CRP Securities PL7000 User manual

cover page
PL7000
USER MANUAL

REGULATORY COMPLIANCE
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING STATEMENT
You are cautioned that changes or modications not expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
TABLE OF CONTENTS
Introduction 1 Key Butler User Manual 7
Requirement 1 Using only RFID card and no smartphone 8
NFC Compatible Smartphone 1 DIN 9
Mifare Compatible Access Cards 1 Low Battery 9
Administrator and Clients 2 Resetting to Factory Default 10
Status LED 3 Events and Beeps 12
Sensor Area 4 Troubleshooting 13
Battery Cover and Setup Button 4 Specications 14
User Smartphones 5
Install App 5

1PL7000
Introduction
Requirement
Apart from the key, you can use NFC-ready smartphones or contactless
RFID cards to unlock this lock. The built-in NFC module allows the PL7000
to be unlocked with NFC compatible smartphones or MIFARE compatible
contactless RFID cards. This gives users access easier, safer, and more
convenient.
NFC Compatible Smartphone
PL7000 is designed to communicate with NFC interface, so please choose
smartphones which support NFC function to be a client or an administrator.
MIFARE Compatible Contactless Card
PL7000 can also be unlocked by contactless cards. The cards must be
compatible with MIFARE (13.56Mhz) standards.

2PL7000
Administrator & Clients
An NFC-ready smartphone with a Key Butler app installed, or a contactless
RFID card, is called a USER. For a USER to unlock a lock, it must become
a registerd USER of the lock. Only registered USERS can unlock the lock.
There are two types of USERS. The rst one is the Administrator. A lock
can only have one Administrator at a time. Besides unlocking, the Admin-
istrator is also responsible for managing the lock and all the registered Cli-
ents. Only smartphones can be used as Administrators, RFID cards are
only used as a CLIENT, for unlocking. An Administrator can manage mul-
tiple locks.
The second type of USER is a Client. A lock can have multiple Clients.
A Client can unlock the lock, but not manage it. Both smartphones and
contactless cards can be used as Clients.

3PL7000
Status LED
The Status LED indicator located on the head of the lock which indicates
the operating status of the lock.
Flashing Red LED
When an INVALID USER tries to unlock, the status LED will ash red, and
will generate an audible warning sequence of beeps*
Flashing Green LED
When a VALID USER tries to unlock, the status LED will ash green, and
a series of audible beeps*will be heard
*Refer to page 15 ‘Events and Beeps’
STATUS LED
SENSOR AREA
KEYWAY
EXTERIOR
Status LED

4PL7000
The battery cover can be removed by
unscrewing the battery cover screw.
Behind the cover is where the setup
button is located.
Near Field Communication (NFC) is a set
of standards for smartphones and similar
devices to establish radio communication with
each other by touching them together or
bringing them into proximity, typically a distance of 10cm (3.9 in) or less.
Different smartphones have different antennas and may not be in the same
location. Make sure to locate the best sensor area for your phone and
RFID cards.
SENSOR AREA
BATTERY
COVER
BATTERY
COVER
SCREW
INTERIOR
BATTERY COVER and SETUP BUTTON
SETUP
BUTTON

5PL7000
All smartphone users must install the “Key Butler” app, whether as an
Administrator or a Client. Make sure you have an internet connection or
you have a data plan in order for you to download and install the free app
from the “Play Store”.
USER SMARTPHONES
INSTALL APP
STEP 1
Open APPS Group
STEP 2
Tap Play Store
STEP 3
Search and choose
KEY BUTLER
STEP 4
Tap INSTALL

6PL7000
INSTALL APP
STEP 5
Read permission and tap ACCEPT
STEP 6
Tap OPEN to start APP

7PL7000
KEY BUTLER USER MANUAL
OPENING USER MANUAL
Tap the settings icon
TAP
User Manual option
or check the website:
http://www.keybutlerapp.com/manual.html

