Craftsman 919.727121 User manual

• SAFETY GUIDELINES
• ASSEMBLY
• OPERATION
• MAINTENANCE
• TROUBLESHOOTING
• REPAIR PARTS
IMPORTANT:
Read the Safety Guidelines
and All Instructions Carefully
Before Operating
Sold by Sears Canada, Inc., Toronto, Ont. M5B 2B8
Model No.
919.727121
Record in the spaces provided.
(1) The Model Number can be found on the
maintenance label on top of the motor
shroud or on the bar code label on the
rear of air tank.
(2) The Date Code Number can be found on
the bar code label on the rear of the air
tank.
(3) The Serial Number can be found on the
bar code label on the rear of the tank.
(4) The TankRegistrationNumberislocated
on the metal data plate which is welded
onto the backside of the air tank. (This
data plate is painted the same color as
the tank.)
Retain these numbers for future reference.
Model No_______________________________
SerialNo_______________________________
DateCode______________________________
Tank Registration No____________________
D20414 Rev. 0 2/15/00
OWNERS MANUAL FOR
CRAFTSMAN
PERMANENTLY LUBRICATED
TANK MOUNTED
AIR COMPRESSOR

2 — ENG
D20414 Rev. 0 2/15/00
FULL ONE YEAR WARRANTY ON AIR COMPRESSORS
If this air compressor fails due to a defect in material or workmanship within one year from the date of
purchase, RETURN IT TO THE NEAREST SEARS SERVICE CENTER THROUGHOUT CANADA AND SEARS
WILL REPAIR IT, FREE OF CHARGE.
If this air compressor is used for commercial or rental purposes, the warranty will apply for ninety days (90)
from the date of purchase.
This Craftsman Air Compressor warranty gives you specific legal rights and you may have other rights which
vary from province to province.
Sears Canada, Inc., Toronto, Ont. M5B 2B8
WARRANTY .............................................................2
SAFETY GUIDELINES-DEFINITIONS ......................2
SAFETY GUIDELINES .......................................... 3-5
GENERAL INFORMATION .......................................6
GLOSSARY ..............................................................6
SPECIFICATION CHART .........................................6
DESCRIPTION OF OPERATION ..............................7
TOOLS NEEDED FOR ASSEMBLY ..........................7
ASSEMBLY ..............................................................8
INSTALLATION AND BREAK-IN PROCEDURES ....8
Location of Air Compressor..................................8
Lubrication and Oil ................................................8
Voltage and Circuit Protection ..............................8
Page
Extension Cords ...................................................8
Grounding Instructions .........................................9
Break-in Procedure...............................................9
OPERATING PROCEDURES .................................10
MAINTENANCE......................................................11
Check Valve -Replacement ................................11
Safety Valve - Inspection ....................................11
Storage ...............................................................11
TROUBLESHOOTING GUIDE .......................... 12-13
AIR COMPRESSOR DIAGRAM..............................14
COMPRESSOR PUMP DIAGRAM .........................16
HOW TO ORDER REPAIR PARTS .........................18
Page
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
This manual contains information that is important for you to know and understand. This information relates
to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this
information, we use the symbols to the right. Please read the manual and pay attention to these sections.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death of serious injury.
SAFETY GUIDELINES - DEFINITIONS
TABLE OF CONTENTS

3 — ENG D20414 Rev. 0 2/15/00
HAZARD
IMPORTANT SAFETY INSTRUCTIONS
RISK OF BURSTING
IT IS NORMAL FOR ELECTRICAL CONTACTS WITHIN THE
MOTOR AND PRESSURE SWITCH TO SPARK.
IF ELECTRICAL SPARKS FROM COMPRESSOR COME INTO
CONTACT WITH FLAMMABLE VAPORS, THEY MAY IGNITE,
CAUSING FIRE OR EXPLOSION.
RESTRICTING ANY OF THE COMPRESSOR VENTILATION
OPENINGS WILL CAUSE SERIOUS OVERHEATING AND
COULD CAUSE FIRE.
UNATTENDED OPERATION OF THIS PRODUCT COULD
RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.
ALWAYS OPERATE THE COMPRESSOR IN A WELL VENTI-
LATED AREA FREE OF COMBUSTIBLE MATERIALS, GASO-
LINE OR SOLVENT VAPORS.
IF SPRAYING FLAMMABLE MATERIALS, LOCATE COMPRES-
SOR AT LEAST 20 FEET AWAY FROM SPRAY AREA. AN
ADDITIONAL LENGTH OF HOSE MAY BE REQUIRED.
STORE FLAMMABLE MATERIALS IN A SECURE LOCATION
AWAY FROM COMPRESSOR.
NEVER PLACE OBJECTS AGAINST OR ON TOP OF COM-
PRESSOR. OPERATE COMPRESSOR IN AN OPEN AREA AT
LEAST 12 INCHES AWAY FROM ANY WALL OR OBSTRUC-
TION THAT WOULD RESTRICT THE FLOW OF FRESH AIR TO
THE VENTILATION OPENINGS.
OPERATE COMPRESSOR IN A CLEAN, DRY, WELL VENTILATED
AREA. DO NOT OPERATE UNIT INDOORS OR IN ANY
CONFINED AREA.
ALWAYS REMAIN IN ATTENDANCE WITH THE PRODUCT
WHEN IT IS OPERATING.
SAVE THESE INSTRUCTIONS
IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAM-
AGE. READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.
RISK OF EXPLOSION OR FIRE
AIR TANK: THE FOLLOWING CONDITIONS COULD LEAD TO A WEAKENING OF THE TANK, AND RESULT IN A
VIOLENT TANK EXPLOSION AND COULD CAUSE PROPERTY DAMAGE OR SERIOUS INJURY.
DRAIN TANK DAILY OR AFTER EACH USE. IF TANK DEVELOPS
A LEAK, REPLACE IT IMMEDIATELY WITH A NEW TANK OR
REPLACE THE ENTIRE COMPRESSOR.
NEVER DRILL INTO, WELD, OR MAKE ANY MODIFICATIONS TO
THE TANK OR ITS ATTACHMENTS.
THE TANK IS DESIGNED TO WITHSTAND SPECIFIC OPERATING
PRESSURES. NEVER MAKE ADJUSTMENTS OR PARTS
SUBSTITUTIONS TO ALTER THE FACTORY SET OPERATING
PRESSURES.
FOR ESSENTIAL CONTROL OF AIR PRESSURE, YOU MUST
INSTALL A PRESSURE REGULATOR AND PRESSURE GAUGE
TO THE AIR OUTLET OF YOUR COMPRESSOR. FOLLOW THE
EQUIPMENT MANUFACTURERS RECOMMENDATION AND NEVER
EXCEED THE MAXIMUM ALLOWABLE PRESSURE RATING OF
ATTACHMENTS. NEVER USE COMPRESSOR TO INFLATE SMALL
LOW-PRESSURE OBJECTS SUCH AS CHILDREN’S TOYS,
FOOTBALLS, BASKETBALLS. ETC.
1. FAILURE TO PROPERLY DRAIN CONDENSED WATER
FROM THE TANK, CAUSING RUST AND THINNING OF THE
STEEL TANK.
2. MODIFICATIONS OR ATTEMPTED REPAIRS TO THE TANK.
3. UNAUTHORIZED MODIFICATIONS TO THE UNLOADER
VALVE, SAFETY VALVE, OR ANY OTHER COMPONENTS
WHICH CONTROL TANK PRESSURE.
4. EXCESSIVE VIBRATION CAN WEAKEN THE AIR TANK AND
CAUSE RUPTURE OR EXPLOSION.
ATTACHMENTS & ACCESSORIES:
EXCEEDING THE PRESSURE RATING OF AIR TOOLS, SPRAY
GUNS, AIR OPERATED ACCESSORIES, TIRES AND OTHER
INFLATABLES CAN CAUSE THEM TO EXPLODE OR FLY
APART, AND COULD RESULT IN SERIOUS INJURY.
WHAT CAN HAPPEN HOW TO PREVENT IT
WHAT CAN HAPPEN HOW TO PREVENT IT

