Craftmade WPS-100 User manual
WPS-100 Smart
WiFi Wall Plug
Installation Guide
WARNING:
RISK OF ELECTRIC SHOCK
This product installation requires
handling 120 volt wiring.
Follow each step carefully.
If any concerns handling wiring,
hire a qualied electrician.
Ensure all work meets local and
federal regulations.
• Download the Craftmade Smart app.
• Add your Craftmade Smart Plug
the Craftmade Smart app.
Simple DIY Setup
• Rating 120V AC 60Hz.
• Wi-Fi 802.11 b/g/n @ 2.4 GHZ is required.
• Works with compatible LED bulbs.
• 10A,1200W, General Use;1/3 HP motor
Compatibility Requirements
Alternate Connection Procedure
Smart mode networking
Preconditions: Connect to the load, reset state
long press plug 10S to reset the load)
1. Click “+” in the upper right corner (or click Add Device)
Alternate Connection Procedure (continued)
2. Select the device type as Socket (Wi-Fi)
Alternate Connection Procedure (continued)
2. Select the device type as Switch (Wi-Fi)
Alternate Connection Procedure (continued)
3. Connect to Wi-Fi, enter the password
of Wi-Fi account, and click “Next”.
Alternate Connection Procedure (continued)
4. The network is being distributed.
Alternate Connection Procedure (continued)
5. Your device should show successfully added.
WPS
Device added successfully
Alternate Connection Procedure (continued)
6. Enter the device control page.
WPS
Additional Information and Warnings
FCC Compliance Statement Compliance Notice:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are design-
ed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no gua-
rantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with part 15 of FCC rules. Operation is subject to the
following two conditions.
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference
that may cause undesired operation.
Changes or modications that are not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
CAN ICES-3 (B)/NMB-3(B)
Model: model no WPS-100
This device contains license-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
license-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1.L’appareil ne doit pas produire de brouillage;
2.L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
To maintain compliance with the RF exposure guidelines, place the
product at least 20cm from nearby persons.
Pour rester en conformité avec les consignes d’exposition aux RF,
placez le produit à au moins 20 cm des personnes proches.
CAUTION: FOR CONTROL OF INCANDESCENT OR
LED LUMINAIRES ONLY.
ATTENTION : POUR LA COMMANDE DE LUMINAIRES
A INCANDESCENTS OU LED SEULEMENT
RF Exposure information:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure
limits, human proximity to the antenna shall not be less than 8
inches during normal operation.
RF Exposure statement:
This equipment complies with IC RSS-102 radiation
exposure limits set forth for an uncontrolled environment. This
transmitter must be installed to provide a separation distance of
at least 8 inches from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter.
Déclaration d’exposition aux RF:
Cet équipement est conforme aux limites d’exposition
aux rayonnements IC RSS-102 dénies pour un environnement
non contrôlé. Cet émetteur doit être installé de manière à fournir
une distance de séparation d’au moins 8 pouces de toutes
les personnes et ne doit pas être colocalisé ou fonctionner en
conjonction avec toute autre antenne ou émetteur.
CAUTION – To reduce the risk of overheating and possible
damage to other equipment. Do not install to control a receptacle
or motor-operated appliance or transformer-suppled appliance.
Table of contents
