOT slide fan blade screw
beyond the groove on the shaft!
This will cause the fan blade to not spin properly and
can cause damage to your fan! Be sure that fan shaft
is flush with front of fan blade assembly.
CAUTION
30” PEDESTAL FAN
Motor Assembly
Machine Screw
Pivot Bolt
Tilt
Adjustment
Knob
Motor Support
Assembly
Wing Nut
Nut
Upper Support Pole
Figure 4: Attaching Rear Grille to Motor
Rear Grille
Motor
Figure 5: Attaching Motor to Motor Support Assembly
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
6www.TractorSupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User’s Manual

30” PEDESTAL FAN
Item # Description Part Number
1Logo Plate 95-043-0360
2Front Grille 95-032-0180
3Height Adjustment Knob 95-015-0205
4, 5, 6 Fan Blade Assembly 95-003-0630
7Power Switch (Chain) 95-031-0140
8Motor Assembly 95-030-0545
9Rear Grille 95-032-0280
10 Height Adjust. Knob Nut 95-015-0215
11 Pipe Ring 95-017-0215
12 Pipe Support 95-017-0220
13 Lower Support Pole 95-017-0205
Item # Description Part Number
14 Latch Spring 95-060-0210
15 Upper Base 95-024-0225
16
Lower Base (Rubber
Base Ring) 95-024-0235
17 Motor Support 95-030-0560
18 Left Support 95-030-0570
19 Right Support 95-030-0575
20 Tilt Adjustment Knob 95-015-0210
21 Upper Support Pole 95-010-0305
22 Power Cord 95-026-0260
23 Capacitor 95-004-0240
Replacement Parts
Figure 6: Exploded View of
CL-30P-DDF
1
2
12
456
7
98
3
10
11
13
14
16
17
19
22
21
15 20
18
23
Exploded View
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
HVF Air Circulator User’s Manual For customer support, call 1-866-641-4540 www.TractorSupply.com 7

30” FLOOR FAN -OPTIONAL CEILING MOUNT
1
2
34
567
8
9
10
11
12
13 14 15
16 17
18
19
20
21
22 23
Exploded View
24
26
25
26
Replacement Parts
Item# Description Part Number
14 Wheel Axle 95-008-0260
15 Wheel Frame 95-008-0500
16 Upper Swivel Housing 95-050-0141
17 Frame Lower Swivel Latch 95-050-0150
18 Latch Spring 95-060-0155
19 Lower Swivel Housing 95-050-0161
20 Rear Guard 95-032-0240
21 Rear Swivel Bracket 95-050-0170
22 Capacitor 95-004-0200
23 Power Switch 95-025-0500
24 Rear Motor Cover 95-048-0100
25 Power Cord 95-026-0150
26 Guard Latch Assembly 95-033-0220
Item# Description Part Number
1Front Guard 95-032-0140
2 Front Swivel Bracket 95-050-0100
3 Fan Blade Assy 95-003-0505
4 Fan Holder 95-003-0150
5 Motor 95-030-0500
6 Frame Foot 95-023-0200
7 Cart Frame 95-009-0400
8 Swivel Cover 95-050-0106
9 Frame Swivel Bracket 95-050-0111
10 Frame Upper Swivel Latch 95-050-0120
11 Swivel Latch Pin 95-050-0131
12 Frame Cap 95-011-0300
13 Wheel 95-008-0160
Figure 7: Exploded View of CL-30-DDF
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
8www.TractorSupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User’s Manual

30” FLOOR FAN -OPTIONAL CEILING MOUNT
Floor Installation
Simply locate fan in safe, desired position on level
ground, and connect to approved power source.
NOTE: This fan uses a folding wheel design. For quick
assembly, simply swing the wheels out and snap to
lock in place.
Ceiling Mount Installation
The installer MUST be certain that the
ceiling that the mounting bracket is
mounted to is able to support 100 pounds continuously.
MOUNTING BRACKET INSTALLATION:
1. Remove Wheel Frame (item 15 on page 8).
2. Attach Cart Frame to Ceiling beam using U-bolts (item
5 on page 10).
3. Assemble and attach Ceiling Mount Assembly as
shown in figure 10 on page 10.
SAFETY CABLE INSTALLATION:
1. After the fan is securely mounted, feed the safety cable
between one of the swivel brackets as shown in figure
8.
2. Pull safety cable through and secure cable with safety
cable U-bolt as shown in figure 9.
3. Take other end of cable and wrap around beam
4. Secure cable loop as shown in step 2. Be sure there is
approximately 2 inches of slack in the safety cable
once both ends are secured.
5. Repeat on other side of fan so there are two safety
cables.
Figure 8: Safety Cable Installation Figure 9: Safety Cable Installation- Close Up
WARNING
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
HVF Air Circulator User’s Manual For customer support, call 1-866-641-4540 www.TractorSupply.com 9

