Crestron DigitalMedia DM-MD6X4 Operator's manual

The Crestron® DM-MD6X4 and DM-MD6X6 DigitalMedia™ Distribution
Centers direct multiple high-definition sources to up to four rooms
(DM-MD6X4) or up to six rooms (DM-MD6X6) as part of a complete
Crestron system.
In the Box
1 DM-MD6X4 or DM-MD6X6, DigitalMedia Distribution Center
Additional Items
2 Bracket, Rack Ear (2029724)
4 Foot, 0.5 in. x 0.5 in. x 0.23 in., Adhesive (2002389)
1 Cable, Power, 6 ft 7 in. (2m) (2001134)
Install the Device
The device can be mounted into a rack or placed on a flat surface.
Mount into a Rack
To install the included rack ears:
1. Use a #1 or #2 Phillips screwdriver to remove the three screws from
each side of the front of the device as shown in the following
illustration.
2. Use the screwdriver and the screws removed in step 1 to attach the
included rack ears to the device.
Place on a Flat Surface
Attach the included feet near the corners on the underside of the device
before placing the device onto a flat surface or stacking it with other
equipment.
1
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

Connect the Device
Connect the device as called out in the illustration below. Refer to the
information that follows.
Rear Panel Connections (DM-MD6X6 Shown)
2
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

HDMI® Input Connections
Use HDMI cables to connect up to six HDMI digital video/audio devices to
the HDMIinput connectors (HDMI 1 to HDMI 6).
HDMI Output Connection
Use an HDMI cable to connect and HDMI digital video/audio device to the
HDMIoutput connector (HDMI 1).
DM 8G+® Output Connections
Connect up to three (DM-MD6X4) or five (DM-MD6X6) Crestron
DigitalMedia 8G+® receivers/room controllers to the DM 8G+ output
connectors (DM 2 to DM 4 on the DM-MD6X4 or DM 2 to DM 6 on the
DM-MD6X6). HDBaseT® Alliance-certified display devices can also be
connected without requiring any DM® receivers.
For DM 8G+ or HDBase T wiring up to 330 feet (100 meters) between
devices, use Crestron DM-CBL-8G DigitalMedia 8G™ cable or generic
CAT5e (or better) UTP or STP.
NOTE: Shielded cable and connectors are recommended to safeguard
against unpredictable environmental electrical noise that may impact
performance at resolutions above 1080p.
USB HIDConnection
Use a USB cable with a type B female connector to connect a host
computer or other USB HID-compliant host to the USB HID port.
LAN Connection
Use an RJ-45 cable to connect the 8-pin LANport to the
10BaseT/100Base-TX Ethernet network.
Power Connection
NOTE: The DM-MD6X4 and DM-MD6X6 do not have a power switch.
Power is applied to the device when the supplied power cable is
connected to an AC power source.
Connect one end of the included power cable to the device and the other
end to an AC power source.
3
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

Configure the Device
Use the front panel controls to configure the device.
Access Installer Mode
1. Ensure that the home screen is displayed. If it is not displayed, press
the HOME button.
Home Screen (DM-MD6X6 Shown)
After 30 seconds of inactivity, the device times out, returns to the
Home screen, and dims the LCD.
2. Press the BACK button. The Installer password screen is displayed.
Installer Password Screen
3. Enter the four-digit password. (The default password is 1234.) To enter
a digit, do either of the following:
lIf the digit ranges from 1-6, press the corresponding INPUTor
OUTPUTbutton.
lIf the digit is 0 or ranges from 7-9, use the navigation pad as
follows:
Press the Up or Down navigation button as necessary until the
desired digit appears between the brackets, and then press the
Select button in the center of the navigation pad.
After the fourth digit is entered, the Installer menu is displayed.
Set Input and Output Names (Optional)
For inputs 1-6, the default names are Input 1,Input 2, and so on. For
outputs 1-4 (DM-MD6X4) or outputs 1-6 (DM-MD6X6), the default
names are Output 1,Output 2, and so on.
To change an input name:
1. In the Installer menu, navigate to Inputs if it is not already highlighted,
and then press the Select button on the navigation pad.
Installer Menu
4
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

The Input submenu for the currently selected input is displayed. The
name of the input is shown at the top of the Input submenu. (The LED
of the currently selected input lights.)
2. Select the desired input by pressing the appropriate INPUT button
(1-6). The LED of the selected input lights, and the name of the input
appears at the top of the Input submenu.
3. Navigate to Name if it is not already highlighted, and them press the
Select button. A scrollable list of predefined source names is displayed
for the input.
4. Navigate to the desired name in the list, and then press the Select
button to confirm the selection. The selected name for the input is now
displayed at the top of the Input submenu.
To change an output name:
1. In the Installer menu, navigate to Outputs, and then press the Select
button.
The Output submenu for the currently selected output is displayed.
The name of the output is shown at the top of the Output submenu.
(The LED of the currently selected output lights.)
2. Select the desired output by pressing the appropriate OUTPUT button
(1-4on the DM-MD6X4 or 1-6on the DM-MD6X6). The LED of the
selected output lights, and the name of the output appears at the top
of the Output submenu.
3. Navigate to Name if it is not already highlighted, and them press the
Select button. A scrollable list of predefined room names is displayed
for the output.
4. Navigate to the desired name in the list, and then press the Select
button to confirm the selection. The selected name for the input is now
displayed at the top of the Output submenu.
Configure Network Parameters
To configure network parameters:
1. In the Installer menu, navigate to Network, and then press the Select
button.
Installer Menu
The Network submenu is displayed.
Network Submenu
2. If necessary, configure DHCP (Dynamic Host Configuration Protocol).
DHCP is enabled by default (set to On).
To disable DHCP:
a. Navigate to DHCP, and then press the Select button.
The DHCP configuration screen is displayed.
b. Navigate to Off, and then press the Select button.
DHCP is disabled. The screen returns to the Network submenu.
5
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