4 — ENG
D20414 Rev. 0 2/15/00
WHAT CAN HAPPEN HOW TO PREVENT IT
RISK FROM FLYING OBJECTS
THE COMPRESSED AIR STREAM CAN CAUSE SOFT TISSUE
DAMAGE TO EXPOSED SKIN AND CAN PROPEL DIRT, CHIPS,
LOOSE PARTICLES AND SMALL OBJECTS AT HIGH SPEED,
RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY.
ALWAYS WEAR ANSI Z87.1 APPROVED SAFETY GLASSES WITH
SIDE SHIELDS WHEN USING THE COMPRESSOR.
NEVER POINT ANY NOZZLE OR SPRAYER TOWARD ANY PART
OF THE BODY OR AT OTHER PEOPLE OR ANIMALS.
ALWAYS TURN THE COMPRESSOR OFF AND BLEED PRESSURE
FROM THE AIR HOSE AND TANK BEFORE ATTEMPTING MAINTE-
NANCE, ATTACHING TOOLS OR ACCESSORIES.
THE COMPRESSED AIR FROM YOUR COMPRESSOR IS NOT
SAFE FOR BREATHING! THE AIR STREAM MAY CONTAIN
CARBON MONOXIDE, TOXIC VAPORS OR SOLID PARTICLES
FROM THE TANK.
SPRAYED MATERIALS SUCH AS PAINT, PAINT SOLVENTS, PAINT
REMOVER, INSECTICIDES, WEED KILLERS, CONTAIN HARMFUL
VAPORS AND POISONS.
ALWAYS OPERATE AIR COMPRESSOR OUTSIDE IN A CLEAN,
WELL VENTILATED AREA. AVOID ENCLOSED AREAS SUCH AS
GARAGES, BASEMENTS, STORAGE SHEDS, WHICH LACK A
STEADY EXCHANGE OF AIR. KEEP CHILDREN, PETS AND OTHERS
AWAY FROM AREA OF OPERATION.
NEVER INHALE AIR FROM THE COMPRESSOR EITHER DI-
RECTLY OR FROM A BREATHING DEVICE CONNECTED TO THE
COMPRESSOR.
WORK IN AN AREA WITH GOOD CROSS-VENTILATION. READ
AND FOLLOW THE SAFETY INSTRUCTIONS PROVIDED ON THE
LABEL OR SAFETY DATA SHEETS FOR THE MATERIAL YOU ARE
SPRAYING. USE A NIOSH/MSHA APPROVED RESPIRATOR
DESIGNED FOR USE WITH YOUR SPECIFIC APPLICATION.
HAZARD
WHAT CAN HAPPEN HOW TO PREVENT IT
RISK TO BREATHING
YOUR AIR COMPRESSOR IS POWERED BY ELECTRICITY. LIKE
ANY OTHER ELECTRICALLY POWERED DEVICE, IF IT IS NOT
USED PROPERLY IT MAY CAUSE ELECTRIC SHOCK.
REPAIRS ATTEMPTED BY UNQUALIFIED PERSONNEL CAN
RESULT IN SERIOUS INJURY OR DEATH BY ELECTROCUTION.
ELECTRICAL GROUNDING: FAILURE TO PROVIDE ADEQUATE
GROUNDING TO THIS PRODUCT COULD RESULT IN SERIOUS
INJURY OR DEATH FROM ELECTROCUTION. SEE GROUNDING
INSTRUCTIONS.
NEVER OPERATE THE COMPRESSOR OUTDOORS WHEN IT IS
RAINING OR IN WET CONDITIONS.
NEVER OPERATE COMPRESSOR WITH COVER COMPONENTS
REMOVED OR DAMAGED.
ANY ELECTRICAL WIRING OR REPAIRS REQUIRED ON THIS
PRODUCT SHOULD BE PERFORMED BY AUTHORIZED SERVICE
CENTER PERSONNEL IN ACCORDANCE WITH NATIONAL AND
LOCAL ELECTRICAL CODES.
MAKE CERTAIN THAT THE ELECTRICAL CIRCUIT TO WHICH
THE COMPRESSOR IS CONNECTED PROVIDES PROPER
ELECTRICAL GROUNDING, CORRECT VOLTAGE AND AD-
EQUATE FUSE PROTECTION.
WHAT CAN HAPPEN HOW TO PREVENT IT
RISK OF ELECTRICAL SHOCK

5 — ENG D20414 Rev. 0 2/15/00
MOVING PARTS SUCH AS THE PULLEY, FLYWHEEL AND BELT
CAN CAUSE SERIOUS INJURY IF THEY COME INTO CONTACT
WITH YOU OR YOUR CLOTHING.
ATTEMPTING TO OPERATE COMPRESSOR WITH DAMAGED
OR MISSING PARTS OR ATTEMPTING TO REPAIR COMPRES-
SOR WITH PROTECTIVE SHROUDS REMOVED CAN EXPOSE
YOU TO MOVING PARTS AND CAN RESULT IN SERIOUS
INJURY.
NEVER OPERATE THE COMPRESSOR WITH GUARDS OR
COVERS WHICH ARE DAMAGED OR REMOVED.
ANY REPAIRS REQUIRED ON THIS PRODUCT SHOULD BE
PERFORMED BY AUTHORIZED SERVICE CENTER PERSONNEL.
HAZARD
RISK FROM MOVING PARTS
WHAT CAN HAPPEN HOW TO PREVENT IT
TOUCHING EXPOSED METAL SUCH AS THE COMPRESSOR
HEAD OR OUTLET TUBES, CAN RESULT IN SERIOUS BURNS.
NEVER TOUCH ANY EXPOSED METAL PARTS ON COMPRES-
SOR DURING OR IMMEDIATELY AFTER OPERATION. COMPRES-
SOR WILL REMAIN HOT FOR SEVERAL MINUTES AFTER
OPERATION.
DO NOT REACH AROUND PROTECTIVE SHROUDS OR ATTEMPT
MAINTENANCE UNTIL UNIT HAS BEEN ALLOWED TO COOL.
WHAT CAN HAPPEN HOW TO PREVENT IT
A PORTABLE COMPRESSOR CAN FALL FROM A TABLE,
WORKBENCH OR ROOF CAUSING DAMAGE TO THE COMPRES-
SOR AND COULD RESULT IN SERIOUS INJURY OR DEATH TO
THE OPERATOR.
ALWAYS OPERATE COMPRESSOR IN A STABLE SECURE
POSITION TO PREVENT ACCIDENTAL MOVEMENT OF THE UNIT.
NEVER OPERATE COMPRESSOR ON A ROOF OR OTHER
ELEVATED POSITION. USE ADDITIONAL AIR HOSE TO REACH
HIGH LOCATIONS.
WHAT CAN HAPPEN HOW TO PREVENT IT
OIL CAN LEAK OR SPILL AND COULD RESULT IN FIRE OR
BREATHING HAZARD, SERIOUS INJURY OR DEATH CAN RESULT.
OIL LEAKS WILL DAMAGE CARPET, PAINT OR OTHER SURFACES
IN VEHICLES OR TRAILERS.
WHAT CAN HAPPEN HOW TO PREVENT IT
ALWAYS PLACE COMPRESSOR ON A PROTECTIVE MAT WHEN
TRANSPORTING TO PROTECT AGAINST DAMAGE TO VEHICLE
FROM LEAKS. REMOVE COMPRESSOR FROM VEHICLE IMMEDI-
ATELY UPON ARRIVAL AT YOUR DESTINATION.
RISK OF PROPERTY DAMAGE WHEN TRANSPORTING
COMPRESSOR
(Fire, Inhalation, Damage to Vehicle Surfaces)
RISK OF BURNS
ESW-99  9/26/99
RISK OF FALLING

