Crestron TSW-UMB-60 User manual

TSW-UMB-60/-60-PMK/-560P-PMK
Touch Screen Mounting Bracket/Kits
Installation Guide
Additional Resources
Visit the product page on the Crestron website
(www.crestron.com) for additional information and the
latest rmware updates. Use a QR reader application
on your mobile device to scan the QR image.
TSW-UMB-60 TSW-UMB-60-PMK
TSW-UMB-60 Installation
Use the included cutout template to ensure that the
correct dimensions are retained during the installation
process.
The template provides dimensions for installing the
bracket horizontally (for the TSW-560, TSW-760, or
TSW-1060) and vertically (for the TSW-560P).
3.75 in
(96 mm)
2.20 in
(52 mm)
TSW-UMB-560P-PMK
Description
The TSW-UMB-60 is a universal mounting bracket that
can be used with the Crestron® TSW-560, TSW-760,
and TSW-1060 touch screens, as well as with the
TSW-560P portrait touch screen. The TSW-UMB-60 is
designed for postconstruction installation in existing
drywall or paneling. The bracket is also suitable for use
in a lectern or a podium.
For preconstruction applications, the TSW-UMB-60 can
be installed along with the TSW-UMB-60-PMK or
TSW-UMB-560P-PMK preconstruction mounting kits.
The TSW-UMB-60-PMK and TSW-UMB-560P-PMK
permit fastening to the left- or right-hand stud of a
framed wall prior to the installation of drywall for
landscape and portrait touch screen installations,
respectively.
To install the TSW-UMB-60, follow the below steps:
CAUTION: Allow an air gap of at least
12" (305 mm) in the wall cavity above and below the
TSW-UMB-60 for heat dissipation.
1. Place the included cutout template (40151) in the
desired location, ensuring it is level. Place the
template horizontally if installing the TSW-560,
TSW-760, or TSW-1060, or place the template
vertically if installing the TSW-560P.
2. Trace the cutout all the way around the opening,
and then cut the hole with an appropriate drywall
saw.
NOTE: Do not remove the screws holding the
two parts of the assembly together.
3. Loosen the two screws on the mounting bracket,
and then install the assembly into the opening,
bottom rst, as shown in the illustrations that
follow steps four and ve.
For portrait mounting, install the assembly into the
opening left side rst so that the “TOP” text on
the inside of the back box is facing to the right.
Installing the Assembly into the Opening
CAUTION: To avoid damage to the
TSW-UMB-60, do not overtighten the screws.
TSW-UMB-60
TSW-UMB-60 Cutout Template Dimensions

4. Reach into the TSW-UMB-60 assembly and push
the rear half back to ensure it is fully behind the
mounting surface. Ensure the front of the
TSW-UMB-60 assembly is level.
For portrait mounting, allow the bracket to angle
into the opening (left side rst) before tightening.
Pushing the Rear Half Behind the Mounting Surface
Push the top surface
downward to install
the bottom half rst.
TSW-UMB-60
Loosen both
of the screws.
5. Tighten the two screws to complete the
installation.
Completing the Assembly
Push the rear half
back.
Ensure the front
is level, and then
tighten both screws.
TSW-UMB-60/-560P-PMK Installation
The TSW-UMB-60-PMK supports preconstruction and
postconstruction mounting applications for the
TSW-560, TSW-760, and TSW-1060 touch screens,
while the TSW-UMB-560P-PMK supports
preconstruction and postconstruction mounting
applications for the TSW-560P portrait touch screen.
• For preconstruction applications, use standard
drywall nails or screws to attach the PMK to a
wall.
CAUTION: Allow an air gap of at least
12" (305 mm) in the wall cavity above and below
the TSW-UMB-60 for heat dissipation.
Attaching the TSW-UMB-60-PMK to a Wall
• For postconstruction applications, use the PMK
as a cutout template by turning it to face the wall,
ensuring it is level, and temporarily tacking it to
the wall with nishing nails in the smaller holes
around the cutout opening. Trace the cutout
opening with an appropriate drywall saw.
TSW-UMB-60-PMK
Use a tie wrap to hold
the cable until the touch
screen is mounted.
Use a tie wrap to hold
the cable until the touch
screen is mounted.
TSW-UMB-560P-PMK
Attaching the TSW-UMB-560P-PMK to a Wall
Product warranty can be found at
www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at
patents.crestron.com.
Certain Crestron products contain open source software. For
specic information, please visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the
United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks
and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or
photography.
This document was written by the Technical Publications
department at Crestron.
©2017 Crestron Electronics, Inc.
Crestron Electronics, Inc. Installation Guide
15 Volvo Drive DOC. 7911B
Rockleigh, NJ 07647 (2047690)
Tel: 888.CRESTRON 03.17
Fax: [phone] Specications subject to
www.crestron.com change without notice.