Craftsman 358.794741 User manual

Operator's Manual
I [RAFTSMAN"I
25cc/1.5 cU.in. 2-Cycle
200 MPH/430 CFM
GASOLINE POWERED
BLOWERNAC
Model No.
358.794741
• Safety
• Assembly
• Operation
• Maintenance
• Parts List
A
?
•
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product:
Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.
1-800-235-5878 (Hours listed are Central Time)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
545154792 Rev. 3 1/3/08 BRW

TABLE OF CONTENTS
Warranty Statement
Identification
of Safety Symbols
Safety Rules
2
2
3
5
8
11
Storage
Troubleshooting Table
Emissions Statement
Parts List
13
14
15
17
20
Assembly
Operation Spanish
Maintenance Parts and Ordering Back Cover
WARRANTY STATEMENT
TWO YEAR FULL WARRANTY ON CRAFTSMAN® GAS BLOWER
When used and maintained according to the operator's manual, if this productfails
due to a defect
in material orworkmanship within two (2) years from the date of pur-
chase, return it to any Sears store, Sears Service Center, or other Craftsman outlet
in the United States for free repair (or replacernent if repair proves impossible).
This warranty excludes spark plug and air cleaner, which are expendable parts that
can wear out from normal use
in less than two years.
This warranty applies for only 30 days from the date of purchase if this product is
used for commercial or rental purposes.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
IDENTIFICATION OF SAFETY SYMBOLS
i L'i. i AWARNING, m, ,,'~, b,.'",ew",'Ceml'"" "'
__ Improper use can cause serious Injury.
i ft i R,.d y'", "P''"''(' m,,".1 ",,,ful, ",,;, yeo oomp'o>"y ".
derstand and can follow all warnings and safety rules before
operating the unit. Failure to do so can result
in serious injury.
Save operator's manual.
••
The blower can throw objects
C'" violently. You can be blinded or
~
'\' ,~, 0 injured. Always wear hearing
"'~X,,',} '," . . protection and safety glasses
'~~:,;~>;-, Z87 marked Z87. Always wear
-
',' . heavy, long pants, long sleeves,
~===::;::=::;;:====I--':::!!!=---' boots and gloves.
Hazard zone for thrown objects. Keep children,
bystanders, and animals away from work area a
minimum of 30 feet (10 meters) when starting or
operating unit.
Do not point blower nozzle in the
direction of people or pets.
- 2 -

IDENTIFICATION OF SAFETY SYMBOLS
I@',
-:It>@) 1Secure hair above shoulder length,
:'!I Do not wear jewelry, loose clothing,
or clothing with loosing hanging
~, straps, ties, tassels, etc, They can
" , be caught in moving parts,
~========~~==~
1
.1 - ~ 1 Alwey, ,<op """""d d'",",,,, 'p"" pl'g
• • 1\ ft ,before cleaning or servicing,
4)
A WARNING: Stop the engine before opening the vacuum inlet door. The
engine must be stopped and the impeller blades no longer turning
to avoid serious
injury from the rotating blades, Gently tilt the handle ofthe screwdriver toward the
back of the unit to release the latch while pulling
up on the vacuum inlet cover with
your other hand,
I ~ IWhCO "",g .",,""m """hmo"" ~c ""'" d".ood<o
pick up dry material such as leaves, grass, small twigs, and bits
of paper.
Do not vacuum stones, gravel, metal, broken glass,
?, Sj'" etc" to avoid severe damage to the impeller,
[®]
A WARNING: Fire hazard, Never mix, pour, or store gasoline
~" or use the unit near a flame or sparks (including smoking, open
:. "'" flames, or work that can cause sparks),
1 J 1.11. WARNING, The m"ffI" " '"" hoi dw',g eod "'10' "'0
Do not touch the muffler, muffler guard, or surrounding surfaces,
d*W or allow combustible material such as dry grass or fuel to do so,
SAFETY RULES
AWARNING: Failure to follow all
Safety Rules and Precautions can re-
sult
in serious injury,
KNOW YOUR UNIT
• Read your instruction manual care-
fully until you completely understand
and can follow all warnings and
safety rules before operating the
unit
• Restrict unit to users who under-
stand and will follow all warnings and
safety rules
in this manual.