6 — ENG
D20414 Rev. 0 2/15/00
Your air compressor can be used for operating paint
spray guns, air tools, blow guns, nailers/staplers, air
brushes, and inflator kits. An air pressure regulator is
required for most of the applications.
An in-line air filter which removes moisture and dirt
from compressed air should be used where applicable.
An in-line regulator can be used if a more precise
adjustment of air pressure is needed downstream.
CFM: Cubic Feet per Minute.
SCFM: Standard Cubic Feet per Minute; a unit of
measure of air delivery.
PSI: Pounds per Square Inch; a unit of measure of
pressure.
ASME: American Society of Mechanical Engineers;
made, tested, inspected and registered to meet the
standards of the ASME.
Cut-In Pressure: While the motor is off, air tank
pressure drops as you continue to use your acces-
sory. When the tank pressure drops to a certain low
level and the pressure switch lever is in "Auto", the
motor will restart automatically. The low pressure at
which the motor automatically restarts is called “cut-
in pressure.”
SPECIFICATION CHART
You have purchased an air compressor unit consist-
ing of a one cylinder, single-stage air compressor
pump and air tank. Included are wheels, regulator,
and gauges.
This air compressor requires no oil. Now you can
enjoy all the benefits of having an air compressor
without ever having to purchase, add or change oil.
Model No.
Bore
Stroke
Voltage - Single Phase
Minimum Branch Circuit Requirement
Fuse Type
Air Tank
/ Capacity
Approximate Cut-in Pressure
Approximate Cut-out Pressure
SCFM @ 40 psi
SCFM @ 90 psi
919.727121
1 7/8"
1 1/4"
120
10 amps
Time Delay
12 gal. (U.S.)
100
125
3.7
2.6
Cut-Out Pressure: When you turn on your air com-
pressor and it begins to run, air pressure in the air tank
begins to build. It builds to a certain high pressure
before the motor automatically shuts off - protecting
your air tank from pressure higher than its capacity.
The high pressure at which the motor shuts off is called
“cut-out pressure.”
CSA: Electrical products sold in Canada are required
to be certified to the applicable CSA standard (s).
Canadian Standards Association (CSA) is a standards
writing and safety testing organization. Products that
are CSA certified have been evaluated and tested and
found to meet or exceed the applicable CSA standard
(s) for safety and electrical performance.
GENERAL INFORMATION
GLOSSARY

7 — ENG D20414 Rev. 0 2/15/00
Safety Valve: If the pressure switch does not shut
off the air compressor at its cut-out pressure setting,
the safety valve will protect the tank against high
pressure by “popping out” at its factory set pressure
(slightly higher than the pressure switch cut-out
setting).
Regulator: The air pressure coming from the air tank
is controlled by the regulator. Turn the regulator knob
clockwise to increase pressure and counter-clock-
wise to decrease pressure. To avoid minor readjust-
ment after making a change in pressure setting,
always approach the desired pressure from a lower
pressure. When reducing from a higher to a lower
setting, first reduce to some pressure less than that
desired, then bring up to the desired pressure.
Depending on the air requirements of each particular
accessory, the outlet regulated air pressure may have
to be adjusted while operating the accessory.
Outlet Pressure Gauge: The outlet pressure gauge
indicates the air pressure available at the outlet side
of the regulator. This pressure is controlled by the
regulator and is always less or equal to the tank
pressure. See “Operating Procedures”.
Tank Pressure Gauge: The tank pressure gauge
indicates the reserve air pressure in the tank.
Cooling System: This compressor contains an
advanced design cooling system. At the heart of this
cooling system is an engineered fan. It is perfectly
normal for this fan to blow air through the vent holes
in large amounts. You know that the cooling system
is working when air is being expelled.
Air Compressor Pump: To compress air, the piston
moves up and down in the cylinder. On the down-
stroke, air is drawn in through the air intake valves.
The exhaust valves remain closed. On the upstroke of
the piston, air is compressed. The intake valves close
and compressed air is forced out through the exhaust
valves, through the outlet tube, through the check valve
and into the air tank. Working air is not available until
the compressor has raised the air tank pressure above
that required at the air outlet.
Check Valve: When the air compressor is operating,
the check valve is “open”, allowing compressed air to
enter the air tank. When the air compressor reaches
“cut-out” pressure, the check valve “closes”, allowing
air pressure to remain inside the air tank.
Pressure Release Valve: The pressure release valve
located on the side of the pressure switch, is designed
to automatically release compressed air from the
compressor head and the outlet tube when the air
compressor reaches “cut-out” pressure or is shut off.
If the air is not released, the motor will not be able to
start. The pressure release valve allows the motor to
restart freely. When the motor stops running, air will be
heard escaping from the valve for a few seconds. No
air should be leaking when the motor is running.
Pressure Switch: The pressure switch automatically
starts the motor when the air tank pressure drops
below the factory set “cut-in” pressure. It stops the
motor when the air tank pressure reaches the factory
set “cut-out” pressure.
• a 3/8" open end wrench or socket to tighten handle
screws
• a 9/16" socket or open end wrench for attaching
the wheels
DESCRIPTION OF OPERATION
TOOLS NEEDED FOR ASSEMBLY

8 — ENG
D20414 Rev. 0 2/15/00
INSTALLATION AND BREAK-IN PROCEDURES
Location of the Air Compressor
Locate the air compressor in a clean, dry and well
ventilated area. The air compressor should be
located at least 12" away from the wall or other
obstructions that will interfere with the flow of air. The
air compressor pump and shroud are designed to
allow for proper cooling. The ventilation openings on
the compressor are necessary to maintain proper
operating temperature. Do not place rags or other
containers on or near these openings.
Lubrication and Oil
This unit needs no lubrication or oiling.
Voltage and Circuit Protection
Refer to your Parts List Manual for the voltage and
circuit protection requirements of your compressor.
Use only a fuse or circuit breaker that is the same
rating as the branch circuit the air compressor is
operated on. If the compressor is connected to
a circuit protected by fuses, use only dual element
time delay fuses, as noted in that Service Bulletin.
Refer to Parts List Manual for your compressor.
Certain air compressor models can be operated on a
15 amp circuit if:
1. Voltage supply to circuit is normal.
ASSEMBLY
Installing Wheels, Handles, Molded Foot
Bumpers
THE WHEELS AND HANDLE DO NOT
PROVIDE ADEQUATE CLEARANCE,
STABILITY OR SUPPORT FOR PULLING
THE UNIT UP AND DOWN STAIRS OR
STEPS. THE UNIT MUST BE LIFTED, OR
PUSHED UP A RAMP.
1. Attach the handle to the compressor saddle by
inserting the handle inside the compressor
saddle and lining up the bolt holes on each side.
Install the two screws, one on each side. Tighten
securely.
It will be necessary to brace or support one
side of the outfit when installing the wheels
because the compressor will have a ten-
dency to tip over.
2. Install one shoulder bolt and one nut for each
wheel. Tighten securely. The outfit will sit level if the
wheels are properly installed.
3. Clean and dry underside of air tank leg opposite
wheels. Remove the protective strip from the
adhesive backed molded foot bumpers. Attach the
foot bumpers to the bottom of leg on each end.
Press firmly into place.
2. Circuit is not used to supply any other electrical
needs (lights, appliances, etc.).
3. Extension cords comply with specifications.
4. Circuit is equipped with a 15 amp circuit breaker or
15 amp time delay fuse.
If any of the above conditions cannot be met, or if
operation of the compressor repeatedly causes inter-
ruption of the power, it may be necessary to operate it
from a 20 amp circuit. It is not necessary to change the
cord set.
Extension Cords
Use extra air hose instead of an extension cord to
avoid voltage drop and power loss to the motor, and to
prevent overheating.
If an extension cord must be used, be sure it is:
• a 3-wire extension cord that has a 3-blade ground-
ing plug, and a 3-slot receptacle that will accept the
plug on the product
• in good condition
• no longer than 50 feet
• 12 gauge (AWG) or larger. (Wire size increases as
gauge number decreases. 10 AWG and 8 AWG
may also be used. DO NOT USE 14 OR 16 AWG.)

