Crosley C200A User manual

C200A
C200 Turntable
Instruction Manual
Questions, problems, missing parts?
Before returning to the store, call Customer Service
8 a.m. –6 p.m., EST, Monday –Friday
1-888-CROSLEY
www.crosleyradio.com

English
2
Safety Instructions
Read and understand this entire manual before using this product. Keep these instructions for future
reference.
1. Read these instructions carefully.
2. Keep these instructions for later reference.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use the device near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Always ensure a sufficient ventilation. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices
(including amplifiers) that produce or radiate heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades, one being wider than the other. A grounding- type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched or otherwise damaged, particularly
at plugs, convenience receptacles, and the point where they exit from the device.
11. Only use attachments/accessories that have been specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold
along with the device. When a cart is used, use caution when moving the cart/device
combination to avoid injury from tip-over.
13. Unplug this device during lightning storms or when not being used for longer periods of time.
14. Refer all servicing to qualified service personnel only. Servicing is required when the device has
been damaged in any way, such as: Power-supply cord or plug has been damaged, liquid has been
spilled or entered the device, the device has been exposed to rain or moisture, or objects have
fallen into the device, the device does not work normally, or it has been dropped.
15. Where a mains plug is used as the disconnect device, the disconnect device shall remain readily
operable.
16. Please keep the unit in a good ventilation environment at any time.

English
3
−Caution Marking and rating plate was located at rear enclosure of the apparatus.
−When the mains plug or appliance coupler is used as disconnect device, it shall remain readily
operable.
−The ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers, tablecloths, curtains, etc.; Minimum distances 10cm around the apparatus for sufficient
ventilation.
−No naked flame sources, such as lighted candles, should be placed on the apparatus.
−Use the apparatus only in a moderate climate.
−Element 1a: IEC 60417-6043 (2011-01)
−Element 2: *Sharp edges** or equivalent text
−Element 3: Optional
−Element 4: *Do not touch* or equivalent text

English
4
Items in this package
Before throwing away any packaging materials, please check thoroughly and
make sure you find the following items that come along with this package:
•Turntable
•Turntable Lid
•Turntable Platter
•Turntable slip mat
•Headshell
•45 RPM adapter
•Tonearm Counterweight
•Power adaptor
Please contact Crosley customer service if there is any accessory missing from
the package. Retain the original packaging materials for exchange or return
purposes.
Specifications
Power AC power adaptor, DC output 12V 2A
Turntable speed 331/3, 45 RPM
Turntable Dimension 17.72”x13.78”x5.47”(W x D x H)
Turntable Weight 10.8 lbs
Replacement Needle Crosley NP5
Needle Pressure 3.5+0.5g
Anti-Skate 0~4
Note:
•Design and specifications are subject to change without notice.
•To help save power consumption, some models will comply with ERP energy
saving standard. When there is no audio input for 20 minutes, their powers will
automatically cut-off. To turn power back on and resume playing, you will need to
turn off the power and turn it on again.

English
5
Product Description
1. 45 RPM Adapter
2. Turntable Platter
3. Turntable Spindle
4. Strobe Dots
5. Power Knob
6. Start/Stop Button
7. Hinges
8. Spare Headshell Holder
9. Tonearm Counterweight
10.Downforce Scale Dial
11.Anti-Skate Adjustment Dial
12.Tonearm Lift
13.Cue Lever
14.Tonearm Rest
15.Hold Down Clip
16.Tonearm
17.Pitch Control
18.Headshell Locking Ring
19.Headshell
20.Speed Selector
21.Phono/Line Jacks
22.Grounding Terminal
23.Phone/Line Switch
24.Power Jack

English
6
Initial Setup
Essential Setup
1. Place the unit on a flat and level surface. The selected location should be
stable and free from vibration.
2. Install the turntable lid to the hinges.
3. Remove the tie-wrap that is holding the tonearm.
4. Install the turntable platter.
5. Place the slip mat on top of the turntable platter.
6. Insert the Headshell into the socket at the front of the tonearm, and then turn
the Headshell Locking Ring counter-clockwise. As the ring turns, it pulls the
heashell into its seated position.
7. Slide Tonearm Counterweight onto tonearm and twist it lightly onto the rear
shaft of the tonearm.
8. Adjust the counterweight to set proper stylus pressure.
9. Connect AC adaptor to the Power Jack of the unit.
Note: Do not plug the AC power adaptor to power outlet before all the assembly is
completed. Before turning the power on, make sure again all the connection settings
are correct. Always turn off the power when connecting or disconnecting.
Tonearm Counterweight Adjustment for Stylus Pressure
1. Remove the stylus protector from the cartridge and avoid touching the stylus
tip during the adjustment.
2. Release the tonearm Hold Down Clip, gently hold the tonearm and move it
away from the Tonearm Rest. At this point, the tonearm is unbalanced and
free to swing.
3. While gently holding the tonearm, carefully rotate the Counterweight towards
the front of the turntable until the tonearm is horizontally balanced and hovers
freely just above the platter without the stylus touching the platter surface.
4. Return the tonearm to the Tonearm Rest and lock the Hold Down Clip.
5. While holding the counterweight steady without any rotation, rotate carefully
only the Downforce Scale Dial until the “0” on the scale lines up with the
centerline marked along the top of the tonearm.
6. Rotate the counterweight including the downforce scale dial counter-
clockwise (as seen from the front of the turntable) until the scale shows the
recommended pressure value for stylus.
Note: The recommended pressure for the factory-installed cartridge is 3.5+0.5g