AWARNING: Inspect area before
starting
unit Remove all debris and
hard objects such as rocks, glass,
wire, etc, that can ricochet, be thrown,
or otherwise cause injury or damage
during operation,
- 3 -

Use your unit as a blower for:
• Sweeping debris or grass clippings
from driveways, sidewalks, patios, etc,
• Blowing grass clippings, straw, or
leaves into piles, around joints, or be-
tween bricks,
Use your unit as a vacuum for:
• Picking up dry material such as
leaves, grass, small twigs, and bits of
paper
• For best results during vacuum use,
operate your unit at high speed,
• Move slowly back and forth over the
material as you vacuum, Avoid forc-
ing the unit into a pile of debris as
this can clog the
unit
• Keep the vacuum tube about an inch
above the ground for best results,
PLAN AHEAD
• Always wear eye protection when op-
erating, servicing, or pertorming main-
tenance
on unit Wearing eye protec-
tion
will help to prevent rocks or debris
from being blown or ricocheting into
eyes and face which can result in
blindness and/or serious injury, Eye
protection should
be marked Z87,
• Always wear foot protection, Do not
go barefoot or wear sandals,
• Always wear respirator or face mask
when working with unit
in dusty envi-
ronments,
• Secure hair above shoulder length,
Secure or remove jewelry, loose
clothing, or clothing with loosely
hanging straps, ties, tassels, etc,
They can be caught
in moving parts,
• Do not operate unit when you are
tired, ill, upset, or if you are under the
influence of alcohol, drugs, or medi-
cation,
• Keep children, bystanders, and ani-
mals away from work area a mini-
mum of 30 feet (10 meters) when
starting or operating
unit Do not
point blower nozzle
in the direction of
people or pets,
HANDLE FUEL WITH CAUTION, IT
IS
HIGHLY FLAMMABLE
• Eliminate all sources of sparks or
flame (including smoking, open
flames, or work that can cause
sparks)
in the areas where fuel is
mixed, poured, or stored,
• Mix and pour fuel in an outdoor area;
store fuel
in a cool, dry, well ventilated
place; use
an approved, marked con-
tainer for
all fuel purposes,
• Do not smoke while handling fuel or
while operating the
unit
• Make sure the unit is properly as-
sembled and in good operating con-
dition,
• Do not fill fuel tank while engine is
running,
• Avoid spilling fuel or oil, Wipe up fuel
spills before starting engine,
• Move at least 10 feet (3 meters)
away from fuel and fueling site be-
fore starting engine,
• Always store gasoline in a container
approved for flammable liquids,
OPERATE YOUR UNIT SAFELY
AWARNING: Stop the engine be-
fore opening the vacuum inlet
door. The
engine must
be stopped and the impel-
ler blades no longer turning
to avoid se-
rious injury from the rotating blades,
• Inspect unit before each use for
worn, loose, missing, or damaged
parts,
Do not use until unit is in
proper working order,
• Keep outside surtaces free from oil
and fuel,
• Never start or run engine inside a
closed room, building or other un-
ventilated area, Breathing exhaust
fumes can kill,
•
To avoid static electricity shock, do
not wear rubber gloves or any other
insulated gloves while operating unit
• Do not set unit on any surface except
a clean, hard area while engine
is run-
ning, Debris such as gravel, sand,
dust, grass, etc, could be picked
up by
the air intake and thrown out through
discharge opening, damaging
unit,
property, or causing serious injury to
bystanders or operato!'
• Avoid dangerous environments, Do
not use
in unventilated areas or
where explosive vapors or carbon
monoxide build up could be
present
• Do not overreach or use from unsta-
ble surtaces such as ladders, trees,
steep slopes, rooftops, etc, Keep firm
footing and balance at all times,
• Never place objects inside the
blower tubes; always direct the blow-
ing debris away from people, ani-
mals, glass, and solid objects such
as trees, automobiles, walls, etc, The
force of air can cause rocks, dirt, or
sticks to be thrown or to ricochet
which can hurt people or animals,
break glass, or cause other damage,
• Never run unit without the proper
equipment attached, When using
your unit as a blower, always install
- 4 -

blower tubes. When using the op-
tional vacuum kit, always install vac-
uum tubes and vacuum bag assem-
bly. Make sure vacuum bag assem-
bly is completely zipped.
• Check air intake opening, blower
tubes, and vacuum tubes frequently,
always with engine stopped and
spark plug disconnected. Keep vents
and discharge tubes free of debris
which can accumulate and restrict
proper air flow.
• Never place any object
in air intake
opening
as this could restrict proper air
ftow and cause damage
to the unit
• Never use for spreading chemicals,
fertilizers, or other substances which
may contain toxic materials.
•
To avoid spreading fire, do not use
near leaf or brush fires, fireplaces,
barbecue pits, ashtrays, etc.
• Use only for jobs explained in this
manual,
MAINTAIN YOUR UNIT PROPERLY
AWARNING: Disconnect spark
plug before performing maintenance
except for carburetor adjustments.
• Have all maintenance other than the
recommended procedures described
in the instruction manual performed
by a Sears Service Center.
• Use only recommended Craftsman
replacement parts; use of any other
parts may void your warranty and
cause damage to your
unit
• Empty fuel tank before storing the
unit Use up fuel left in carburetor by
starting engine and letting it run until
it stops.
• Do not use any accessory or attach-
ment other than those recommended
by manufacturer for use with your unit
• Do not store the unit or fuel in a closed
area where fuel vapors can reach
sparks or
an open flame from hot
water heaters, electric motors or
switches, furnaces,
etc.
• Store in a dry area out of reach of
children.
SAFETY NOTICE: Exposure
to vibra-
tions through prolonged use of gasoline
powered hand tools could cause blood
vessel or nerve damage
in the fingers,
hands, and joints of people prone to cir-
cuation disorders or abnormal swelling.
Prolonged use
in cold weather has been
linked to blood vessel damage in other-
wise healthy people. If symptorns occur
such as numbness, pain, loss of
strength, change
in skin color or texture,
or loss of feeling
in the fingers, hands, or
joints, discontinue the use of this tool
and seek rnedical attention. An
antivibration system does not guarantee
the avoidance of these problerns. Users
who operate power tools
on a continual
and regular basis must monitor closely
their physical condition and the condition
of this tool,
SPECIAL NOTICE: This unit
is
equipped with a temperature limiting
muffler and spark arresting screen
which meets the requirements
of Cali-
fornia Codes 4442 and 4443. All U.S.
forest land and the states
of California,
Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington require by
law that many internal cornbustion en-
gines be equipped with a spark arrest-
ing screen. If you operate
in a locale
where such regulations exist, you are
legally responsible for rnaintaining the
operating condition
of these parts. Fail-
ure to do so is a violation of the law.