9 — ENG D20414 Rev. 0 2/15/00
Break-in Procedure
Serious damage may result if the following
break-in instructions are not closely
followed.
This procedure is required only once, before the air
compressor is put into service.
1. Set the pressure switch OFF/AUTO lever in the
"OFF" position.
2. Plug the power cord into the correct branch
circuit receptacle.
3. Turn the regulator clockwise, opening it fully, to
prevent air pressure build-up in the tank.
4. Move the OFF/AUTO lever to "AUTO". The
compressor will start.
5. Run the compressor for 15 minutes. Make sure
the regulator is open and there is no tank pres-
sure build-up.
6. After 15 minutes, close the regulator by turning it
counterclockwise. The air tank will fill to cut-out
pressure and then the motor will stop.
Refer to "Operating Procedures".
GROUNDING INSTRUCTIONS
RISK OR ELECTRICAL SHOCK. In the event
of a short circuit, grounding reduces the risk
of shock by providing an escape wire for the
electric current. This air compressor must
be properly grounded.
The portable air compressor is equipped with a cord
having a grounding wire with an appropriate grounding
plug. The plug must be used with an outlet that has
been installed and grounded in accordance with all
local codes and ordinances. The outlet must have the
same configuration as the plug. DO NOT USE AN
ADAPTER TO DEFEAT THE GROUNDING FEATURE
OF THE PLUG.
Inspect the plug and cord before each use. Do not use
if there are signs of damage.
IMPROPER GROUNDING CAN RESULT IN
ELECTRICAL SHOCK.
Do not modify the plug that has been pro-
vided. If it does not fit the available outlet,
the correct outlet should be installed by a
qualified electrician.
If repairing cord or plug, the grounding wire must be
kept separate from the current-carrying wires. Never
connect the grounding wire to a flat blade plug
terminal. The grounding wire has insulation with an
outer surface that is green - with or without yellow
stripes.
If these grounding instructions are not completely
understood, or if in doubt as to whether the compres-
sor is properly grounded, have the installation
checked by a qualified electrician.

10 — ENG
D20414 Rev. 0 2/15/00
OPERATING PROCEDURES
1. Before attaching air hose or accessories, make
sure the OFF/AUTO lever is set to “OFF” and the
air regulator is closed.
2. Attach hose and accessories.
TOO MUCH AIR PRESSURE CREATES A
HAZARDOUS RISK OF BURSTING. CARE-
FULLY FOLLOW STEPS 3 AND 5 EACH
TIME THE COMPRESSOR IS USED.
Compressed air from the outfit may
contain water condensation. Do not spray
unfiltered air at an item that could be
damaged. Some air operated tools or
devices may require filtered air. Read the
instructions for the air tool or device.
3. Check the manufacturer’s maximum pressure
rating for air tools and accessories. The regula-
tor outlet pressure must never exceed the
maximum pressure rating. If your compressor is
not supplied with a regulator with gauge, install
one before using accessories.
4. Turn the OFF/AUTO lever to “AUTO” and allow
tank pressure to build. Motor will stop when tank
pressure reaches “cut-out” pressure.
5. Open the regulator by turning it clockwise.
Adjust the regulator to the correct pressure
setting. Your compressor is ready for use.
6. Always operate the air compressor in well-venti-
lated areas; free of gasoline or other solvent
vapors.
Do not operate the compressor near the spray
area.
When you are finished:
7. Set the “OFF/AUTO” lever to “OFF”.
8. Turn the regulator counterclockwise and set the
outlet pressure to zero.
9. Remove the air tool or accessory.
10. Open the regulator and allow the air to slowly bleed
from the tank. Close the regulator when tank
pressure is approximately 20 psi.
11. Drain water from air tank.
WATER WILL CONDENSE IN THE AIR TANK.
IF NOT DRAINED, WATER WILL CORRODE
AND WEAKEN THE AIR TANK CAUSING A
RISK OF AIR TANK RUPTURE.
With tank pressure at approximately 20 psi, open the drain
cock or drain valve.
NOTE:
If drain cock valve is plugged, release all air
pressure. The valve can then be removed,
cleaned, then reinstalled.
12. After the water has been drained, close drain cock
or drain valve. The air compressor can now be
stored.

11 — ENG D20414 Rev. 0 2/15/00
ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE DONE BY QUALIFIED SERVICE PERSONNEL.
Safety Valve - Inspection
If the safety valve does not work properly,
over-pressurization may occur, causing air
tank rupture or an explosion. Before
starting compressor, pull the ring on the
safety valve to make sure that the safety
valve operates freely. If the valve is stuck
or does not operate smoothly, it must be
replaced with the same type of valve.
Storage
Before you store the air compressor, make sure you
do the following:
1. Review the “Maintenance” and "Operating
Procedures" sections and perform maintenance
as necessary. Be sure to drain water from the air
tank.
2. Protect the electrical cord and air hose from
damage (such as being stepped on or run over).
Wind them loosely around the compressor
handle.
Store the air compressor in a clean and dry location.
Check Valve - Replacement
Before servicing:
• Unplug or disconnect electrical supply
to compressor.
• Bleed tank of pressure.
• Allow compressor to cool.
1. Release all air pressure from air tank and unplug
outfit.
2. Loosen the bottom nut and move the outlet tube to
the side.
3. Unscrew the check valve (turn counterclockwise)
using a socket wrench.
4. Check that the valve disc moves freely inside the
check valve and that the spring holds the disc in
the upper, closed position. The check valve may be
cleaned with a solvent, such as paint and varnish
remover.
5. Apply sealant to the check valve threads. Reinstall
the check valve (turn clockwise).
6. Replace the outlet tube and tighten the bottom nut.
MAINTENANCE
UNIT CYCLES AUTOMATICALLY WHEN POWER IS ON. WHEN DOING MAINTENANCE, YOU MAY
BE EXPOSED TO VOLTAGE SOURCES, COMPRESSED AIR OR MOVING PARTS. PERSONAL
INJURIES CAN OCCUR. BEFORE PERFORMING ANY MAINTENANCE OR REPAIR, UNPLUG THE
COMPRESSOR AND BLEED OFF ALL AIR PRESSURE.

