Craftex CX508 User manual

MODEL CX508
14" OSCILLATING
SPINDLE SANDER
USER MANUAL
Version 1.0

2
TABLE OF CONTENTS
General Safety Instructions..................................................................................... 3
Specific Safety Instructions..................................................................................... 4
CX508 Features...................................................................................................... 5
Physical Features ................................................................................................... 6
Unpacking............................................................................................................... 7
Workbench Load..................................................................................................... 7
Clean Up................................................................................................................. 7
Proper Grounding ................................................................................................... 8
Mounting On A Workbench..................................................................................... 9
Switch Disabling Key .............................................................................................. 9
Sanding Drum/Sleeve Installation...........................................................................10
Test Run.................................................................................................................10
Sanding...................................................................................................................11
Maintenance ...........................................................................................................11
Cleaning..................................................................................................................11
Parts Diagram.........................................................................................................12
Parts List.................................................................................................................13
Warranty.................................................................................................................14

3
GENERAL SAFETY INSTRUCTIONS
FOR MACHINES
Extreme caution should be used when operating all power tools. Know your power
tool, be familiar with its operation, read through the user manual and practice safe
usage procedures at all times.
ALWAYS read and understand the
user manual before operating the
machine.
CONNECT your machine ONLY to the
matched and specific power source.
ALWAYS wear safety glasses
respirators, hearing protection and
safety shoes, when operating your
machine.
DO NOT wear loose clothing or
jewelry when operating your machine.
A SAFE ENVIRONMENT is
important. Keep the area free of dust,
dirt and other debris in the immediate
vicinity of your machine.
BE ALERT! DO NOT use prescription
or other drugs that may affect your
ability or judgment to safely use your
machine.
DISCONNECT the power source when
changing drill bits, hollow chisels,
router bits, shaper heads, blades,
knives or making other adjustments or
repairs.
NEVER leave a tool unattended while it
is in operation.
NEVER reach over the table when the
tool is in operation.
ALWAYS keep blades, knives and bits
sharpened and properly aligned.
ALL OPERATIONS MUST BE
performed with the guards in place to
ensure safety.
ALWAYS use push sticks and feather
boards to safely feed your work through
the machine and clamp the work-piece
(when necessary) to prevent the work-
piece from any unexpected movement.
ALWAYS make sure that any tools used
for adjustments are removed before
operating the machine.
ALWAYS keep the bystanders safely
away while the machine is in operation.
NEVER attempt to remove jammed
cutoff pieces until the saw blade has
come to a full stop.

4
Always inspect the stock for any nails,
staples, knots or any other
imperfections before sanding.
For the protection of your eyes, always
wear safety glasses, goggles or face
shield while operating the sander.
Never touch the moving sanding disc.
Keep your hands and fingers away
from the moving sanding disc. If the
work-piece is small or difficult to hold,
use work-piece holding fixture.
Always support the work-piece on the
work table against the rotating
direction of the sanding sleeve.
All guards must be in place while
operating the sander to avoid any
injuries.
Do not use excessive force or jam a
work-piece against the sanding
surface. This can cause kick back or
damage to the machine.
Always sand work-pieces which are
stable and if you have any doubt about
the stability of the material, do not
sand it.
Make sure before making any
adjustments, the switch is in the “OFF”
position and the cord is un-plugged.
Never leave the sander unattended
while it is running.
Do not use the sanding sleeves that are
damaged or if the adhesive is not
sticking firmly. If the sanding sleeve
comes off during operation, it might
cause damage to the work-piece or
injury to the operators fingers.
Always use the table insert that fits
closest to the diameter of the installed
sanding drum. A pinch hazard exists
from the gap between the table and the
sander. Always keep this gap as small
as possible.
Do not wear loose clothing, neckties,
jewelry or gloves that can get caught in
moving parts. Confine long hair and
keep sleeves above the elbow.
Make sure you have read and
understood all the safety instructions in
the manual and you are familiar with
your sander, before operating it. If you
fail to do so, serious injury could occur.
CX508 – 14" OSCILLATING SPINDLE SANDER
SPECIFIC SAFETY INSTRUCTIONS
WARNING!
The safety instructions given above can not be complete because the environment in
every shop is different. Always consider safety first as it applies to your individual
working conditions.