Refer to the MAINTENANCE section for
information on maintenance of the
muffler and spark arresting screen.
ASSEMBLY
CARTON CONTENTS
Check carton contents against the fol-
lowing
list
Model 358.794741
• Blower
• Upper blower tube
• Lower blower tube
• High velocity nozzle
• Elbow tube
• Vacuum bag
• Upper vacuum tube
• Lower vacuum tube
• 2-Cycle engine oil
NOTE: It is norrnal for the fuel filter to
rattle in the empty fuel tank.
ASSEMBLY
AWARNING: Stop engine and be
sure the impeller blades have stopped
turning before opening the vacuum in-
let door or attempting to insert or re-
move the vacuurn tubes. The rotating
blades can cause serious injury.
- 5 -

AWARNING: If you receive your
unit assembled, repeat all steps to en-
sure your unit is properly assembled
and all fasteners are secure,
A standard screwdriver is required
for assembly,
BLOWER ASSEMBLY
BLOWER TUBE ASSEMBLY
If you have already assembled your
unit for use as a vacuum, remove the
vacuum tubes and collection bag,
1, Align the rib on the upper blower
tube with the groove in the blower
outlet; slide the tube into place,
NOTE: Knob must be loose enough to
allow blower tube to be inserted in blow-
er outlet Loosen knob by turning coun-
terclockwise,
2, Secure the tube by turning the
knob clockwise,
3, Align the slots on the lower blower
tube with the tabs on the upper
blower tube,
Lower Blower
Tube
4, Slide the lower blower tube onto
the upper blower tube,
5, Turn the lower blower tube clock-
wise until a click is felt to secure
the lower blower tube to the upper
blower tube,
NOTE: When the upper and lower
blowertubes are assembled together
properly, the arrows on both tubes will
be aligned,
6. To remove the tubes, turn the knob
counterclockwise to loosen the
tubes; remove the tubes.
HIGH-SPEED NOZZLE ASSEMBLY
When greater air speed is desired, use
the
high-speed nozzle.
1. Align the slots on the nozzle with
the tabs on the lower blower tube,
C--~rr.'~
~-'~~-~~
/"
Lower Blower
Tube
High-Speed
Nozzle
--\'- t
7~~€2~
Tab Slot
2, Slide the nozzle onto the lower
blower tube,
3, Turn the nozzle clockwise until a
click is felt to secure the nozzle to
the lower blower tube,
VACUUM ASSEMBLY
VACUUM BAG ASSEMBLY
1, Open the zipper on the vacuum
bag and insert the elbow tube,
2, Push the small end of the elbow
tube through the small opening in
the bag,
~i~'::'
Zipper /
Opening Small Opening
NOTE: Make sure edge of the small
opening is flush against the flared area
of the elbow tube, and the
rib on the
elbow tube is on the bottom,
3, Close the zipper on the bag, Make
sure the zipper
is closed completely,
4, Remove blower tubes from engine,
te,;,
5, I I i' i the blow-
er outlet Make sure elbow tube rib
is aligned with the blower outlet
groove,
- 6 -

6. Turn knob clockwise to secure el-
bow tube.
VACUUM TUBE ASSEMBLY
AWARNING: Stop engine and be
sure the impeller blades have stopped
turning before opening the vacuum inlet
door or attempting to insert or remove
the vacuum or blower tubes. The rotat-
ing blades can cause serious injury
1. Insert the tip of a screwdriver into
the latch area of the vacuum
inlet
Vacuum Inlet Cover
2. Gently tilt the handle of the screw-
driver toward the front
of the unit to
release the latch while pulling up
on the vacuurn inlet cover with your
other hand.
3. Hold the vacuum inlet cover open
until upper vacuurn tube is
installed.
Vacuum Inlet
Vacuum
Inlet
4. Align the tabs on the inside of the
vacuum inlet with the slots
in the
upper vacuum tube.
5. Push the upper vacuum tube into
the vacuum inlet Turn the tube
counterclockwise until a click
is felt
to secure the tube to the blower unit
6. Align slanted end of lower vacuum
tube as shown. Firmly push lower
vacuurn tube into upper vacuum
tube.
lower vacuum tube
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Remove the elbow tube and vacu-
um bag by turning the knob coun-
terclockwise to loosen the elbow
tube.
2. Remove the vacuum tubes by turn-
ing the tubes clockwise.
3. Close the vacuum inlet cover and
make sure it is latched closed.
4. Reinstall the blower tubes (see
BLOWER TUBE ASSEMBLY).
VACUUM BAG SHOULDER STRAP
ADJUSTMENT
1. Hold the unit as shown with the muf-
fler side facing away from your body
and clothes.
2. Pass the shoulder strap over your
head and onto your right shoulder.
3. Extend your left arm toward the
rear
of the vacuum bag.
4. Adjust shoulder strap until the
vacuurn bag/shoulder strap seam
lies between your thurnb and index
finger.
5. Make sure air flows freely from the
elbow tube into bag. If bag
is
kinked, the unit will not operate
properly.
