Crestron TMK-1000L User manual

Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Installation Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2002 Crestron Electronics, Inc.

Crestron TMK-1000L & WMKT-1000L Trim Ring Mount Kits
Trim Ring Mount Kits:
TMK-1000L & WMKT-1000L
Description
Trim Ring Mount Kits are the preferred mounting option for the Series 1000 wall
mounted touchpanels when a finished appearance within a neatly trimmed cutout is
required. This application is perfect for wallpapering.
There are two Trim Ring Mount Kits. The TMK-1000L is a pre-construction
accessory. Pre-construction refers to framed walls prior to hanging drywall. This
accessory is designed for use with the Pre-Construction Mount Kit (PMK-1000L) or
Back Box Kit (BB-1000L).
The WMKT-1000L is a post-construction kit. Post-construction refers to framed
walls with drywall hung. This accessory is designed with a mounting plate so that it
can be placed anywhere on a wall without the support from a stud.
NOTE: If necessary, consult the latest revision of the Series 1000 Operations Guide
(Doc. 5813) for a complete list of mounting options.
Supplied Hardware
Both Trim Ring Mount Kits contain a trim plate. The WMKT-1000L also contains a
mounting plate, which is the item that provides the necessary support for post-
construction applications.
Supplied Hardware of the TMK-1000L and WMKT-1000L
DESCRIPTION PART NUMBER QUANTITY
Metal Plate, Mounting
(WMKT-1000L only)
MTPL02832-1 1
Metal Plate, Trim Ring MTPL02834-1 1
Installation Guide – DOC. 6063 Trim Ring Mount Kits: TMK-1000L & WMKT-1000L •1

Trim Ring Mount Kits Crestron TMK-1000L & WMKT-1000L
Installation
This section provides an installation procedure for each Trim Ring Mount Kit. The
procedure for the TMK-1000L starts below and the “WMKT-1000L Procedure”
starts on page 3.
TMK-1000L Procedure
The procedure in this section provides the necessary steps for the assembly of the
TMK-1000L to either the PMK-1000L or BB-1000L. It is assumed that the
PMK-1000L or BB-1000L has been secured to the stud according to the procedures
in the latest revisions of their respective Installation Guides (Doc. 6061 and Doc.
6060, respectively). Also, it is assumed that drywall is in place and a square cutout
for the touchpanel is made in the drywall (measuring 4½ inches wide (114 mm) x 4½
inches high (114 mm)).
Complete the steps in the order provided. The only tool required and not supplied is
a level.
NOTE: When installing into the PMK-1000L, verify that the 18 AWG bus wire
securing the cable for the touchpanel remains attached.
1. Verify that the square cutout in the drywall measures 4½ inches wide
(114 mm) x 4½ inches high (114 mm) and is level.
2. Insert the symmetrical trim plate into the opening, as shown in the
illustration after this step.
Insert Trim Plate into Opening
TRIM PLATE
DRYWALL CUTOUT:
412in WIDE x 412in HIGH
(114 mm WIDE x 114 mm HIGH)
2 •Trim Ring Mount Kits: TMK-1000L & WMKT-1000L Installation Guide – DOC. 6063

