Saxby Lighting 73435 Manual

We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
Instruction leaflet
Zone & Dome LED Bollard
73435, 73436
www.saxbylighting.com
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Saxby Lighting,. BH23 3PE
Iss.1 01082018
• TheLEDsinthisproductarenonreplaceable.
Fitting/replacing bulbs
Care & Cleaning

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeandsatisfactory
operation of this product. Please retain these instructions for future reference.
Warning
This light fitting is Class 1 and must be connected to
an Earth circuit
Please read these instructions carefully before
commencing any work.
Thisunitmustbefittedbyacompetentandqualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
Topreventelectrocutionswitchoffatmainssupply
before installing or maintaining this fitting. Ensure other
persons cannot restore the electrical supply without
your knowledge. If you are in any doubt, please consult a
qualifiedelectrician.
Thislightfittingshouldbeconnectedtoacircuitwitha
30mA RCD fitted.
If replacing an existing fitting, make a careful note of the
connections.
Thissystemcontainsnon-replaceablepartsandcannotbe
serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
ThisproductisratedatIP65.
Thisproductisnotsuitablefordimming.
Thisproductisnotsuitableforlocationinorneara
marine or sea environment.
Thisproductmustbemountedontoaconcretebaseor
paving slab. It should not be directly installed in the soil.
An additional fixing kit for installation into wet concrete is
available separately part no: 73437.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 25W LED Module
IP rating: 65
Layout
• Planthedesiredlayoutofthisfittingcarefully,
ensuring the cables will reach the distance between the
connector and the light fitting
• Avoidlocatinganycablesinpositionsthatwould
cause a hazard. Position cables and junction boxes (not
supplied) away from areas where they may be at risk
from being cut, trapped or damaged
• Cablesinwallsmustbeprotectedusingsuitable
conduit or plastic trunking.
• Themainssupplycablemusthaveaminimumcross
sectional area of 1.0mm²
• Thisproducthasspecialprotectionagainsttheingress
of moisture and is IP65 rated.
• Thisproductmustbemountedontoaconcretebaseor
paving slab. It should not be directly installed in the soil.
• An additional fixing kit for installation into wet concrete is
available separately part no: 73437
Wiring
• ItisrecommendedthattheSaxbyIP68inline
connector ref 61515 is used to wire this product. Refer
to layout diagram.
• Unscrew the threaded body at the centre of the
connector from both sides (Fig. 3a).
• Push the wires into the terminals, observing the
correct polarity (Fig. 3b). Make sure the gaskets are in
place to ensure ingress protection.
• Tightenthescrewstosecureinplace(Fig.3c).
• Refit the seals and locking nuts.
Fig.
3a
Fig.
3b
Fig.
3c
Layout
• Placeproductoverthemountingunitandsecurein
place by refitting the three allen screws set aside earlier.
Ensure cable is not trapped (Fig. 4).
• Replace fuse or circuit breaker and switch on. Your light
is now ready for use.
Commissioning
Fig. 4
Installation
Existing fittings must be completely removed before installation
of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
• Undothe3allenscrewswiththesuppliedhexkeytodetach
the mounting unit from the product. Keep the 3 screws safe
for refitting later (Fig. 1).
• Positionthemountingunitonthesolidmountingsurface
and mark the position of the fixing holes. Drill the holes
taking care not to damage concealed wiring and pipes. If
using supplied fixings, ensure the holes have depth: 40mm
and diameter: 12mm.
• Positiontheconduitorplastictrunkingsothatthecable
comes up the centre point of the bollard. Ensure that the
cables do not snag.
• Usethesuppliedanchorbolts(Seeinsetforexpanded
diagram of bolt) or alternative fixings to secure the mounting
unit (Fig 2).
• Wire as detailed below.
Fig. 1
Fig. 2
EF
ABC D