- 7 -

SHOULDER STRAP ATTACHMENT
(optional accessory #71-85783)
1. Pass the shoulder strap over your
head and onto your left shoulder.
2. Snap the hook onto the retainer
(see following illustration).
BLOWER USE VACUUM USE
OPERATION
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFE1Y RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the location
of the various controls and adjustments. Save this manual for future reference.
~~~~~~;':vacuum Handle
STOP SWITCH
The STOP switch is used to stop the
engine.
To stop the engine. push and
hold the
STOP switch in the STOP posi-
tion until the engine stops.
THROTTLE TRIGGER
The THROTTLE TRIGGER is used to se-
lect the desired engine speed.
PRIMER BULB
The PRIMER BULB removes air from
the carburetor and fuel lines and fills
them with fuel. This allows you to start
the engine with fewer pulls on the
starter rope. Activate primer bulb by
pressing it and allowing
it to return to
its original position.
CHOKE LEVER
The CHOKE helps to supply fuel to the
engine to aid
in cold starting. Activate
the choke by moving the choke lever
to
the FULL CHOKE position. After engine
attempts
to start. move the choke lever
to the HALF CHOKE position. Once en-
gine starts, move choke lever
to the
RUN position.
- 8 -

OPERATING TIPS
• While vacuuming or blowing debris,
hold the unit with the muffler side fac-
ing away from your body and clothes
(see OPERATING POSITION below),
•
To reduce the risk of hearing loss
associated with sound level(s), hear-
ing protection
is required,
• To reduce the risk of injury associated
with contacting rotating parts, stop the
engine before installing or removing
attachments. Do not operate without
guard(s)
in place.
• Operate power equipment only at rea-
sonable hours-not early in the morn-
ing or late at night when people might
be disturbed. Comply with times listed
in local ordinances. Usual recommen-
dations are 9:00
a.m. to 5:00 p.m.,
Monday though Saturday.
•
To reduce noise levels, limit the num-
ber
of pieces of equipment used at
anyone time.
• To reduce noise levels, operate pow-
er blowers at the lowest possible
throttle speed to do the job.
• Use rakes and brooms to loosen
debris before blowing.
•
In dusty conditions, slightly dampen
surfaces or use a mister attachment
when water is available.
• Conserve water by using power blow-
ers instead of hoses for many lawn
and garden applications, including
areas such
as gutters, screens, patios,
grills, porches, and gardens.
• Watch out for children, pets, open
windows, or freshly washed cars.
Blow debris away safely.
• Use the full blower nozzle extension
so the air stream can work close to
the ground.
• After using blowers and other equip-
ment,
CLEAN UP! Dispose of debris
in trash receptacles.
OPERATING POSITION
BEFORE STARTING ENGINE
AWARNING: Be sure to read the
fuel information
in the safety rules
before you begin. If you do not
understand the safety rules,
do not
attempt to fuel your unit. Call
1-800-235-5878.
FUELING ENGINE
AWARNING: Remove fuel cap
slowly when refueling.
This engine
is certified to operate on un-
leaded gasoline. Before operation, gaso-
line must be mixed with a good quality
synthetic 2-cycle air-cooled engine
oil.
We recommend Craftsman brand syn-
thetic
oil. Mix gasoline and oil at a ratio
of 40:1. A
40:1 ratio is obtained by mix-
ing 3.2 ounces of oil with 1 gallon of un-
leaded gasoline. Included with this blow-
er
is a 3.2 ounce container of oil. Pour
the entire contents of this container into
1 gallon of gasoline
to achieve the prop-
er fuel mixture.
DO NOT USE automotive
oil or boat oil. These oils will cause en-
gine damage. When mixing fuel, follow
instructions printed on container. Once
oil is added to gasoline, shake container
momentarily to assure that the fuel
is
thoroughly mixed. Always read and fol-
low the safety rules relating
to fuel be-
fore fueling your unit.
IMPORTANT
Experience indicates that alcohol
blended fuels (called gasohol
or using
ethanol or methanol) can attract mois-
ture which leads to separation and
formation of acids during storage.
Acidic gas can damage the fuel sys-
tem of an engine while
in storage.
- 9 -

To avoid engine problems, empty the
fuel system before storage for 30 days
or longer, Drain the gas tank, start the
engine and let
it run until the fuel lines
and carburetor are empty, Use fresh
fuel next season, Never use engine or
carburetor cleaner products
in the fuel
tank or permanent damage may occur.
Fuel stabilizer is an acceptable alter-
native in minimizing the formation of
fuel gum deposits during storage,
Craftsman brand oil
is already blended
with fuel stabilizer, See the STORAGE
section for additional information,
HOW TO STOP YOUR ENGINE
• Release the throttle trigger.