5
MODEL CX508 – 14" OSCILLATING SPINDLE SANDER
As part of the growing line of Craftex CX-Series woodworking equipment, we are proud to offer
the CX508 a 14" Oscillating Spindle Sander. By following the instructions and procedures laid
out in this user manual, you will receive years of excellent service and satisfaction. The CX508
is a professional tool and like all power tools, proper care and safety procedures should be
adhered to.
Motor............................................1/4-HP, 120-V, 60-Hz
Amps............................................2.6 Amps
Power Switch...............................ON/OFF with Removable Locking Key
No Load Speed............................1725 RPM
Speed ..........................................30 OPM
Stroke ..........................................5/8"
Table Top Diameter.....................14"
Warranty......................................3 Years
CX508 – 14" OSCILLATING
SPINDLE SANDER
FEATURES

6
PHYSICAL FEATURES
Sanding
Drum
Spindle Lock
Knob
Removable
Key
Work Table
Dust Port
ON/OFF
Switch
Table Insert
Extra Sanding
Drums & Sleeves
Sanding
Sleeve
Extra Table
Inserts

7
UNPACKING
The machine is properly packaged and
shipped in a carton for safe transportation.
When unpacking, carefully inspect the
carton and ensure that it has not been
damaged during transit. Open the carton
and check that the machine and the parts
are in good condition.
NOTE: While doing inventory, if you can
not find any part, check if the part has
already been installed on the machine.
Some parts come pre-assembled for
shipping purposes.
WORKBENCH LOAD
CX508 sander is not very heavy. If using a
workbench, make sure to place the sander
on a workbench that has the capacity to
support the weight of the CX508 sander.
CLEAN UP
The unpainted surfaces of the machine are
coated with a rust preventive waxy oil to
prevent corrosion during shipment and
storage. You will need to clean up this oil
before operating the machine.
Put some cleaner or degreaser on the
unpainted areas where rust preventive oil is
and leave it for 5 minutes.
Use a rag and wipe off the oil. If the oil does
not wipe off, repeat the above steps 2 to 3
times. Once the unpainted surfaces are
clean, use metal protectant to prevent from
rust.

8
PROPER GROUNDING
Grounding provides a path of least
resistance for electric current to reduce the
risk of electric shock.
Make sure the cord is plugged into a
properly installed and grounded power
outlet. To prevent electrical hazards, have a
qualified electrician ensure that the line is
properly wired.
Make sure that the sander is connected to
an outlet having the same configuration as
the plug. If an adaptor plug is used, it must
be attached to the metal screw of the
receptacle.
Figure-1 120-volts outlet for CX508
It is strongly recommended not to use
extension cords with your CX508. Always
try to position your machine close to the
power source so that you do not need to
use extension cords.
If you really find it necessary to use an
extension cord, make sure the extension
cord does not exceed 50-feet in length and
the cord is 14-gauge to prevent motor
damage.
WARNING!
Improper connection of the equipment-
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician if you are in doubt as to
whether the outlet is properly grounded.

9
MOUNTING ON
A WORKBENCH
The CX508 features four pre-drilled holes
on its base which allow mounting the
sander to the workbench.
There are two ways to mount the sander
onto the workbench; through mount and
direct mount.
"Through Mount" is the strongest mounting
option where the holes are drilled all the
way through the workbench. Hex bolts,
washers and hex nuts are used to secure
the sander to the workbench. See figure-2.
Figure-2 Through Mount
"Direct Mount" is to simply secure the
sander to the workbench using lag screws.
See figure-3.
Figure-3 Direct Mount
SWITCH DISABLING KEY
The CX508 features a switch disabling key
which prevents from unauthorized use.
Figure-4 Switch disabling key removed
When the machine is not used for a longer
period of time, simply remove the switch
disabling key and the ON/OFF switch will
not work without it. To enable the switch,
insert the key back to its place and you will
then be able to turn ON the machine.