English
7
Phono/Line Switch
For increased flexibility of use, this unit has a built-in stereo phono pre-amplifier.
If you prefer to use the phono input of your stereo system or your standalone
phono pre-amplifier, set the Phono/Line switch to the PHONO position.
Otherwise, please set it to LINE position and make connection to the AUX input
or other high-level input on your stereo system.
Stereo System Connection
RCA Jacks
•The RCA Jacks of this unit are shared as both the Phono output jacks and the
Line output jacks. They are determined by the Phono/Line Switch.
•When used as a line output, the jacks output analog line-level signals and
could be connected directly with a pair of active speakers or the appropriate
input of your stereo system. When used as a Phono output, they should be
connected to the phono pre-amp or the phono input of the stereo system.
•The Red plug connects with the Right channel and the White plug connects
with the Left channel.
Note:
−If the Phono/Line switch is set at LINE position but RCA jacks connected to the
stereo system’s phono input, the sound might be distorted due to input overload
and could damage your stereo system.
−If the Phono/Line switch is set at PHONO position but RCA jack connected to the
stereo system’s line input, the volume will be very low due to lacking signal pre-
amplification.
−RCA Jack is not designed to be connected directly to the passive/unpowered
speakers and if it does, the volume will be very low.

English
8
Turntable Operation
1. Turn the Power Knob clockwise to turn on the power.
2. Set the Speed Switch accordingly.
3. Place the record on the turntable. Use the 45 RPM Adapter if necessary.
4. Remove the stylus protector from the stylus assembly.
Note: To avoid stylus damage, make certain the included stylus guard is in place
whenever the turntable is being moved or cleaned.
5. Press the Start/Stop Button to start the turntable platter’s rotation.
6. Release the tonearm Hold Down Clip.
Note: when the turntable is not in use, remember to lock back hold down clip.
7. Use the Cue Lever to lift up the tonearm.
8. Gently move the tonearm over the record where play is desired to begin. Set
the Cue Lever back to the down position, the tonearm will descend slowly
onto the record and begin to playback.
9. When the record is finished playing, use the Cue Lever again to raise the
tonearm and then return it to the Tonearm Rest. Release the lever to let the
tonearm sit back at its rest. To suspend the playback, repeat the same steps.
10.Lock the Hold Down Clip to secure the tonearm.
11.Press the Start/Stop Button again to stop the turntable platter’s rotation. Turn
the Power Knob counter-clockwise to turn off the power.
Anti-skate Adjustment
•A small outward “anti-skating” force can be applied to the tonearm to
compensate for the “skating” force that pulls the arm toward the center of the
record.
•For best performance during normal turntable usage, it is recommended to
set the anti-skate control knob to the same value as indicated by the
downforce scale dial.

English
9
Pitch Control Adjustment
•When the platter is spinning, observe the strobe dots on the edge of the
platter. As illuminated by the light coming from the strobe illuminator, if the
appropriate row of strobe dots appears to be stationary, the platter is spinning
at the precise rated speed.
•If the dots appear to be moving to the right, the platter is spinning below rated
speed; if they appear to be moving to the left, the platter is spinning above
rated speed.
Needle Replacement
Removing Needle
1. Gently pull down the front edge of the needle.
2. Pull needle forward.
3. Pull out and remove.
Installing Needle
1. Position the needle with its tip facing down.
2. Line up the back of the needle with the cartridge.
3. Insert the needle with its front end at a downward angle and gently lift the
front of the needle upward until it snaps into place.

English
10
Cartridge Replacement
1. Before replacement, put the stylus protector back on the stylus to prevent
damage to the stylus during the replacement process.
2. Turn the headshell locking ring clockwise to release the headshell and
remove it from the tonearm.
3. Carefully remove the wire leads from the original cartridge
4. Loosen the two screws on the headshell that are securing the cartridge and
then remove the original cartridge.
5. Mount the new cartridge to the headshell and tighten it lightly. Do not
completely tighten the screws at this moment.
6. Connect the wire leads to the new cartridge’s terminals .The wire lead color
codes are as below:
White Left channel positive (L+)
Blue Left channel negative (L–)
Red Right channel positive (R+)
Green Right channel negative (R-)
7. Install the headshell back to the tonearm and lock the headshell ring.
8. Adjust the cartridge’s position to make sure it is precisely aligned on the
headshell so that the stylus will be tracking parallel to the grooves. Tighten
the screws completely once the perfect alignment is achieved.
Note: For best result, use a cartridge alignment protractor to aid the alignment process.
Turntable Maintenance
1. Do not touch the stylus tip with your fingers. Avoid bumping the stylus on the
turntable mat or a record’s edge.
2. Clean the stylus frequently with a soft brush with a back-to-front motion only.
3. Clean the records to get rid of dust or grease with a record cleaning brush
and record cleaning solution.
4. Clean the turntable lid and turntable cabinet with a slightly damped microfiber
cloth.
Note: Do not use cleanser other that contains alcohol, benzene or any other harsh
chemicals, which might damage the paint and finish of the turntable.
** Crosley offers a product line of different cleaning accessories. Please
ask your retailer or check out our website www.crosleyradio.com for
more cleaning product information.

English
11
Troubleshooting
There is no power
•No power at the power outlet.
•To help save power consumption, some models will comply with ERP energy
saving standard. When there is no audio input for 20 minutes, their powers
will automatically cut-off. To turn power back on and resume playing, turn off
the power and turn it on again.
Power is on, but the platter does not turn
•Turntable mode is not selected.
Turntable is spinning, but there is no sound, or sound not loud enough
•Stylus protector is still on.
•Tonearm is lift up by the lever.
Record sounds too fast or too slow.
•Wrong speed selected for the record.
•Pitch Control is not adjusted correctly.
FCC Statements
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio TV technician for help.