• Push and hold the
STOP switch in
the STOP position until the engine
stops,
HOW TO START YOUR ENGINE
AWARNING: You MUST make sure
the tubes are secure before using the
unit
• Fuel engine, Move at least 10 feet (3
meters) away from the fueling site,
• Hold the unit in the starting position
as shown, Make sure the blower end
is directed away from people, ani-
mals, glass, and solid objects,
STARTING POSITION
AWARNING: When starting engine,
hold the unit as illustrated, Do not set
unit on any sutface except a clean, hard
area when starting engine or while en-
gine
is running, Debris such as gravel,
sand, dust, grass, etc, could be picked
up by the air intake and thrown out
through the discharge opening, damag-
ing the unit or property, or causing seri-
ous injury
to bystanders or the operator,
STARTING A COLD ENGINE (or
warm engine after running out of fuel)
1, Slowly press the primer bulb 6 times,
2, Move choke lever to the FULL
CHOKE position,
3, Squeeze the throttle trigger fully and
hold through all remaining steps,
4, This unit has the Sim-pul-< starting
system,
You do not have to pull the
starter rope handle sharply or briskly,
Pull starter rope handle with a con-
trolled and steady motion until en-
gine sounds as if
it is trying to start,
but do not pull rope more than 6
times,
5, As soon as engine sounds as if it is
trying to start, move choke lever to
HALF CHOKE position,
6, Pull starter rope until engine runs,
but no more than 6 pulls, NOTE: If
the engine doesn't start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the
primer bulb 6 times, Squeeze and
hold the throttle trigger and pull the
starter rope 2 more times, Move
the choke lever to the HALF CHOKE
position and pull the starter rope
until the engine runs, but no more
than 6 pulls, Ifthe engine still
doesn't start, it is probably flooded,
Proceed to STARTING A FLOODED
ENGINE,
7, Once the engine starts, allow it to
run 10 seconds, then move the
choke lever
to the RUN position, Al-
low the unit to
run for 30 more se-
conds at
RUN before releasing the
throttle trigger. NOTE: If engine dies
with the choke lever
in the RUN
position, move the choke lever to
the HALF CHOKE position and pull
the rope until engine runs, but no
more than 6 pulls,
STARTING A WARM ENGINE
1, Move the choke lever to the HALF
CHOKE position,
- 10 -

2. Squeeze the throttle trigger fully and
hold through all remaining steps.
3. Pull starter rope with a controlled
and steady motion until engine
runs, but
no more than 6 pulls.
4. Allow engine to run 15 seconds,
then move the choke lever
to RUN.
NOTE: If engine has not started, pull
starter rope 5 more pulls. If engine still
does not run,
it is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by plac-
ing the choke lever
in the RUN position;
then, pull the rope to clear the engine of
excess fuel. This could require pulling
the starter handle many times depend-
ing
on how badly the unit is ftooded. If
the unit still doesn't start, refer to
TROUBLESHOOTING TABLE or call
1-800-235-5878.
MAINTENANCE
CUSTOMER RESPONSIBILITIES
AWARNING: Disconnect the spark plug before performing maintenance,
service or adjustments
CARE & MAINTENANCE TASK
Check for loose fasteners and parts
Check for damaged or worn parts
Inspect and clean unit and labels
Clean air filter
Replace spark plug
Replace fuel filter
Check muffler mounting screws
AWARNING: Avoid touching muf-
fler unless engine and muffler are cold.
A hot muffler can cause serious burns.
AWARNING: Stop engine and be
sure the impeller blades have stopped
turning before opening the vacuum in-
let door or attempting to insert or re-
move the vacuum or blower tubes.
The rotating blades can cause serious
injury. Always disconnect the spark
plug before performing maintenance or
accessing movable parts.
GENERALRECOMMENDATIONS
The warranty on this unit does not cov-
er items that have been subjected to
operator abuse or negligence.
To re-
ceive full value from the warranty, the
operator must maintain unit as instruct-
ed
in this manual. Various adjustments
will need to be made periodically to
properly maintain your
unit
CHECK FOR LOOSE
FASTENERS AND PARTS
• Muffler
• Spark Plug Boot
• Air Filter
• Housing Screws
CHECK FOR DAMAGED OR
WORN PARTS
Contact Sears Service Center for re-
placement
of damaged or worn parts.
WHEN TO PERFORM
Before each use
Before each use
After each use
Every 5 hours of operation
Yearly
Yearly
Yearly
• Throttle Lever -Ensure throttle lever
functions properly by moving the
throttle lever to the
STOP position.
Make sure engine stops; then restart
engine and continue.
• Fuel Tank - Do not use unit if fuel tank
shows signs of damage or leaks.
• Vacuum Bag -Do not use vacuum
bag if it
is torn or damaged.
INSPECT AND CLEAN UNIT
AND LABELS
• After each use, inspect complete unit
for loose or damaged parts. Clean
the unit using a damp cloth with a
mild
detergent
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine per-
formance and increases fuel consump-
tion and harmful emissions. Always
clean after every 5 hours of operation.
Butto,~~~
Air Filter 1/
Cover
\~L(\ \
p~lr1lY
~~%,J~::~
Air Filter ~_ _
- 11 -

Cleaning the air filter:
1. Clean the cover and the area
around it to keep debris from falling
into the carburetor chamber when
the cover
is removed.
NOTE: Move choke lever to RUN posi-
tion before opening air filter
cover
2. Open air filter cover by pushing
button (see illustration). Remove
air filter
NOTE: Do not clean filter in gasoline
or other flammable solvent Doing so
can create a fire hazard or produce
harmful evaporative emissions.
3. Wash the filter in soap and water
4. Allow filter to dry.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
6. Replace parts.
REPLACE SPARK PLUG
Replace spark plug each year to ensure
the engine starts easier and runs better
Set spark plug gap
at 0.025 inch. Igni-
tion timing is fixed, nonadjustable.
1. Twist, then pull off spark plug boot
2. Remove spark plug from cylinder
and discard.