10
SANDING DRUM/SLEEVE
INSTALLATION
To install the sanding drum and sleeve:
Make sure the cord is disconnected from
the power source.
Hold the sanding drum and sleeve with one
hand and use the second hand to loosen
and remove the spindle lock nut.
Remove the spindle washer, sanding
sleeve, sanding drum, table insert.
Figure-5 Removing/Installing sanding drum
and sleeve
Clean the dust or debris on the table
opening.
Choose the correct size sanding drum,
sanding sleeve and table insert.
Install the desired sanding drum on the
spindle shaft, followed by the sanding
sleeve on the drum as shown in figure-5.
Secure the sanding drum with the
approximate spindle washer and spindle
lock nut. Tighten until the rubber sanding
drum places slight pressure on the sanding
sleeve.
TEST RUN
Once you have mounted your machine, it is
then time for a test run to make sure that
the machine works properly and is ready for
operation.
To test run the machine:
Make sure you have read and understood
the instructions given in the manual.
Remove and clear away all the tools and
objects from the machine.
Connect the cord to the power source and
turn ON the machine.
During the test run if there is any unusual
noise coming from the machine or the
machine vibrates excessively, shut off the
machine immediately and disconnect the
cord from the power source. Check all the
parts you have assembled, once again and
investigate to find out the problem.
If the machine runs smoothly with little or no
vibration, then it is operating correctly.
Turn OFF the sander.
Remove the switch disabling key from the
ON/OFF switch.
Try to turn ON the machine.
If the machine starts, immediately stop the
machine and unplug the cord from the
power source. Do not run the machine until
this safety feature is fixed.
If the machine does not run, it means the
switch disabling key is working properly and
test is complete.

11
SANDING
To sand with the CX508.
Turn the sander ON and allow it to reach
full speed.
Hold the work-piece with both hands and
guide it against the rotation of the spindle.
Do not force the work-piece against the
sanding sleeve.
MAINTENANCE
During the life of your machine, you will
need to practice some regular maintenance
to keep your sander in peak performance
condition.
BEFORE EACH USE
Check for any worn or damaged wires
Check the sanding drum and sleeve for any
wear or damage.
Check for any other unsafe condition
AFTER EACH USE
Turn the sander OFF.
Vacuum dust build up and clean up any
sawdust or debris from the table or other
parts of the sander.
CLEANING
Wipe off the sawdust built up from the table
surface and vacuum the dust from the
motor fan area.
Wipe or vacuum out any dust particles from
underneath the table insert and the table
opening.
The moisture from the wood dust remaining
on the table surface can cause rust. The
table and other un-painted surfaces of the
machine should be cleaned and wiped after
every use to make sure that there is no
moisture against bare metal surfaces. Then
seal with an aerosol or paste wax.
WARNING!
Make sure the machine is turned OFF
and the cord is disconnected from the
power source before servicing and
removing/replacing any components on
the machine.

12
CX508 PARTS DIAGRAM

13
CX508 PARTS LIST

14
WARRANTY
Craftex warrants every product to be free from defects in materials and agrees to correct such defects where
applicable. This warranty covers three years for parts and 90 days for labour (unless specified otherwise), to the
original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from
misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of
maintenance. Proof of purchase is necessary.
All warranty claims are subject to inspection of such products or part thereof and Craftex reserves the right to
inspect any returned item before a refund or replacement may be issued.
This warranty shall not apply to consumable products such as blades, bits, belts, cutters, chisels, punches
etceteras.
Craftex shall in no event be liable for injuries, accidental or otherwise, death to persons or damage to property or
for incidental contingent, special or consequential damages arising from the use of our products.
RETURNS, REPAIRS AND REPLACEMENTS
To return, repair, or replace a Craftex product, you must visit the appropriate Busy Bee Tools showroom or call 1-
800-461-BUSY. Craftex is a brand of equipment that is exclusive to Busy Bee Tools.
For replacement parts directly from Busy Bee Tools, for this machine, please call 1-800-461-BUSY (2879), and
have your credit card and part number handy.
All returned merchandise will be subject to a minimum charge of 15% for re-stocking and handling with the
following qualifications.
Returns must be pre-authorized by us in writing.
We do not accept collect shipments.
Items returned for warranty purposes must be insured and shipped pre-paid to the nearest warehouse
Returns must be accompanied with a copy of your original invoice as proof of purchase. Returns must be in
an un-used condition and shipped in their original packaging a letter explaining your reason for the return.
Incurred shipping and handling charges are not refundable.
Busy Bee will repair or replace the item at our discretion and subject to our inspection.
Repaired or replaced items will be returned to you pre-paid by our choice of carriers.
Busy Bee reserves the right to refuse reimbursement or repairs or replacement if a third party without our
prior authorization has carried out repairs to the item.
Repairs made by Busy Bee are warranted for 30 days on parts and labour.
Any unforeseen repair charges will be reported to you for acceptance prior to making the repairs.
The Busy Bee Parts & Service Departments are fully equipped to do repairs on all products purchased from us
with the exception of some products that require the return to their authorized repair depots. A Busy Bee
representative will provide you with the necessary information to have this done.
For faster service it is advisable to contact the nearest Busy Bee location for parts availability prior to
bringing your product in for repairs.
CRAFTEX 3 YEARS LIMITED WARRANTY