Creative Play AS101 Instruction manual

ALPINE SHELTER
Assembly + Installation Instructions
REF: AS101 - ALPINE SHELTER
pg 1 of 26

x8 (M12 200 cup square hex)
x36 (M12 155 cup square hex)
x44 (M12 Nylocs)
x20 (End Caps)
PARTS required
REF: AS101 - ALPINE SHELTER
pg 2 of 26
ASF1
ASF1
ASF2
ASF2
ASF2
ASF2
FLOOR TIMBERS
ASF3
ASF3
ASF3
ASF4
4 x boards will be
‘NOTCHED’ to fit around the
upright timbers
x269 (FM80 BRASS SCREWS)
x500* (13mm FELT NAILS) approx.*
x500* (DECK SCREWS) approx.*

PARTS required
REF: AS101 - ALPINE SHELTER
pg 3 of 26
ASU1
ASU1
ASU1
ASU2
ASU3 ASU3
ASU2
ASU1
UPRIGHT TIMBERS
x4.5 PACKS (CURVED GREEN FELT ROOF SHINGLES)
EACH PACK CONSISTS OF 21 x 1m Felting
‘STRIPS’ and will cover 3m2

RIDGE BEAM
RAFTER with HOLES
ROOF TIMBERS ASR1
ASR1
ASR2
ASR2
ASR2
ASR2
ASR6
ASR7a / b
ASR5
ASR5
ASR4
ASR4
ASR3
ASR3
ASR3
ASR3
ASR3
ASR3
PARTS required
RIDGE CAP / COVER
ROOF TIMBERS additional
1
1
1
1
2
2
ASR10
ASR10
ASR8
ASR9
ASR8
ASR8
ASR8
REF: AS101 - ALPINE SHELTER
pg 4 of 26

PARTS required
REF: AS101 - ALPINE SHELTER
pg 5 of 26
FENCE PANELS
FENCE PANELS
SEAT SLATS (consists of
inner and outer parts)
SEAT SLATS (consists of
inner and outer parts)
3x LARGE
2x SMALL
2 x SMALL 3 x LARGE
9 x LEGS

TOOLS required
REF: AS101 - ALPINE SHELTER
pg 6 of 26

Foundation Details
REF: AS101 - ALPINE SHELTER
pg 7 of 26
*FOUNDATIONS NOT REQUIRED - PLEASE MARK THE AREA /
POSITION THE TIMBERS
MUST BE INSTALLED ONTO A LEVEL SURFACE

1
2
Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 8 of 26
Attach the UPRIGHT timbers to the FLOOR timbers
Using M12 square cup hex bolts / nylocs
Attach using M12 bolts and nylocs
End caps NOT required as the decking will cover the nuts
ASF1
ASF1
ASF1
ASU2
ASU2
ASU3
ASU3
ASU1
ASU1
ASU1
ASU1
ASU1
ASF2
ASF2
M12 x 155 BOLTS / NYLOCS
M12 x 200 BOLTS / NYLOCS

Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 9 of 26
3
4
Bolt the UPRIGHT ‘BLOCK’ to the Floor timbers 1 / 2
Ensure the correct BOLTS will be used
Bolt the ROOF timbers (ASR5 / ASR6) to the corner up-
right timbers (ASU1 )
Using M12 x 155 cup square hex bolts
M12 x 155 BOLTS / NYLOCS
M12 x 200 BOLTS / NYLOCS
ASU3
ASR5
ASR5
ASR6
ASR6

5
Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 10 of 26
Ensure END CAPS are used
End caps must be positioned on the inside

Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 11 of 26
6
7
Bolt the ASR2 timber (rafter with holes) to the ASU1 / 2
Uprights Using M12 x 155 square cup hex bolts / nylocs / end caps
Attach the ASR7a / ASR7b timbers
Using FM80 Brass screws
ASR7a / b
ASU2
ASU1

8
9
Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 12 of 26
Screw from the INSIDE No Screw be be screw from the outside for these PARTS
Drop the RIDGE BEAM ASR1 into position
Attach using FM80 Brass screws
SCREW HOLES LOCATIONS

Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 13 of 26
10
11
Ensure the BACK is ‘FLUSH’
Circled BELOW RIGHT
Attach the remaining rafters to the ASR5 / ASR1 roof
timbers using brass screws
Remaining rafters are WITHOUT HOLES
ASR5
ASR5
ASR1

12
Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 14 of 26
Rafters MUST be spaced correctly
This is to ensure the PLYWOOD FITS CORRECTLY
ASR3
ASR3
ASR3
ASR3
ASR3
ASR3

Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 15 of 26
13 Attach the ASR4 timbers to the RAFTERS
Using FM80 Brass screws
ASR4
ASR2
ASR3
Bottom EDGE flush with corner -
as shown RIGHT
ASR4

Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 16 of 26
14 Attach the PLYWOOD SHEETS to the RAFTERS
Using FM80 Brass screws
Notes:
Edge of PLYWOOD flush with the
centre of the RIDGE BEAM
Edge of PLYWOOD flush with face
of ASR4 timber
1
1
2
NARROW plywood sheet is
positioned at the BACK
ASR4
RIDGE BEAM

Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 17 of 26
15
16
Ensure they are positioned CORRECTLY
Repeat for the OPPOSITE SIDE
211

Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 18 of 26
17 Attach felt shingles to the PLYWOOD SHEETS
Using FELT NAILS
Notes:
TURN the first ‘ROW’ the opposite way round to create a
straight edge
STRAIGHT edge to be attached tot the ASR4 timber
Ensure:
The first ROW (which are positioned upside
down) are all in line - approx positioned
50mm down the ASR4 timbers
ASR4
ASR4

Notes:
Only the FIRST ROW are positioned ‘UPSIDE DOWN’
a
d
b
e
c
f
Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 19 of 26
18 Continue to attach the FELT SHINGLES to the PLYWOOD
SHEETS Using FELT NAILS
Notes:
The SECOND ROW will positioned AS SHOWN RIGHT
Attach the SHINGLES
ROW by ROW

REPEAT STEPS to
for the OPPOSITE SIDE
Assembly Instructions
REF: AS101 - ALPINE SHELTER
pg 20 of 26
19
20 17 19
TOP OF THE SHEET - If required TRIM the last row of
SHINGLES to suit
Notes:
There is a TIMBER cover to cover the
TWO SIDES