3. Replace with Champion RCJ-6Y
spark plug and tighten securely
with a 3/4 inch socket wrench.
4. Reinstall the spark plug boot
REPLACE FUEL FILTER
To replace fuel filter, drain unit by run-
ning
it dry of fuel, then remove fuel
cap/retainer assembly from tank. Pull
filter from tank and remove it from the
fuel line. Install new fuel filter on fuel
line; reinstall parts.
CHECK MUFFLER MOUNTING
SCREWS
Once each year, ensure muffler
mounting screws are secure and tight-
ened properly to prevent damage.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
AWARNING: The muffler on this
product contains chemicals known to
the State of California to cause cancer.
As the unit is used, carbon deposits
build up on the muffler and spark ar-
resting screen, and must be removed
to avoid creating a fire hazard or af-
fecting engine periormance.
Replace the spark arresting screen ev-
ery 50 hours of operation or if any
damage or breaks
in the screen are
noted.
NOTE: Do not attempt to clean the
spark arresting screen.
1. Remove 3 screws from muffler cov-
er Remove muffler cover
2. Loosen and remove 4 screws from
the muffler hood.
3. Remove the muffler hood and spark
arresting screen.
4. Install new spark arresting screen.
5. Reinstall muffler hood and 4
screws. Tighten screws securely.
6. Reinstall muffler cover and 3
screws. Tighten securely.
NOTE: If any part of the muffler is
cracked, broken or damaged, we rec-
ommend that the muffler be replaced.
- 12 -

CARBURETOR ADJUSTMENT
The carburetor has been carefully set
at the factory, Adjustments may be
necessary if you notice any
of the fol-
lowing conditions:
• Engine will not idle when the throttle is
released,
Idle Speed Adjustment
Allow engine to idle, Adjust speed until
engine runs without stalling (idle speed
too slow),
• Turn idle speed screw clockwise to
increase engine speed if engine
stalls or dies,
• Turn idle speed screw counterclock-
wise to decrease engine speed,
Air
Filter
Cover
If you require further assistance or are
unsure about performing this proce-
dure, contact your Sears SelVice Cen-
ter or call our customer assistance
help line at 1-800-235-5878,
STORAGE
AWARNING: Perform the following
steps after each use:
• Allow engine to cool, and secure the
unit before storing or transporting,
• Store unit and fuel in a well venti-
lated area where fuel vapors cannot
reach sparks or open flames from
water heaters, electric motors or
switches, furnaces, etc,
• Store unit with all guards in place,
Position unit so that any sharp object
cannot accidentally cause injury,
• Store unit and fuel well out of the
reach
of children,
SEASONAL STORAGE
Prepare unit for storage at end of sea-
son or if it will not be used for 30 days
or more,
If your unit is to be stored for a period
of time:
• Clean the entire unit before lengthy
storage,
• Store in a clean dry area,
• Lightly oil external metal surfaces,
FUEL SYSTEM
Empty the fuel system before storage for
30 days or longer. Drain the gas tank,
start the engine and let
it run until the
fuel lines and carburetor are empty, Use
fresh fuel next season, Under
FUELING
ENGINE in the OPERATION section of this
manual, see message labeled
IMPORTANT regarding the use of gaso-
hol in your engine,
Fuel stabilizer is an acceptable alterna-
tive in minimizing the formation of fuel
gum deposits during storage, Add stabi-
lizer to gasoline in fuel tank or fuel stor-
age container. Follow the mix instruc-
tions found on stabilizer container. Run
engine at least 3 minutes after adding
stabilizer,
Craftsman 40: 1, 2-cycle engine oil (air
cooled) is already blended with fuel
stabilizer. Ifyou do not use this Sears
oil, you can add a fuel stabilizer to your
fuel tank,
ENGINE
• Remove spark plug and pour 1 tea-
spoon of 40:1, 2-cycle engine oil (air
cooled) through the spark plug open-
ing, Slowly pull the starter rope 8 to
10 times to distribute oiL
• Replace spark plug with new one of
recommended type and heat range,
• Clean air filter.
• Check entire unit for loose screws,
nuts, and bolts, Replace any dam-
aged, broken, or worn parts,
• At the beginning of the next season,
use only fresh fuel having the proper
gasoline to oil ratio,
OTHER
• Do not store gasoline from one sea-
son to another,
• Replace your gasoline can if it starts
to
rust
-13 -

TROUBLESHOOTING TABLE
A WARNING: Always stop unit and disconnect spark plug before perform-
ing any ofthe recommended remedies below other than remedies that re-
quire operation of the
unit
TROUBLE CAUSE REMEDY
Engine will not
1. Engine flooded. 1. See "Starting a Flooded Engine"
start. in Operation section.
2. Fuel tank empty. 2. Fill tank with
correct fuel mixture.
3. Spark plug not firing.
3. Install new spark plug.
4. Fuel not reaching
4. Check for dirty fuel filter; replace.
carburetor.
Check for kinked or split fuel line;
repair or replace.
5. Compression low. 5. Contact Sears
Service (see back cover).
Engine w!il not 1. Fuel
not reaching 1.
Check for dirty fuel filter; replace.
idle properly. carburetor.
Check for kinked or split fuel line;
repair or replace.
2. Carburetor requires 2. Contact Sears
Service (see back cover).
adjustment.