12 — ENG
D20414 Rev. 0 2/15/00
Torque head screws to 8 ft. lbs. If this does not
stop leak, replace seal.
CAUSE CORRECTION
Excessive tank pressure -
safety valve pops off.
Pressure switch does not shut off
motor when compressor reaches
“cut-out” pressure.
Move the pressure switch lever to the “OFF”
position. If the outfit doesn’t shut off, and the
electrical contacts are welded together, replace
the pressure switch.
Return the outfit to Sears Service Center to check
and adjust, or replace switch.
Tube fittings are not tight enough. Tighten fittings where air can be heard escaping.
Check fittings with soapy water solution. DO NOT
OVERTIGHTEN.
PROBLEM
Air leaks at fittings.
Pressure switch “cut-out” too high.
Defective pressure switch release
valve.
Remove and replace the release valve.
Check to see if the pin in the bottom of the
pressure release valve is stuck. If it does not move
freely, replace the valve.
Air leaks at pressure switch
release valve.
If there is an excessive amount of pressure drop
when the accessory is used, adjust the regulator
following the instructions on page 7.
TROUBLESHOOTING GUIDE
PERFORMING REPAIRS MAY EXPOSE VOLTAGE SOURCES, MOVING PARTS OR COMPRESSED
AIR SOURCES. PERSONAL INJURY MAY OCCUR. PRIOR TO ATTEMPTING ANY REPAIRS, UN-
PLUG THE COMPRESSOR AND BLEED OFF TANK AIR PRESSURE.
Inspect and replace upper manifold assembly.
Check valve seat damaged.
Defective air tank.Air leaks in air tank or at air tank
welds.
DO NOT DRILL INTO, WELD OR OTHER-
WISE MODIFY AIR TANK OR IT WILL
WEAKEN. THE TANK CAN RUPTURE OR
EXPLODE.
Air leaks between head and
valve plate. Leaking seal.
Pressure reading on the
regulated pressure gauge
drops when an accessory is
used.
It is normal for “some” pressure
drop to occur.
NOTE
Adjust the regulated pressure under flow
conditions (while accessory is being used).
A defective flapper valve results in a constant air
leak at the pressure release valve when there is
pressure in the tank and the compressor is shut
off. Remove and clean or replace valve.
Air tank must be replaced. Do not repair the leak.
Defective flapper valve in manifold.

13 — ENG D20414 Rev. 0 2/15/00
CORRECTION
CAUSE
Air leaks.
Air leak from safety valve. Operate safety valve manually by pulling on ring. If
valve still leaks, it should be replaced.
Have checked at local Sears Service Center.
Compressor is not supplying
enough air to operate
accessories.
Compressor is not large enough for
air requirement.
Check the accessory air requirement. If it is higher
than the SCFM or pressure supplied by your air
compressor, you need a larger compressor.
Restricted air intake filter.
Check and replace if required.
Check valve restricted. Remove and clean, or replace.
Hole in hose.
Clean or replace air intake filter. Do not operate the
air compressor in the paint spray area.
Decrease amount of air usage.
Prolonged excessive use of air.
Knocking Noise Defective check valve.
Possible defect in safety valve.
Fuse blown, circuit breaker tripped.
Extension cord is wrong length or
gauge.
Loose electrical connections.
Faulty motor.
PROBLEM
Regulator knob continuous air
leak. Regulator will not shut off
at air outlet.
Dirty or damaged regulator internal
parts.
Clean or replace regulator, or internal parts.
Check fuse box for blown fuse and replace as neces-
sary. Reset circuit breaker. Do not use a fuse or circuit
breaker with higher rating than that specified for
your particular branch circuit.
Check for proper fuse. You should be using a Quick
Acting fuse.
Check for low voltage problem.
Check for the extension cord.
Disconnect the other electrical appliances from cir-
cuit or operate the compressor on its own branch
circuit.
Check the extension cord.
Check wiring connection inside terminal box.
Have checked at local Sears Service Center.
TROUBLESHOOTING GUIDE (Continued)
Tighten fittings. (See Air Leaks Section of Trouble-
shooting Guide.)
Motor will not run.

OWNERS MANUAL FOR
PERMANENTLY LUBRICATED
TANK MOUNTED
AIR COMPRESSOR
Sold By Sears Canada, Inc., Toronto, Ont. M5B 2B8
The model number of your Sears Air Compressor can be found
on the maintenance label on the top of the shroud or on the bar
code label on the rear of the air tank.
HOW TO ORDER
REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
• PART NUMBER • PART DESCRIPTION
• MODEL NUMBER • NAME OF ITEM
All parts listed may be ordered from any Sears Service Center
and most Sears stores.
If the parts you need are not stocked locally, your order will be
electronically transmitted to a Sears Repair Parts Distribution
Center for handling.
SERVICE SERVICE AND REPAIR PARTS
CALL 1-800-665-4455*
Keep this number handy should you require a service call or need to
order repair parts.
If ordering parts make sure you have the name, make and model no.
of the merchandise and the name and number of
the part you wish to order.
*If calling locally, please use one of the following numbers:
Regina - 566-5124 Montreal - 333-5740
Toronto - 744-4900 Halifax - 454-2444
Kitchener - 894-7590 Ottawa - 738-4440
Vancouver - 420-8211
Model No.
919.727121

IMPORTANT :
Lire attentivement toutes les
instructions et les mesures de
sécuritéavant d’utiliser
l’appareil.
Vendu par Sears Canada, Inc., Toronto, Ont. M5B 2B8
Modèle no.
919.727121
Inscrivez dans l’espace réservéàcette fin
1) Le numéro du modèle se trouve sur l’étiquette
d’entretien qui est sur le dessus du carter du
moteur ou sur l’étiquette de caractères à
bâtonnets située àl’arrière du réservoir d’air.
2) Le numéro de code datése trouve sur l’étiquette
de caractères àbâtonnets située àl’arrière du
réservoir d’air.
3) Le numéro de série se trouve sur l’étiquette de
caractères àbâtonnets située àl’arrière du
réservoir d’air.
4) Le numéro d’enregistrement du réservoir se
trouve sur la plaque signélatique de métal
soudée àl’arrière du réservoir d’air. (Cette
plaque signélatique est peinte de la même
couleur que le réservoir.
Conservez ces numéros pour référence ultérieure.
Modèle no: __________________________________
Numéro de série : ___________________________
Code daté: _________________________________
Enregistrement du réservoir no: ______________
D20414 Rev. 0 2/15/00
GUIDE DE L’UTILISATEUR
POUR LE COMPRESSEUR D’AIR
À LUBRIFICATION PERMANENTE
MONTÉ SUR RÉSERVOIR
DE CRAFTSMAN
•MESURES DE SÉCURITÉ
•ASSEMBLAGE
•FONCTIONNEMENT
•ENTRETIEN
•GUIDE DE DÉPANNAGE
•PIÈCES DE RECHANGE

