Creative Lighting Solutions Tanya User manual

CLS Manuals
CLS Atmosphere LED-panel
CLS Manuals
CLS Tanya
www.cls-led.com
version 1.2 August 2009
www.cls-led.com
- 4 - - 1 -
2007 CLS-LED BV. All rights reserved. Information subject to change without notice, CLS-LED BV and all affiliated companies disclaim liability for
injury, damage direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on
the information contained in this manual. No part of this manual may be reproduced, in any form or by any means, without permission in
writing from CLS-LED BV. Other legal information can be found in our General conditions to be found on the back of your CLS-LED BV invoice
or on our website www.cls-led.com/Conditions.pdf
TECHNICAL SPECIFICATIONS
LED: 1 x Luxeon®K2 + blue LED indication light
Colour: Extra warmwhite, 3150K (WW3)
Lens: 45º
Power supply: Voltage: 100 ~ 240 VAC
Power consumption: 10 VA
Measurements: ø70 x 76 mm (øxh)
Weight: 400 gr
Cable length: 2 meter
Swivel angle: + 5º / -45º, rotate 355º
Housing: Aluminum
Ambient temperature: Max. 40 ºC
CLS Tanya
Multiple connection
Possiblities on a fixture
Installation depth
In centimeters
Swivel
Fixture is horizontally rotatable,
indicated in degrees
Swivel
Fixture is vertically rotatable,
indicated in degrees
Mounting hole
In centimeters
Application area
Indoor or outdoor
Application area
Floor, wall or ceiling
Protection class
One, two or three
350º
350°
Cable length
Maximum cable attached
on the fixture in centimeters
Lifespan
Of the light source in hours
Driver
Inclusive or exclusive
Pressure
Maximum pressure on
the fixture per kg/cm2
Weight
In gram/kilogram
Curve
Minimal bending curve
in centimeters
Driver
Incl.
10.000 h
Driver
Excl.
200 cm
6 cm
LED pitch
Pitch between the
LEDs in millimeters
20 mm
15kg/cm2
4x4 cm
4 cm
4 cm
4 cm
4 cm
List of symbols

CLS Manuals
CLS Atmosphere LED-panel
www.cls-led.com
- 2 - - 3 -
INTRODUCTION
Thank you for choosing the CLS Tanya. The CLS Tanya is a compact yet powerful wall spot for numerous
applications. Easy use by a switch button on both sides, one for the Luxeon K2 LED and the other for the blue
LED indication light.
Included Items
The CLS Tanya is shipped in one package containing the following items:
• 1 user manual
• 1 mounting set
NOTE: It is important to read this manual before you install this product.
SAFETY INFORMATION
Warning! This product is for professional use only, not for domestic use.
Read this manual before powering up or installing the CLS Tanya. Follow the instructions as listed
below and observe all warnings in this manual.
Protection from electric shock
• Disconnect the power supply from AC power before installing, dismounting or maintaining the unit.
• Make sure all connectors are connected properly.
• Use only a source of AC power that complies with local building and electrical codes and has both
overload and ground-fault protection.
• Refer all service to a qualified technician.
Protection from burns and fire
• Do not install the CLS Tanya near a heat source.
• Do not install the CLS Tanya in a corrosive, flammable or explosive area.
• Do not modify the CLS Tanya, or install other besides genuine parts.
• Do not operate the CLS Tanya if the ambient temperature exceeds 40º C.
CLS Tanya
INSTALLATION
This section shows how to install the CLS Tanya.
Protection from injury due to falls
• Verify that all covers and mounting hardware is securely fastened.
• Block the access below the work area whenever installing or removing the unit.
Disassemble the ring with the
attached LED driver by loosening
the screw.
To install the fixture, drill two
screw holes and secure the ring
on the wall. Assemble the fixure
back on the ring.
Put the power wire in the earthed
socket and the product is ready
to use.
Available wall spots:
• CLS Tanya, black (item nr. 123000)
• CLS Tanya, silver (item nr. 123002)
76 mm
ø70 mm
+5º / -45º
355º
MEASUREMENTS