3. Crankshaft seals worn.
3. Contact Sears Service (see back cover).
4. Compression low.
4. Contact Sears Service (see back cover).
Engine will not 1. Air filter dirty. 1. Clean or replace air filter.
accelerate, 2. Fuel not reaching
2. Check for dirty fuel filter; replace.
lacks power, or carburetor.
Check for kinked or split fuel line;
dies under a repair
or replace.
load. 3. Spark plug fouled.
3. Clean or replace spark plug
and re-gap.
4. Carburetor requires
4. Contact Sears Service (see back cover).
adjustment.
5. Carbon build up.
5. Contact Sears Service (see back cover).
6. Compression low.
6. Contact Sears Service (see back cover).
Engine
smokes
1. Choke partially on. 1. Adjust choke.
excessively. 2. Fuel mixture incorrect. 2. Empty fuel tank and refill with
correctfuel mixture.
3. Air filter dirty.
3. Clean or replace air filter.
4. Carburetor requires
4. Contact Sears Service (see back cover).
adjustment.
Engine runs hot. 1. Fuel mixture incorrect. 1. See "Fueling Engine" in Operation
section.
2. Spark plug incorrect.
2. Replace with correct spark plug.
3. Carburetor requires
3. Contact Sears Service (see back cover).
adjustment.
4. Carbon build up.
4. Contact Sears Service (see back cover).
- 14 -

U.S. EPA/CALIFORNIA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB·
LIGATIONS: The U.S. Environmental
Protection Agency/California Air Re-
sources Board and Sears, Roebuck and
Co., U.S.A., are pleased
to explain the
emissions control system warranty
on
your year 2007 and later small off-road
engine.
In California, all small off-road
engines rnust be designed, built, and
equipped
to rneet the State's stringent
anti-smog standards. Sears must war-
rant the emission control system on your
small off-road engine for the periods of
time listed below provided there has
been no abuse, neglect, or irnproper
maintenance of your small off-road en-
gine. Your emission control system in-
cludes parts such as the carburetor, the
ignition system and the fuel tank (Califor-
nia only). Where a warrantable condition
exists, Sears will repair your small off-
road engine engine at no cost to you.
Expenses covered under warranty in-
clude diagnosis, parts and labor.
MANUFACTURER'S WARRANTY
COVERAGE:
If any emissions related
part on your engine
(as listed under
Emissions Control Warranty Parts List)
is
defective or a defect in the materials or
workmanship of the engine causes the
failure of such an emission related part,
the part will be repaired or replaced by
Sears.
OWNER'S WARRANTY RESPONSIBI-
LITIES: As the small off-road engine
engine owner, you are responsible for
the petiormance of the required mainte-
nance listed
in your instruction manual.
Sears recommends that you retain
all
receipts covering maintenance on your
small off-road engine, but Sears cannot
deny warranty solely for the lack of re-
ceipts or for your failure
to ensure the
petiormance of
all scheduled mainte-
nance. As the small off-road engine en-
gine owner, you should be aware that
Sears may deny you warranty coverage
if your small off-road engine engine or a
part of
it has failed due to abuse, ne-
glect, improper maintenance, unap-
proved modifications, or the use of parts
not made or approved by the original
equipment manufacturer. You are re-
sponsible for presenting your small off-
road engine to a Sears authorized repair
center as soon as a problem exists.
Warranty repairs should be completed
in
a reasonable amount oftime, not to ex-
ceed 30 days.
If you have any ques-
tions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized selVice center or call
Sears at 1-800-469-4663. WARRANTY
COMMENCEMENT DATE: The warran-
ty period begins
on the date the small
off-road engine is purchased. LENGTH
OF COVERAGE: This warranty shall be
for a period oftwo years from the initial
date of purchase. WHAT
IS COV-
ERED: REPAIR OR REPLACEMENT
OF PARTS. Repair or replacement of
any warranted part will be petiormed at
no charge to the owner at an approved
Sears SelVice Center. If you have any
questions regarding your warranty rights
and responsibilities, you should contact
your nearest authorized selVice center
or call Sears at 1-800-469-4663. WAR-
RANTY PERIOD: Any warranted part
which
is not scheduled for replacement
as required maintenance, or which
is
scheduled only for regular inspection to
the effect of"repair or replace as neces-
sary" shall be warranted for 2 years. Any
warranted part which
is scheduled for
replacement as required maintenance
shall be warranted for the period oftime
up to the first scheduled replacement
point for that part. DIAGNOSIS: The
owner shall not be charged for diagnos-
tic labor which leads
to the determina-
tion that a warranted part
is defective if
the diagnostic work
is petiormed at an
approved Sears SelVice Center. CON-
SEQUENTIAL DAMAGES: Sears may
be liable for damages to other engine
components caused by the failure of a
warranted part still under warranty.
WHAT
IS NOT COVERED: All failures
caused by abuse, neglect, or improper
maintenance are not covered.
ADD-ON
OR MODIFIED PARTS: The use of
add-on or modified parts can be
grounds for disallowing a warranty claim.
Sears
is not liable to cover failures of
warranted parts caused by the use of
add-on or modified parts. HOW TO
FILE A CLAIM:
If you have any ques-
tions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized selVice center or call
Sears at 1-800-469-4663.
- 15 -

WHERE TO GET WARRANTY SER-
VICE: Warranty selVices or repairs shall
be provided at all Sears SelVice Cen-
ters. Call 1-800-469-4663.
