Creek Company Outdoor Discovery Craft ODC 420 User manual

ODC 420
Outdoor Discovery Craft
Your ODC 420™ Includes:
(1) ODC 420™ Outer Cover (1) Stripping Apron (1) Valve Adapter
(2) Air Bladders (1) Foam Fly Patch (1) Valve Wrench
(1) Foam Seat Bottom (1) Air Bladder Patch Kit (1) Warranty Card
(1) Foam Seat Back
ODC 420™Outer Cover, Air Bladders, Foam Seat Bottom, Foam Seat Back, Foam Fly Patch
and Stripping Apron all pre-assembled.
Your ODC 420™ is designed to give you many years of service. Please follow Ination Instructions, and Care and
Maintenance Instructions and Warnings carefully. If you ever have any questions or problems with your ODC 420™ please
call The Creek Company at [phone] or E-mail us at [e-mail]. We are open 9am-5pm, Mountain-
Time, Monday-Friday
Your ODC 420™ is guaranteed against defects in material and workmanship for the life of the product to the
original owner. This does not cover damage due to misuse or normal wear and tear.
HIN is located on outboard, starboard side of the hull aft.
Warning:
1. Always wear a U.S. Coast Guard approved personal otation device when in your ODC 420™
2. The ODC 420™ is intended for use in still waters only. Never use your ODC 420™ in moving waters.
3. Never oat alone.
4. Always check your ODC 420™ Air Bladders, Outer Cover and stitching for possible damage
before you use your ODC 420™.
5. Never use your ODC 420™ if you suspect the Air Bladders, Outer Cover or Stitching has
been damaged.
6. Never over inate your ODC 420™.
7. Never use your ODC 420™ without both Air Bladders fully inated.
Care and Maintenance:
1. In case of puncture, Air Bladder Patch Kit is included.
2. Do not store your ODC 420™ in direct sunlight.
3. If you are leaving your ODC 420™ out in the sun for any amount of time, be aware that the heat
can increase the pressure inside the Air Bladders to a dangerous level. Let some of the air out of the Bladders if it
will be out of the water in the sun for any length of time, or if it is stored in a vehicle, etc.
4. A gain in altitude will increase the pressure in the Bladders also. If you are taking your inated ODC 420™
from a low elevation to a high elevation, be sure to let some of the air out of it.
5. For short term storage, we recommend you let some of the air out of your ODC 420™.
6. For long term storage, we recommend you make sure your ODC 420™ is completely dry and
deated and stored out of the sunlight in a cool dry area.
™
Accessories are available for your ODC 420™. Ask for them where you bought your ODC 420™,
or visit The Creek Company Store at www.CreekCompany.com
The Creek Company, PO Box 773892, Steamboat Springs, CO 80477
email: [email protected] • Made in China Specifications and other details subject to
change without notice.

Inflating Your Creek Company ODC 420
™
VALVES
The ODC 420™ features the Pro Series Push Button Valve on the main bladders (see illustration 3). To open the Pro Se-
ries Valve, rst remove the valve cap. Then press down on the spring-loaded valve stem and turn it counter-clockwise 1/4
turn. The valve stem is now locked down in the open position, allowing air to move freely in and out through the valve. To
close the valve, push down on the valve stem and turn clockwise 1/4 turn. The stem will pop back up, sealing the valve
shut. In the closed position, you can still pump air into the chamber, but when you remove the pump, the valve will not al-
low air to escape. When you’re done, screw the plastic valve cap back on to keep water and dirt out of the valve.
INFLATION
Unscrew the plastic Valve Cap (see illustration 3) on the Pro Series Push Button Valve. Push Down on the Valve Stem
and turn ¼ turn clockwise so the Valve Stem pops up into the closed position. Using any standard double action hand
pump (not included) and adaptor (included), insert the adaptor into the valve and turn clockwise ¼ turn, locking the
adaptor in place. Connect the pump/pump adaptor to the Valve Adaptor and inate until rm. Do not overinate. When
the tube is fully inated, you’ll notice all the wrinkles in the cover will atten out.
To deate the tube, push down on the Valve Stem and turn it counter-clockwise ¼ turn. This locks the valve open for
deation.
Features found on your Creek Company ODC 420™
(see Illustrations 1,2 and 3)
1. Pro Series Push Button Valves
2. Insulated Drink Holder
3. Carry Handles (top & bottom)
4. D-rings to attach Pack Straps (Pack Straps not included).
5. D-Rings to attach gear (two on nose of Pontoons and two on outside
of Pockets).
6. Pockets with ve separate storage areas plus mesh for additional
storage.
7. Foam Fly Patch for drying and storage of ies.
8. Stripping Apron for collecting your y line.
9. Adjustable Seat Back for comfort
10. Handy Ruler on Stripping Apron to measure sh.
11. Grommets for water drainage
Valve Cap
Spring
Loaded
Valve
Stem
ILLUSTRATION 3
Pro Series Push
Button Valve
Carry Handle
Seat Bottom
Seat Back
Stripping Apron Stripping Apron
Pocket Pocket
Foam
Fly
Patch
D- RIngs to
attach optional
Pack Straps
(Pack Straps
not included)
Grommets
ILLUSTRATION 1
top view ILLUSTRATION 2
bottom view
Drink
Holder
Pro Series Push
Button Valve
D- RIngs
Pro Series Push
Button Valve
Grommets
D- RIngs
HIN Location