D20414 Rev. 0 2/15/00 2-FR
GARANTIE ....................................................................... 2
MESURES DE SÉCURITÉ- DÉFINITIONS ................... 2
MESURES DE SÉCURITÉ.......................................... 3-5
RENSEIGNEMENTS GÉNÉRAUX .................................. 6
LEXIQUE .......................................................................... 6
TABLEAU DES SPÉCIFICATIONS ................................. 6
DESCRIPTION DU MODE OPÉRATIONNEL................. 7
OUTILS REQUIS ÀL’INSTALLATION............................ 7
ASSEMBLAGE ................................................................. 8
INSTALLATION ET PROCÉDURES
DE MISE EN ROUTE ....................................................... 8
Emplacement du compresseur d’air ............................ 8
Lubrification et huile ..................................................... 8
GARANTIE COMPLÈTE DE UN AN SUR LES COMPRESSEURS D’AIR
Ce compresseur d’air est garanti contre tout défaut de fabrication pour une période de un an, àcompter de la
date d’achat. Au cours de cette période de garantie, SEARS S’ENGAGE ÀLE RÉPARER SANS FRAIS. IL SUFFIT
DE LE RETOURNER AU CENTRE DE SERVICE APRÈS-VENTE SEARS LE PLUS PROCHE. LES CENTRES DE
SERVICE APRÈS-VENTE SONT RÉPARTIS DANS TOUT LE CANADA.
Cette garantie ne s’applique que pour une période de quatre-vingt-dix (90) jours seulement, àcompter de la
date d’achat, sur un compresseur qui est utiliséàdes fins commerciales ou comme appareil de location
Cette garantie sur le compresseur d'air de Craftsman vous donne des droits particuliers. Il se peut que vous
ayez d’autres droits qui varient d’une province àl’autre.
Sears Canada, Inc., Toronto, Ont. M5B 2B8
MISE EN GARDE : Indique la possibilitéd’un danger qui, s’il n’est
pas évitépeut causer des blessures mineures ou moyennes.
Ce guide contient des renseignements importants que vous devez bien saisir. Cette information porte sur VOTRE SÉCURITÉet sur LA PRÉVENTION
DE PROBLÈMES D’ÉQUIPEMENT. Afin de vous aider àidentifier cette information, nous avons utilisédes signes de danger plus bas. Veuillez lire
attentivement ce guide en portant une attention particulière àces sections. CONSERVEZ CES DÉFINITIONS/INSTRUCTIONS.
DANGER : Indique un danger imminent qui, s'il n'est pas évité,
causera de graves blessures ou la mort.
MISE EN GARDE (sans le symbole d'attention) : Indique la
possibilitéd'un danger qui, s'il n'est pas évité, peut causer des
dommages àla propriété.
AVERTISSEMENT : Indique la possibilitéd’un danger qui, s’il
n’est pas évité, pourrait causer de graves blessures ou la mort.
MESURES DE SÉCURITÉ - DÉFINITIONS
AVERTISSEMENT
MISE EN GARDE
MISE EN GARDE
DANGER
TABLE DES MATIÈRES
Tension et protection du circuit ................................... 8
Rallonges ...................................................................... 8
Directives de mise àla terre ......................................... 9
Procédures de mise en route ....................................... 9
PROCÉDURES OPÉRATIONNELLES.......................... 10
ENTRETIEN ................................................................... 11
Soupape de retenue –Remplacement ....................... 11
Soupape de sûreté- Vérification ................................ 11
Entreposage ................................................................ 11
GUIDE DE DÉPANNAGE ........................................ 12-13
DIAGRAMME DU COMPRESSEUR D’AIR .................. 14
DIAGRAMME DE LA POMPE DU COMPRESSEUR ... 16
COMMENT PLACER UNE COMMANDE
DE PIÈCES DE RECHANGE ......................................... 18

D20414 Rev. 0 2/15/00
3-FR
RISQUE D’ÉCLATEMENT
LES ÉTINCELLES QUI PROVIENNENT DES CONTACTS ÉLECTRIQUES DU
MOTEUR ET DU MANOSTAT SONT CONSIDÉRÉES NORMALES.
SI DES ÉTINCELLES ÉLECTRIQUES DU COMPRESSEUR ENTRENT EN
CONTACT AVEC DES VAPEURS INFLAMMABLES, ELLES PEUVENT
S’ENFLAMMER, PROVOQUANT UN INCENDIE OU UNE EXPLOSION.
TOUTE OBSTRUCTION DES ORIFICES D’AÉRATION DU COMPRESSEUR
ENTRAÎNERA UNE SURCHAUFFE DANGEREUSE ET RISQUE DE CAUSER
UN INCENDIE.
.
SI CET APPAREIL FONCTIONNE SANS SUPERVISION, CELA RISQUE DE
CAUSER DES BLESSURES GRAVES OU DES DOMMAGES ÀLA PROPRIÉTÉ.
TOUJOURS UTILISER LE COMPRESSEUR DANS UN ENDROIT BIEN AÉRÉ,
LOIN DE TOUTE MATIÈRE COMBUSTIBLE ET DES VAPEURS D’ESSENCE
OU DE SOLVANTS.
SI DES MATIÈRES INFLAMMABLES DOIVENT ÊTRE VAPORISÉES, SITUER LE
COMPRESSEUR ÀUNE DISTANCE D’AU MOINS 20 PIEDS DE LA ZONE DE
VAPORISATION. IL PEUT S’AVÉRER NÉCESSAIRE D’UTILISER UN BOYAU
SUPPLÉMENTAIRE.
ENTREPOSER LES MATIÈRES INFLAMMABLES DANS UN ENDROIT
SÉCURITAIRE, LOIN DU COMPRESSEUR.
NE JAMAIS PLACER DES OBJETS CONTRE OU SUR LE COMPRESSEUR.
UTILISER LE COMPRESSEUR DANS UN ENDROIT OUVERT, ÀAU MOINS 12
POUCES (30 cm) DE TOUT MUR OU OBSTRUCTION QUI RÉDUIT LE DÉBIT
D’AIR FRAIS VERS LES ORIFICES D’AÉRATION.
UTILISER LE COMPRESSEUR DANS UN ENDROIT PROPRE. NE PAS UTILISER
L’APPAREIL ÀL’INTÉRIEUR OU DANS UN ENDROIT CLOS.
TOUJOURS RESTER ÀPROXIMITÉDE L’APPAREIL LORSQU’IL EST EN
FONCTION.
RISQUE D’EXPLOSION OU D’INCENDIE
RÉSERVOIR D’AIR : LES CONDITIONS SUIVANTES PEUVENT AFFAIBLIR LES PAROIS DU RÉSERVOIR ET PROVOQUER UNE
EXPLOSION VIOLENTE DU RÉSERVOIR QUI RISQUE DE CAUSER DES DOMMAGES ÀLA PROPRIÉTÉ
OU DES BLESSURES GRAVES.
PURGER LE RÉSERVOIR QUOTIDIENNEMENT OU APRÈS CHAQUE
UTILISATION. SI LE RÉSERVOIR ACCUSE UNE FUITE, LE REMPLACER
IMMÉDIATEMENT PAR UN NOUVEAU RÉSERVOIR OU REMPLACER LE
COMPRESSEUR AU COMPLET.
NE JAMAIS PERFORER AVEC UNE PERCEUSE, SOUDER OU FAIRE UNE
MODIFICATION QUELCONQUE AU RÉSERVOIR OU ÀSES ACCESSOIRES.
LE RÉSERVOIR EST CONÇU POUR SUBIR DES PRESSIONS DE SERVICE
PARTICULIÈRES. NE JAMAIS EFFECTUER DES RÉGLAGES NI SUBSTITUER
DES PIÈCES POUR MODIFIER LES PRESSIONS DE SERVICE ÉTABLIES À
L’USINE.
POUR LE CONTRÔLE ESSENTIEL DE LA PRESSION D’AIR, IL FAUT POSER UN
RÉGULATEUR DE PRESSION ET UN MANOMÈTRE ÀLA SORTIE D’AIR DU
COMPRESSEUR. SUIVRE LES RECOMMANDATIONS DU FABRICANT DE
L’ÉQUIPEMENT ET NE JAMAIS EXCÉDER LA VALEUR NOMINALE DE PRESSION
SPÉCIFIÉE DES ACCESSOIRES. NE JAMAIS UTILISER LE COMPRESSEUR
POUR GONFLER DES OBJETS ÀFAIBLE PRESSION, TELS QUE LES JOUETS
D’ENFANT, LES BALLONS DE FOOTBALL OU DE BASKET-BALL, ETC.
1. LE DÉFAUT DE VIDANGER DE FAÇON APPROPRIÉE L’EAU CONDENSÉE
DANS LE RÉSERVOIR RISQUE DE CAUSER LA ROUILLE ET L’AMINCISSEMENT
DES PAROIS EN ACIER DU RÉSERVOIR.
2. DES MODIFICATIONS OU TENTATIVES DE RÉPARATION FAITES SUR LE
RÉSERVOIR.
3. DES MODIFICATIONS NON AUTORISÉES APPORTÉES ÀLA SOUPAPE DE
DÉCHARGE, ÀLA SOUPAPE DE SÛRETÉOU ÀTOUTE AUTRE COMPOSANTE
QUI CONTRÔLE LA PRESSION DU RÉSERVOIR.
4. DES VIBRATIONS EXCESSIVES PEUVENT AFFAIBLIR LE RÉSERVOIR ET
CAUSER UNE RUPTURE OU UNE EXPLOSION. DES VIBRATIONS
EXCESSIVES SERONT PRODUITES SI LE COMPRESSEUR N’EST PAS FIXÉ
DE FAÇON APPROPRIÉE.
FIXATIONS ET ACCESSOIRES :
LE FAIT D’EXCÉDER LA PRESSION NOMINALE DES OUTILS
PNEUMATIQUES, PISTOLETS PULVÉRISATEURS, ACCESSOIRES
PNEUMATIQUES, PNEUS ET AUTRES OBJETS GONFLABLES RISQUE DE
PROVOQUER L’EXPLOSION DE CES DERNIERS ET LA PROJECTION DE
PIÈCES, CE QUI RISQUE DE CAUSER DE GRAVES BLESSURES.
RISQUE PRÉVENTION
RISQUE PRÉVENTION
CONSERVER CES DIRECTIVES
DANGER
MESURES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
UN EMPLOI OU UN ENTRETIEN NON APPROPRIÉS DE CE PRODUIT PEUT CAUSER DES BLESSURES GRAVES ET DES DOMMAGES À
LA PROPRIÉTÉ. LIRE ATTENTIVEMENT TOUS LES AVERTISSEMENTS ET LES DIRECTIVES D’UTILISATION AVANT D’UTILISER CET
APPAREIL.