30” FLOOR FAN -OPTIONAL CEILING MOUNT
Item# Description Part Number
1Safety Cable Assy 95-060-0100
2Nut for Ceiling Swivel Pin 95-060-0180
3Nut 95-060-0125
4Upper Ceiling Bracket 95-060-0110
5U-Bolt 95-060-0120
1
3
5
6
7
8
9
Ceiling Kit Replacement Parts
Ceiling Kit Exploded View
2
4
Item# Description Part Number
6Top Washer 95-060-0120
7Lower Ceiling Bracket 95-060-0160
8Tapping Screw 5-15mm 95-060-0195
9Ceiling Swivel Pin 95-060-0170
Figure 10: Exploded View of CL-30-DDF (ceiling mount kit)
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
10 www.TractorSupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User’s Manual

Troubleshooting Guide
Problem Possible Cause Corrective Action
Fan does not operate 1. No power Inspect power cord for damage. Be sure unit is
plugged in and turned on.
2. Bad motor Replace motor
Reduced Air Flow 1. Obstruction Turn off and unplug fan. Remove guard and make sure
nothing is obstructing the fan blades.
2. Bad switch or capacitor Replace switch or capacitor (Note: To prolong life of
fan, operate fan first in 1(LOW) for 5-10 seconds before
switching to higher speed.
Humming sound but no
operation
1. Bad capacitor Replace capacitor
Excess Noise (vibration,
squealing)
1. Fan is not on level ground Turn off fan, and move unit to smooth level surface.
2. Guard is not secure Check guard screws to be sure all are tight.
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
HVF Air Circulator User’s Manual For customer support, call 1-866-641-4540 www.TractorSupply.com 11

ALWAYS BE SURE TO SPECIFY MODEL NUMBER AND SERIAL NUMBER WHEN MAKING ANY CLAIM
WITH THE MANUFACTURER. FOR YOUR CONVENIENCE USE THE SPACE PROVIDED BELOW TO LIST
THIS INFORMATION:
Model #: ____________________ Serial #: ______________________
Date of Purchase: _________________
NEVER LEAVE A FAN
UNATTENDED WHILE
OPERATING OR WHILE
CONNECTED TO A POWER
SOURCE
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original retail purchaser
only, to be free from defects in material and workmanship for a period of
one (1) year from the date of initial purchase. This product must be
properly installed, maintained and operated in accordance with the
instructions provided.
The manufacturer requires reasonable proof of your date of purchase
from an authorized retailer or distributor. Therefore, you should keep your
sales slip, invoice, or cancelled check from the original purchase. This
Limited Warranty shall be limited to the repair or replacement of parts,
which prove defective under normal use and service within the warranty
period, and which the manufacturer shall determine at its reasonable
discretion.
This warranty does not apply to products purchased for rental use.
This Limited Warranty does not cover any failures or operating difficulties
due to normal wear and tear, accident, abuse, misuse, alteration,
misapplication, improper installation or improper maintenance and service
by you or any third party. Failure to perform normal and routine
maintenance on the fan, shipping damage, damage related to insects,
birds, or animals of any kind, and damage due to weather conditions are
also not covered. In addition, the Limited Warranty does not cover
damage to the finish, such as scratches, dents, discoloration, rust or
other weather damage, after purchase.
All transportation costs for the return of the damaged product or parts will
be the responsibility of the purchaser. Upon receipt of damaged item, the
manufacturer will examine the item and determine if defective. the
manufacturer will repair or replace and return the item, freight pre-paid.
If the manufacturer finds the item to be in normal operating condition, or
not defective, the item will be returned freight collect.
This Limited Warranty is in lieu of all other express warranties. The
manufacturer disclaims all warranties for products that are purchased
from sellers other than authorized retailers or distributors.
AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED WARRANTY
EXPIRES, THE MANUFACTURER DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR APPLICATION. FURTHER, THE MANUFACTURER
SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY
THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The manufacturer
assumes no responsibility for any defects caused by third parties. This
Limited Warranty gives the purchaser specific legal rights; a purchaser
may have other rights depending upon where he or she lives. Some
states do not allow the exclusion or limitation of special, incidental or
consequential damages, or limitations on how long a warranty lasts, so
the above exclusion and limitations may not apply to you.
The manufacturer does not authorize any person or company to assume
for it any other obligation or liability in connection with the sale,
installation, use, removal, return, or replacement of its equipment, and
no such representations are binding on The manufacturer.
Always be sure to specify model number and serial number when making
any claim with the manufacturer.
HVF Air Circulator User’s Manual For customer support, call 1-866-641-4540 www.TractorSupply.com