3. This step is applicable only if DHCP was disabled in step 2.
If necessary, configure a static IP address, a subnet mask address, and
a default router IP address. Navigate to the appropriate parameter
listed in the Network submenu (Address,Subnet Mask, and Default
Router), and then press the Select button. The corresponding
configuration screens are displayed as shown below.
IP Address (Static) Configuration Screen
Subnet Mask Configuration Screen
Default Router Configuration Screen
To enter a static IP address, a subnet mask address, and a default
router IP address, use the navigation pad. For each octet, press the Up
or Down navigation button until the desired number appears, and then
press the Select button.
After the last octet for each parameter is entered, the screen returns
to the Network submenu.
NOTE: Changes to network parameter settings take effect when the
device exits Installer mode and automatically reboots. A message is
displayed on the LDC screen indicating that the device is rebooting.
Configure Control System Parameters
To connect the device to a control system, use the following procedure to
configure control system parameters:
1. In the Network submenu, navigate to Control System, and then press
the Select button.
Network Submenu
The Control System submenu is displayed.
Control System Submenu
6
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

2. Configure the following parameters:
lNavigate to IP ID if it is not already selected, and then press the
Select button. The IP ID configuration screen is displayed.
IP ID Configuration Screen
Configure the IP ID of the device. The value ranges from 03 (default
setting) to FE, and it must match the IP ID specified in SIMPL
Windows and the value on the control system's IP table for the
DM-MD6X4 or DM-MD6X6.
In the IP ID configuration screen, specify the IP ID by pressing the
Up or Down button on the navigation pad until the desired value
appears, and then press the Select button.
The screen returns to the Control System submenu.
lNavigate to IP Address, and then press the Select button. The Ctrl
Sys IP Addr configuration screen is displayed.
Ctrl Sys IP Addr Configuration Screen
Configure the IP address of the control system. For each octect in
the IP address, press the UP or Down navigation button until the
desired number appears, and then press the Select button.
The screen returns to the Control System submenu.
Exit Installer Mode
To exit Installer mode, return to the home screen by pressing the HOME
button.
NOTE: The home screen can also be accessed by pressing the BACK
button as necessary or by allowing the DM-MD6X4 or DM-MD6X6 to
time out after 30 seconds of inactivity.
7
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

Route the Signal
An input signal can be routed to one or more outputs simultaneously. One
or more routed signals can also be disconnected simultaneously.
To route an input signal:
1. Ensure that the home screen is displayed. The DM-MD6X4 and
DM-MD6X6 are in Route mode when the home screen is displayed.
NOTE: By default, the input LEDs on the DM-MD6X4 and
DM-MD6X6 are not lit. The output LEDs of unrouted outputs are
lit.
2. Press the INPUT button that corresponds to the input to be routed.
INPUT buttons are numbered 1-6. The LED of the selected input lights.
In addition, the video and audio information for the selected input is
provided on the LCD screen. The LED of each destination output this
input is currently routed to also lights.
3. Press the OUTPUT button(s) that correspond(s) to the desired output
(s).
NOTE: For the DM-MD6X4, up to four OUTPUTbuttons, numbered
1-4, can be pressed for the selected input. For the DM-MD6X6, up
to six OUTPUTbuttons, numbered 1-6, can be pressed for the
selected input.
The LED(s) of the selected output(s) flash. In addition, the following
message appears on the LCD screen:
Press Select to Route
Press Back to Cancel
4. As indicated on the LCD screen, press the Select button to route the
signal. The selected input is routed to the selected output(s). The LED
of each selected output lights.
NOTE: After 30 seconds of inactivity, the DM-MD6X4 or
DM-MD6X6 times out. Input LEDs that were lit become unlit.
Output LEDs that were lit for routed signals also become unlit. In
addition, the DM-MD6X4 or DM-MD6X6 returns to the home
screen while also dimming the LCD.
To disconnect routed signals:
1. Ensure that the home screen is displayed.
NOTE: The LEDs of all routed outputs are not lit.
2. Press the OUTPUT button(s) the correspond to the output(s) to be
disconnected. The LED of the selected output(s) flashes.
3. Press the Select button. The selected outputs are disconnected. The
LED of each selected output lights.
8
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers

Visit the Product Page
Scan the QR code to visit the product page.
DM-MD6X4
www.crestron.com/model/6504420
DM-MD6X6
www.crestron.com/model/6504868
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, DM,
and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. HDBaseT is either a trademark or
registered trademark of the HDBaseT Alliance in the United States and/or other
countries. HDMIis either a trademark or registered trademark of HDMI Licensing LLC
in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Crestron disclaims any proprietary interest in
the marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2020 Crestron Electronics, Inc.
Doc. 7218C
04/29/20
9
DM-MD6X4/DM-MD6X6 QuickStart
DigitalMedia™ Distribution Centers