D20414 Rev. 0 2/15/00 4-FR
RISQUE PRÉVENTION
RISQUE DE PROJECTION D’OBJETS
LE JET D’AIR COMPRIMÉPEUT CAUSER DES LÉSIONS AUX TISSUS DE LA
PEAU EXPOSÉE ET PEUT PROJETER DE LA SALETÉ, DES COPEAUX, DES
PARTICULES LIBRES ET DE PETITS OBJETS ÀHAUTE VITESSE, CE QUI
RISQUE DE CAUSER DES DOMMAGES ÀLA PROPRIÉTÉOU DES BLESSURES.
PORTER TOUJOURS DES LUNETTES DE PROTECTION HOMOLOGUÉES
ANSI Z87.1 AVEC DES ÉCRANS LATÉRAUX LORS DE L’UTILISATION DU
COMPRESSEUR.
NE JAMAIS DIRIGER LA BUSE OU LE PULVÉRISATEUR VERS SOI, VERS
D’AUTRES PERSONNES OU VERS DES ANIMAUX.
TOUJOURS METTRE LE COMPRESSEUR HORS FONCTION ET PURGER LA
PRESSION DU BOYAU D’AIR ET DU RÉSERVOIR AVANT D’ENTAMER
L’ENTRETIEN OU D’ATTACHER DES OUTILS OU ACCESSOIRES.
L’AIR COMPRIMÉDE VOTRE COMPRESSEUR D’AIR N’EST PAS SÉCURITAIRE
POUR L’INHALATION. LE JET D’AIR PEUT CONTENIR DU MONOXYDE DE
CARBONE, DES VAPEURS TOXIQUES OU DES PARTICULES SOLIDES DU
RÉSERVOIR.
LES MATIÈRES VAPORISÉES TELLES QUE LA PEINTURE, LES SOLVANTS DE
PEINTURE, LES DÉCAPANTS, LES INSECTICIDES ET LES HERBICIDES
CONTIENNENT DES VAPEURS NOCIVES ET TOXIQUES.
TOUJOURS UTILISER LE COMPRESSEUR D’AIR ÀL’EXTÉRIEUR, DANS UN
ENDROIT PROPRE ET BIEN AÉRÉ.ÉVITER DES ENDROITS CLOS TELS QUE
GARAGES, SOUS-SOLS ET HANGARS D’ENTREPOSAGE QUI NE SONT PAS
DOTÉS DE SYSTÈMES D’ÉCHANGE D’AIR. GARDER LES ENFANTS, LES
ANIMAUX DOMESTIQUES ET AUTRES, LOIN DE LA ZONE DE TRAVAIL.
NE JAMAIS INHALER L’AIR ÉMIS PAR LE COMPRESSEUR, QUE CE SOIT
DIRECTEMENT OU AU MOYEN D’UN DISPOSITIF RESPIRATEUR BRANCHÉAU
COMPRESSEUR.
TRAVAILLER DANS UN ENDROIT OÙIL Y A UNE BONNE VENTILATION
TRANSVERSALE. BIEN LIRE ET RESPECTER LES DIRECTIVES DE SÉCURITÉ
INDIQUÉES SUR L’ÉTIQUETTE OU LA FICHE SIGNALÉTIQUE DE LA MATIÈRE
QUI EST VAPORISÉE. PORTER UN RESPIRATEUR HOMOLOGUÉPAR LE
NIOSH/MSHA ET CONÇU POUR L’APPLICATION EN QUESTION.
DANGER
RISQUE PRÉVENTION
RISQUE PAR INHALATION
VOTRE COMPRESSEUR D’AIR EST ALIMENTÉPAR ÉLECTRICITÉ. COMME
AVEC TOUS LES APPAREILS ÉLECTRIQUES, SI L’APPAREIL N’EST PAS
UTILISÉDE FAÇON APPROPRIÉE, IL PEUT CAUSER DES CHOCS
ÉLECTRIQUES.
TOUTE RÉPARATION EFFECTUÉE PAR UNE PERSONNE NON QUALIFIÉE
PEUT ENTRAÎNER DES BLESSURES GRAVES OU LA MORT PAR
ÉLECTROCUTION.
MISE ÀLA TERRE : LE DÉFAUT D’ÉTABLIR UNE MISE ÀLA TERRE
APPROPRIÉE POUR CET APPAREIL PEUT ENTRAÎNER DES BLESSURES
GRAVES OU LA MORT PAR ÉLECTROCUTION. VOIR LES DIRECTIVES DE
MISE ÀLA TERRE.
NE JAMAIS FAIRE FONCTIONNER LE COMPRESSEUR ÀL’EXTÉRIEUR
LORSQU’IL PLEUT OU DANS DES CONDITIONS HUMIDES.
NE JAMAIS FAIRE FONCTIONNER LE COMPRESSEUR SANS LES
COUVERCLES OU LORSQUE CEUX-CI SONT ENDOMMAGÉS.
TOUT CÂBLAGE ÉLECTRIQUE OU TOUTE RÉPARATION REQUIS SUR CET
APPAREIL DEVRAIT ÊTRE EFFECTUÉPAR LE PERSONNEL D’UN CENTRE
DE SERVICE APRÈS-VENTE AUTORISÉ, CONFORMÉMENT AUX CODES
ÉLECTRIQUES NATIONAUX ET LOCAUX.
S’ASSURER QUE LE CIRCUIT ÉLECTRIQUE ALIMENTANT LE COMPRESSEUR
FOURNIT UNE MISE ÀLA TERRE ÉLECTRIQUE APPROPRIÉE, UNE TENSION
APPROPRIÉE ET UNE PROTECTION ADÉQUATE PAR FUSIBLES.
RISQUE PRÉVENTION
RISQUE DE CHOC ÉLECTRIQUE

