CT CCT-2212BTFX User manual

Trademarks
CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revise without prior
notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright ©Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in
part, in any way whatsoever unless prior consent has been
obtained from Connection Technology Systems Inc.
FCC Warning
The CCT-2212BTFX has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These standards
are designed to provide reasonable protection against
harmful interference when this device is operated in a
commercial environment. This devices generate, use,
and can radiate radio frequency energy and may cause
harmful interference to radio communications unless
installed in accordance with this User’s Guide. Operation
of this device in a residential area is likely to cause
harmful interference in which cases the user is
responsible for taking appropriate remedial action at his /
her own expense.
CE Mark Warning
This is class A products. In a domestic environment this
product may cause radio interference in which case the
user will need to consider adequate preventative
methods.
Checklist
The carton should contain following items:
⎯CCT-2212BTFX Converter
⎯User’s guide
Please notify your sales representative immediately if any
items are missing or damaged.
1. Overview
CCT-2212BTFX is designed to meet the emerging network
deployment needs. This cost effective solution allows user
to extend their network distance up to 100KM via optical
fiber.
Beside a traditional converter, CCT-2212BTFX had built-in
monitoring & self-diagnostic functions to guarantee the
operation. These smart monitoring functions allow user to
maintain and diagnose their critical fiber network more
efficiently.
CCT-2212BTFXis fully compliant with IEEE 802.3, 802.3u
standards. Installation and operation procedures are
simple and straightforward. Operation status and Smart
Monitor may be monitored through the LED or the Buzzer.
Feature and Benefits
- 10/100Base-TX to 100BASE-FX Converter
- Comply to IEEE 802.3, 802.3u
- Interface: 1 * RJ-45 connector
1 * SC Duplex connector
- MDI/MDIX Auto-Crossover supported
-Support Remote Look Back Diagnostic
- Support local and remote status monitor: fiber link
status monitor and testing mode status
- Support Diagnostic testing
3. Installation
•Remove Converter Chassis front panel protective
plate from the selected installation slot.
•Carefully slide converter module into Converter
Chassis and ensure converter golden finger
connection with socket, and rotate CCT-2212BTFX
bracket screw into Converter Chassis
•Attach fiber cable from the CCT-2212BTFX to the
fiber network. The fiber connections must be
matched – transmit socket to receive socket.
•Attach a UTP cable from the 10/100Base-TX
network to the RJ-45 port on the CCT-2212BTFX
•Check Power LED lights up. The TP Link and FX
Link LED will also light up when all the cable
connections are satisfactory.
Fiber
Transceiver
X
10/100Base
-
TX
Network
Fiber
Network
TX
RX
RX
TX
Fig. 2 Basic Network Connection
10/100Bas e
-TX
T
FX
FDX/
COL Speed
RJ-45
Connector
StatusPWR .
Diag

4. LED Description
LED Color Function
Power Green Lit when power is available
TX/Link
ACT Green Lit when TP cable connection with
remote device is good
FX/Link
ACT Green Lit when Fiber cable connection with
remote device is good
FDX/COL Green Lit when TP work in Full Duplex
mode
Lit when Local or Remote Fiber
link O.K.
Green
Blinking when testing success
Status
Lit under below condition:
Remote/ Local FX/TX port link down
Connect device not TS-1000
Orange
Blinking when testing failure
Speed Green Lit when TP link in 100M;otherwise is
10M
5. Technical Specifications
Standards : IEEE 802.3, 802.3u
Interface: 1 X RJ45 connector
1 X SC Duplex connector
Diagnostic LED: Power, TX/Link ACT, FX/Link ACT
FDX/COL, Status
Power Consumption 3.5W
Shipping Weight 0.3 kg
Dimensions: 119mm(W)×86mm(D)×25 mm(H)
Temperature : Operating: 0 ~ 50 oC
Storage: -20 ~ 60 oC
Humidity: 5% ~ 90% RH
Emission: EMI: FCC/CE Class A
For Further reports, please contact us for update
UTP Cat. 5 UTP cable
Fiber 50/125, 62.5/125, or 100/140
µ
m multimode
8.3/125, 8.7/125, 9/125 or 10/125
µ
m single-mode
6. DIP Switch
Pin 1 Off/On TP Auto-negotiation Disable/Enable
Pin 2 Off/On TP Speed 10M/100M
Pin 3 Off/On TP Duplex Half /Full
Pin 4 Off/On Flow control Disable/Enable
Pin 5 Off/On MDIX/MDI mode Force/Auto
Pin 6 Off/On MDI/MDIX
Note: Pin 5 is mutual exclusive with Pin 6, while Pin 5 set
off, pin6 can manual set MDI/MDIX when off/on. If Pin 5
set on (auto mode) then pin 6 useless
Default Setting
Pin1 Pin2 Pin3 Pin4 Pin5 Pin6
On On On On On On
Please perform Power On reset after modify the Dip
Switch setting
7. Fiber Optic Information
Fiber Optic Detail:
Multi-mode
CCT-2212BTFC : SC/1310nm/2Km
CCT-2212BTFT : ST/1310nm/2Km
Single-mode
CCT-2212BTFC (SM-30): SC/1310nm/30Km
CCT-2212BTFC (SM-50): SC/1310nm/50Km
CCT-2212BTFC (SM-80): SC/1310nm/80Km
CCT-2212BTFC (SM-100): SC/1550nm DFB /100Km
Our Address
Connection Technology Systems Inc
18F-6, No.79, Sec.1, Hsin Tai Wu Rd.,
Hsichih, Taipei Hsien, Taiwan, R.O.C.
Tel + 886 2 2698 9661
Fax + 886 2 2698 9662
E-mail [e-mail]
ON
OFF
Fiber
Tranceiver
Dip Switch
RJ-45 Connector
CCT-2212BTFX
10/100Base-TX TO 100Base-Fx
Smart Diagnostic
Media Converter
User’s Guide
V 1.7