MAINTENANCE, REPLACEMENT
AND REPAIR OF EMISSION RE-
LATED PARTS: Any Sears approved
replacement part used in the perror-
mance of any warranty maintenance or
repair
on emission related parts will be
provided without charge
to the owner if
the part
is under warranty.
EMISSION CONTROL WARRANTY
PARTS LIST: Carburetor, Ignition Sys-
tem: Spark Plug (covered up to mainte-
nance schedule), Ignition Module, Muf-
fier including Catalyst, Fuel Tank (Cali-
fomia only). MAINTENANCE STATE-
MENT: The owner is responsible for the
perrormance of
all required maintenance
as defined
in the instruction manual.
The Information on the product label indicates which standard your engine is certified,
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
~ Moderate (50 hours)
DIntermediate (125 hours)
DExtended (300 hours)
- 16 -

Ref. Part No.
1. 530015814
2. 545135806
3. 530015880
4. 545134001
5. 545099101
6. 545052401
7. 545052501
8. 545050407
9. 545054901
10. 530054834
11. 545081833
12. 545107101
13. 545081830
14. 545128201
15. 545099001
16. 545116201
17. 545113804
18. 545134105
19. 530015814
20. 545100801
21. 545115601
22. 545144501
23. 530016406
24. 545109901
25. 545113601
26. 545113701
27. 530015197
28. 530016386
29. 545161605
30. 545101201
31. 545100401
REPAIR PARTS
SEARS GAS BLOWER MODEL 358.794741
AWARNING
All repairs, adjustments and
maintenance not described in
the Operator's Manual must be
performed by Qualified Service
Personnel
Description Ref.
Screw 32.
Assy -Engine Cover 33.
Screw 34.
Shield -Baffle 35.
Baffle 36.
Hub
Spring -Pulley
Kit -Starter Pulley (Incl. 6.7)
Spring -Starter
Handle -Starter
Kit -Rope
Tube -Starter rope
Kit -Switch (Incl. 14)
Protector -Switch
Bearing
Nut -Lock
Trigger -Throttle
Assy -Scroll LH (Incl. 20.21)
Screw
Door -Vac
Spring -Vac door
Knob -Blower tube
Screw -Handle vac
Washer -Impeller
Assy -Impeller
Spacer -Flywheel
Nut -Blower Knob
Screw
Assy -Scroll RH (Incl. 15)
Handle -Vac
Assy -Fuel tank
(Incl. 32.33.34.35)
17
Part No. Description
530095646 Assy -Fuel Pickup
530069247 Kil -Fuel line (carb/purge)
530069216 Kil -Fuel line (lank/purge)
530057973 Assy -Fuel Cap with retainer
530016445
Screw -Fuel tank retainer
I Not Shown I
545154792 Operator Manual
545001245 Decal -Warning
545136304 Decal -Start Instruction

Ref.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
REPAIR PARTS
SEARS GAS BLOWER MODEL 358.794741
~{fln'.
m~/
17
AWARNING
All repairs, adjustments and
maintenance not described in
the Operator's Manual must be
performed by Qualified Service
Personnel
Part No. Description
545090001 Assy -Muffler (Incl. 2.3.4.5)
530015241 Screw
545081845 Kit -Spark Screen
530058982 Bolt -Muffler
545081832 Gasket -Muffler (gasket kit)
545115301 Cylinder
530015953 Bolt
Champion Spark plug (RCJ-6Y)
545084901 Adapter - Carbo
545115501 Linkage -Throttle
545081855 Kit -
Carbo Assy (WT-875A)
(Incl. 12.17)
545157103 Lever -Choke
545112603 Base -Airbox
530016429 Screw
545116801 Filter
545112702 Cover -
Air box filter
530035497 Bulb -Purge (Walbro 188-16)
21
545081832 O-ring (CarbjAdapter)(gasket kit)
530016441 Screw
545081832 O-Ring (AdapterjCyl.)(gasket kit)
545081864 Kit -Piston/Connecting Rod
(Incl. 22.23.24)
530012472 Ring -Piston
530015162 Retainer -Wrist Pin
545081865 Kit -Assy Connecting Rod
545158001 Module -Ignition
530016357 Screw
545127601 Assy -Wire Harness
545081832 O-ring seal -Crankcase (kit)
530015828 Washer
530054115 Assy -Flywheel
530015941 Retainer -Crankshaft
530055728 Bearing -Outer
530019264 Seal
l
®
Ref. Part No. Description
34. 530032125 Bearing -Inner
35. 530012582 Assy -Crankcase
(Incl. 32.33.34)
36. 545102102 Assy -Crankcase/Crankshaft
(Incl. 31.35)
37. 545081832
O-Ring (Rear plug)(gasket kit)
38. 530057954 Assy -Rear Plug (Incl. 37)
39. 530016386 Screw
40. 545081832 Kit -Gasket (Incl. 5.18.20.28.37)
18

REPAIR PARTS
SEARS GAS BLOWER MODEL 358.794741
Ref. Part No. Description
1. 545099401
Tube -Upper vac
2. 530095589
Tube - Lower vac
3. 545116601 Tube -J
4. 530095564 Assy -Vac bag
5. 545100501 Tube -Upper Blower
6. 545100601
Tube - Lower Blower
7. 545151201 Nozzle -High Speed
19