D20414 Rev. 0 2/15/00
5-FR
LES PIÈCES MOBILES TELLES QUE LA POULIE, LE VOLANT-MOTEUR ET LA
COURROIE PEUVENT ENTRAÎNER DES BLESSURES GRAVES SI ELLES
ENTRENT EN CONTACT AVEC UNE PARTIE DU CORPS OU DES
VÊTEMENTS.
EN TENTANT DE FAIRE FONCTIONNER LE COMPRESSEUR AVEC DES
PIÈCES MANQUANTES OU ENDOMMAGÉES, OU DE RÉPARER LE
COMPRESSEUR SANS LES GARDES DE PROTECTION, ON S’EXPOSE
AUX PIÈCES MOBILES, CE QUI PEUT ENTRAÎNER DES BLESSURES
GRAVES.
NE JAMAIS FAIRE FONCTIONNER LE COMPRESSEUR SANS LES
GARDES OU LES COUVERCLES OU LORSQUE CEUX-CI SONT
ENDOMMAGÉS.
TOUTE RÉPARATION REQUISE SUR CET APPAREIL DEVRAIT ÊTRE
EFFECTUÉE PAR LE PERSONNEL D’UN CENTRE DE SERVICE APRÈS-
VENTE AUTORISÉ.
DANGER
RISQUE RELIÉ AUX PIÈCES MOBILES
RISQUE PRÉVENTION
LE FAIT DE TOUCHER AUX SURFACES DE MÉTAL EXPOSÉES TELLES
QUE LA TÊTE DU COMPRESSEUR OU LES TUBES DE SORTIE PEUT
CAUSER DE GRAVES BRÛLURES ÀLA PEAU.
LA TÊTE DU COMPRESSEUR ET LES TUBES DEVIENNENT TRÈS CHAUDS
LORS DU FONCTIONNEMENT.
NE JAMAIS TOUCHER AUX PIÈCES DE MÉTAL EXPOSÉES DU MOTEUR
OU DU COMPRESSEUR DURANT OU IMMÉDIATEMENT APRÈS LE
FONCTIONNEMENT. LE MOTEUR ET LE COMPRESSEUR DEMEURENT
CHAUDS PENDANT PLUSIEURS MINUTES APRÈS LEUR
FONCTIONNEMENT.
NE PAS TENTER D’ATTEINDRE LES COMPOSANTES DERRIÈRE LES
GARDES DE PROTECTION ET NE PAS EFFECTUER DE L’ENTRETIEN AVANT
D’AVOIR LAISSÉREFROIDIR L’APPAREIL.
RISQUE PRÉVENTION
UN COMPRESSEUR PORTATIF PEUT TOMBER D’UNE TABLE, D’UN ÉTABLI
OU D’UN TOIT. L’IMPACT PEUT CAUSER DES DOMMAGES AU
COMPRESSEUR ET DES BLESSURES CORPORELLES OU LA MORT DE
L’UTILISATEUR.
TOUJOURS S’ASSURER DE LA STABILITÉDU COMPRESSEUR AVANT DE
LE FAIRE FONCTIONNER AFIN DE PRÉVENIR TOUT MOUVEMENT
ACCIDENTEL DE L’APPAREIL. NE JAMAIS UTILISER UN COMPRESSEUR
SUR UN TOIT OU DANS UNE POSITION ÉLEVÉE ; UTILISER PLUTÔT UN
BOYAU D’AIR SUPPLÉMENTAIRE POUR ATTEINDRE LES ENDROITS
ÉLEVÉS.
RISQUE PRÉVENTION
RISQUE DE BRÛLURES
ESW-99 —9/26/99
RISQUE DE CHUTE
DES FUITES OU DES DÉVERSEMENTS D’HUILE PEUVENT SE
PRODUIRE ET ENTRAÎNER DES RISQUES D’INCENDIE, OU DES
PROBLÈMES AUX VOIES RESPIRATOIRES, DES BLESSURES GRAVES
OU LA MORT. DES FUITES D’HUILE ENDOMMAGENT LES TAPIS, LA
PEINTURE ET TOUTE AUTRE SURFACE DES VÉHICULES OU DES
REMORQUES.
RISQUE PRÉVENTION
TOUJOURS PLACER LE COMPRESSEUR SUR UN TAPIS DE
PROTECTION POUR ÉVITER L’ENDOMMAGEMENT DU VÉHICULE PAR
DES FUITES. RETIRER LE COMPRESSEUR DU VÉHICULE
IMMÉDIATEMENT ÀL’ARRIVÉE.
RISQUE DE DOMMAGES À LA PROPRIÉTÉ PENDANT LE
TRANSPORT DU COMPRESSEUR
(incendie, inhalation, dommages aux surfaces du véhicule)

D20414 Rev. 0 2/15/00 6-FR
RENSEIGNEMENTS GÉNÉRAUX
LEXIQUE
TABLEAU DES SPÉCIFICATIONS
Modèle no : 919.727121
Alésage 1 7/8 po (4,76 cm)
Course du cylindre 1 1/4 po (3,175 cm)
Tension –phase unique 120
Exigence minimale du circuit de dérivation 10 a
Genre de fusible àretardement àélément double
Capacitédu réservoir d’air 12 gal. (É.-U.) (45,4 L)
Pression d’enclenchement approx. 100
Pression de coupe-circuit approx. 125
Pi3/min standard (SCFM) à40 psi (lb/po. ca.) 3,7
Pi3/min standard (SCFM) à90 psi (lb/po. ca.) 2,6
Vous avez fait l’achat d’un compresseur d’air de 1 cylindre
muni d’une pompe de compresseur d’air àphase unique et
d’un réservoir d’air. Cet appareil comprend aussi des
roues, un régulateur et des manomètres.
Ce compresseur d’air ne requiert aucune huile. Vous
pouvez donc maintenant profiter de tous les avantages
qu’offre un compresseur d’air sans jamais devoir faire
l’achat, l’ajout ou un changement d’huile.
Votre compresseur d’air peut être utiliséavec des pistolets à
peindre, des outils pneumatiques, des pistolets àcalfeutrer,
des cloueuses/agrafeuses, des pinceaux vaporisateurs, ainsi
que des trousses pour le gonflage. Un régulateur de pression
d’air est requis pour la plupart de ces applications.
Un filtre àair en ligne qui élimine l’humiditéet la saletéde
l’air comprimédevrait être utilisélorsque applicable.
Un régulateur en ligne peut être utilisési un réglage plus
précis en aval est nécessaire.
CFM : pieds cubes par minute.
SCFM : pieds cubes par minute standard. Une unitéde
mesure de sortie d’air.
PSIG : (jauge) livres par pouce carré. Une unitéde mesure
de tension (pression).
ASME : American Society of Mechanical Engineers.
Fabriqué, mis àl’essai, inspectéet enregistrépour
répondre aux normes de la ASME.
Pression d’enclenchement : Lorsque le moteur est en
arrêt, la pression du réservoir d’air s’abaisse tandis que
vous continuez d’utiliser votre accessoire. Quand la
pression du réservoir baisse àun certain taux de pression
et que le manostat est en mode automatique (AUTO), le
moteur se remet automatiquement en marche. La basse
pression àlaquelle le moteur se remet automatiquement
en marche s’appelle la “pression d’enclenchement”.
Pression coupe-circuit : Lorsque vous mettez votre
compresseur d’air en marche et qu’il commence à
fonctionner, la pression d’air dans le réservoir commence à
s’accumuler. La pression monte et atteint un taux assez
élevéavant que le moteur ne s’arrête automatiquement
protégeant ainsi le réservoir d’air d’un taux de pression qui
excèderait sa capacité. La haute pression àlaquelle le
moteur s’arrête s’appelle la “pression de coupe-circuit”.
CSA : Les produits électriques vendus au Canada doivent
être certifiés selon les normes applicables de l’ACNOR.
L’Association canadienne de normalisation (ACNOR) est un
organisme qui établit les normes et effectue les essais pour
vérifier l’aspect sécuritaire des produits. Les produits qui
sont homologués CSA ont fait l’objet d’une évaluation et
d’essais et ont étéjugés conformes aux normes, ou
excédant les normes, de sécuritéet de rendement
électrique.