8PL7000
USING ONLY RFID AND NO SMARTPHONE
In cases where smartphones will not be used to open the lock and only
RFID cards, you can use the BATCH mode to ADD and DELETE cards.
SETUP BUTTON
1. Push the SETUP BUTTON in the battery compartment
2. Tap the RFID card in front of the lock, when the ascending beep is heard the card is
registered as a user of the lock. All original clients will be deleted and the administrator
will be deleted as well.
SET UP BUTTON MODES
Push for 1 second
ADD users, but ADMINISTRATOR
will be DELETED if already setup
Push for 5 seconds
ADD users, but existing USERS
and ADMINISTRATOR will be
DELETED if already setup
3. Multiple cards can be enrolled, one after the other until the
setup button is pressed, otherwise enrollment will terminate
when the lock times out after a few seconds of inactivity.
4. There are 2 BATCH SET UP MODES
4.1 Push setup button for 1 second to add tapped rd cards
and delete existing ADMINISTRATOR
4.2 Push setup button for 5 seconds to add tapped rd cards
and delete existing administrator users

9PL7000
DIN
The PL7000 comes with a default DIN which is all lower case “pl7000”.
This DIN number is needed when pairing a new lock to a smartphone for
the rst time as an administrator.
LOW BATTERY
The PL7000 has a low battery warning function that can be seen everytime
a phone is used to unlock it.
When the battery is at a low state, there are two distinguishing sound that
are emitted:
1. During successful unlock, the sound is 1 beep then 10 beeps
for low battery warning
2. During failed unlock, the sound is same as an invalid user
unlock tone.

10 PL7000
RESETTING TO FACTORY DEFAULT
To reset the lock to factory setting, do the following steps:
STEP 1
Remove battery cover and take out one battery.
STEP 2
Keep SETUP BUTTON pressed
SETUP BUTTON

11 PL7000
STEP 3
Replace the battery while pressing the setup button
STEP 4
Wait for 4 beeps then release the setup button. The lock will be reset to
factory setting and all previously created users and administrator will be
removed. Replace the battery cover.

12 PL7000
EVENTS AND BEEPS
EVENTS BEEPS
Phone or Card swipe 3 ascending tone beep
Low Battery, Successful Unlock 1 beep, 10 beeps for low battery
warning
Phone or Card Unlock Fail 1 long and 4 short beeps, the long
beep tone is higher
Low Battery, Unlock Fail 1 long and 4 short beeps, the long
beep tone is higher
ADD User Successful 4 beeps ascending tone scale
ADMIN pairing Successful 4 beeps ascending tone scale
COMMUNICATION Issue 2 low pitch scale
Pushing SETUP Button 2 short beeps
Exiting SETUP Mode 2 short and 1 long beep
• When a USER tries unsuccessfully for 3 consecutive tries, the lock will
emit 10 beeps and be in TIMEOUT mode for two minutes

13 PL7000
TROUBLESHOOTING
PROBLEM SOLUTION
Lock not responding Change batteries and try again
Lock is working but no audible
sound
If unlocking function is normal, but
no sound can be heard from the
lock, check if parameter setting
is in MUTE mode. Check “LOCK
CONFIGURATION” of Key Butler
user manual parameter setting
Administrator phone becomes an
invalid user
An Administrator may lose admin-
istration rights when any of the
following happened:
1. Another phone was setup as an
administrator.
2. BATCH Mode 1-sec or 5-sec
options were used that caused the
administrator to be removed from
the lock memory.
3. The lock was reset to factory set

14 PL7000
SPECIFICATION
COMMUNICATION
Type : NFC (Near Field Communication)
Radio Frequency : 13.56 Mhz
DISCLAIMER: Cal-Royal Products does not claim that this lock can provide complete security by itself. This
lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property like any
other locks. No lock can substitute for vigilance, awareness of your environment, and common sense.
Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance
security and reduce risk, you should consult a qualied locksmith or other security professional.
Notice of Open Source Licenses
[FreeRTOS]
This product uses FreeRTOS v7.3.0. The source code of FreeRTOS used can be downloaded here:
http://sourceforge.net/projects/freertos/les/
[OpenSSL]
This product uses OpenSSL, and the OpenSSL license can be downloaded here:
http://www.openssl.org/source/license.html
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)
This product includes cryptographic software written by Eric Young ([email protected]).
This product includes software written by Tim Hudson ([email protected]).