Crestron TMK-1000L & WMKT-1000L Trim Ring Mount Kits
3. When the trim plate is in position, bend the top two flanges of the plate
upward and the bottom two flanges downward.
• If mounting into the PMK-1000L, bend the flanges
approximately 90 degrees.
• If mounting into the BB-3000L, bend the flanges back as far
as they can go.
4. The touchpanel can be installed using the four tapped holes in the
PMK-1000L or BB-1000L. Refer to the latest revision of the
Series 1000 Operations Guide (Doc. 5813) for details.
WMKT-1000L Procedure
The procedure in this section provides the necessary steps for installation of the
WMKT-1000L into a wall. Complete the steps in the order provided. The only tools
or materials required and not supplied are a drywall saw or equivalent and a level.
1. Locate an area on the wall that is free of miscellaneous wiring and
studs.
2. Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level and smooth as possible. The mounting plate allows
for only minor leveling adjustments. If a larger cutout is accidentally made, consider
purchasing the Crestron Mud Mount Kit, MMK-1000L. It and the mounting plate
supplied with the WMKT-1000L provide a cost-effective means of correction.
Essentially, the combination of these two kits makes up the Crestron Mud Mount Kit
for the Wall, WMKM-1000L. Simply follow the “WMKM-1000L Procedure” in the
latest revision of the Mud Mount Kits Installation Guide (Doc. 6062).
3. Use the drywall saw or equivalent to produce a level, square cutout in
the drywall that measures 4½ inches wide (114 mm) x 4½ inches high
(114 mm).
4. Insert the symmetrical trim plate into the opening, as shown in the
illustration after this step.
Installation Guide – DOC. 6063 Trim Ring Mount Kits: TMK-1000L & WMKT-1000L •3

Trim Ring Mount Kits Crestron TMK-1000L & WMKT-1000L
Insert the Trim Plate into the Opening
TRIM PLATE
DRYWALL MOUNTING PLATE
DRYWALL CUTOUT:
412in WIDE x 412in HIGH
(114 mm WIDE x 114 mm HIGH)
5. Carefully pass the mounting plate through the opening and rest it
against the interior surface of the drywall.
6. When the mounting plate is in position, bend the top two flanges of the
trim plate upward (approximately 90 degrees) and the bottom two
flanges downward (approximately 90 degrees). Refer to the illustration
after this step.
NOTE: The mounting plate will have slight play; this is normal. It allows for minor
adjustments to the touchpanel during installation.
Bend Flanges
BEND THESE TABS UP
TABS DOWN
BEND THESE
4 •Trim Ring Mount Kits: TMK-1000L & WMKT-1000L Installation Guide – DOC. 6063

Crestron TMK-1000L & WMKT-1000L Trim Ring Mount Kits
7. Run the necessary cables for the touchpanel and secure them behind the
drywall.
8. The touchpanel can be installed using the four tapped holes in the
mounting plate. Refer to the latest revision of the Series 1000
Operations Guide (Doc. 5813) for details.
Installation Guide – DOC. 6063 Trim Ring Mount Kits: TMK-1000L & WMKT-1000L •5

Trim Ring Mount Kits Crestron TMK-1000L & WMKT-1000L
Further Inquiries
If after reviewing this Installation Guide, you cannot locate specific information or
have questions, please take advantage of Crestron's award winning customer service
team by calling:
• In the US and Canada, call Crestron’s corporate headquarters at
1-888-CRESTRON [1-888-273-7876].
• In Europe, call Crestron International at [phone].
• In Asia, call Crestron Asia at [phone].
• In Latin America, call Crestron Latin America at [phone].
• In Australia and New Zealand, call Crestron Pacific at
[phone].
As of the date of manufacture, the TMK-1000L and WMKT-1000L have been tested
and found to comply with specifications for CE marking.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of
the TMK-1000L or WMKT-1000L, additional information may be made available as
manual updates. These updates are solely electronic and serve as intermediary
supplements prior to the release of a complete technical documentation revision.
Check the Crestron website (www.crestron.com) periodically for manual update
availability and its subjective value. Updates are available from the Download |
Product Manuals section and are identified as an “Addendum” in the Download
column.
6 •Trim Ring Mount Kits: TMK-1000L & WMKT-1000L Installation Guide – DOC. 6063

Crestron TMK-1000L & WMKT-1000L Trim Ring Mount Kits
Installation Guide – DOC. 6063 Trim Ring Mount Kits: TMK-1000L & WMKT-1000L •7
This page intentionally left blank.

Trim Ring Mount Kits Crestron TMK-1000L & WMKT-1000L
This page intentionally left blank.
8 •Trim Ring Mount Kits: TMK-1000L & WMKT-1000L Installation Guide – DOC. 6063