Cub Cadet 8454 User manual

8
84 45 54 4 S SE ER RV VI IC CE E M MA AN NU UA AL L
MTD Products, LLC Product Training and Education Department
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983
FORM NUMBER 769-00903

www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CONTENTS
CHAPTER 1. GENERAL INFORMATION ........................................................................................1-1
1. TRACTOR VIEW............................................................................................................................................... 1-3
2. TIGHTENING TORQUE FOR STANDARD BOLTSAND NUTS ................................................................. 1-4
2.1 TIGHTENING TORQUE........................................................................................................................ 1-4
3. SPECIFICATIONS ............................................................................................................................................ 1-6
4. IDENTIFICATIONS........................................................................................................................................... 1-8
4.1 ENGINE NUMBER ................................................................................................................................ 1-8
4.2 SERIAL NUMBER OF THE TRACTOR ............................................................................................... 1-8
5. CAUTION BEFORE REPAIR .......................................................................................................................... 1-9
5.1 BEFORE REPAIR OR INSPECTION .................................................................................................. 1-9
5.2 ASSEMBLYAND DISASSEMBLY......................................................................................................... 1-9
5.3 PARTS TO BE REPLACED .................................................................................................................. 1-9
5.4 PARTS..................................................................................................................................................... 1-9
5.5 ASBESTOS PARTS .............................................................................................................................1-10
5.6 ELECTRICAL SYSTEM.......................................................................................................................1-10
5.7 TUBES AND RUBBERS ..................................................................................................................... 1-11
5.8 LUBRICANT......................................................................................................................................... 1-11
6.REGULAR CHECK LIST...............................................................................................................................1-12
7. OIL & WATER SUPPLY LIST ........................................................................................................................1-13
CHAPTER 2. ENGINE ........................................................................................................................2-1
1. GENERAL ......................................................................................................................................................... 2-3
1.1 APPEARANCE....................................................................................................................................... 2-3
1.2 SPECIFICATIONS ................................................................................................................................. 2-4
1.3 PERFORMANCE CURVE..................................................................................................................... 2-5
1.4 DIMENSIONS......................................................................................................................................... 2-6
1.5 GENERAL WARNING........................................................................................................................... 2-6
2. STRUCTURE AND FUNCTION ..................................................................................................................... 2-7
2.1 BODY ...................................................................................................................................................... 2-7
2.2 LUBRICATION SYSTEM..................................................................................................................... 2-11
2.3 COOLING SYSTEM.............................................................................................................................2-13
2.4 FUEL SYSTEM..................................................................................................................................... 2-15
2.5 INTAKEAND EXHAUSTSYSTEM...................................................................................................... 2-22
3. DISASSEMBLINGAND SERVICING ..........................................................................................................2-24
3.1 TROUBLIE SHOOTING......................................................................................................................2-24
3.2 SERVICING SPECIFICATIONS.........................................................................................................2-27
3.3 CHECKING, DISASSEMBLINGAND SERVICING..........................................................................2-33
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CHAPTER 3. CLUTCH .......................................................................................................................3-1
1.TROUBLE SHOOTING.................................................................................................................................... 3-3
2.SPECIFICATIONS,TIGHTENING TORQUESAND SPECIAL TOOLS ...................................................... 3-4
2.1 SPECIFICATIONS ................................................................................................................................. 3-4
2.2 TIGHTENING TORQUES ..................................................................................................................... 3-4
2.3 SPECIAL TOOLS................................................................................................................................... 3-4
3. STRUCTURE AND OPERATION ................................................................................................................... 3-5
3.1 FEATURES ............................................................................................................................................. 3-5
3.2 STRUCTURE......................................................................................................................................... 3-5
3.3 OPERATION ........................................................................................................................................... 3-6
4. PREPARATION STAGE FOR DISASSEMBLINGANDASSEMBLING........................................................ 3-7
4.1 SEPARATING PANELFRAMEASSEMBLY ......................................................................................... 3-7
4.2 SEPARATING ENGINE AND CLUTCH HOUSING CASE................................................................. 3-9
4.3 DISASSEMBLY..................................................................................................................................... 3-10
5. ADJUSTMENT OF PEDALS ......................................................................................................................... 3-11
5.1 DEFLECTION OF CLUTCH PEDAL................................................................................................. 3-11
5.2 CLEARANCE BETWEEN SAFETY STARTING SWITCHAND LINK............................................. 3-11
6. INSPECTION AND REPAIR.......................................................................................................................... 3-12
6.1 WEARAND DAMAGE ON CLUTCH DISC ....................................................................................... 3-12
6.2 CLEARANCE BETWEEN SPLINE BOSS OF THE CLUTCH DISC AND
SHUTTLE SHAFT SPLINES.............................................................................................................. 3-12
6.3 FLATNESS OF CLUTCH PRESSURE PLATE, DAMAGES............................................................3-13
6.4 DAMAGES TO FLYWHEEL,ADJUSTMENT OF RELEASE BEARING.......................................... 3-13
6.5 WEAR OR DAMAGES ON RELEASE BEARING, RELEASE FORKAND RELEASE HUB ........ 3-13
6.6 CLEARANCE BETWEEN CLUTCH PEDAL SHAFT AND CLUTCH PEDAL BUSHING ............3-14
CHAPTER 4. TRANSMISSION SYSTEM ........................................................................................4-1
1. TROUBLESHOOTING..................................................................................................................................... 4-3
1.1 TROUBLESHOOTING FOR SHUTTLE SHIFT IN OPERATION ERROR ...................................... 4-3
1.2 TROUBLESHOOTING FOR MAIN SHIFTS IN OPERATION ERROR ............................................ 4-3
1.3 TROUBLESHOOTING FORAUXILIARYAND CREEP SHIFTS IN OPERATION ERROR........... 4-4
1.4 TROUBLESHOOTING FOR REAR DIFFERENTIALGEAR IN OPERATION ERROR ................. 4-4
1.5 TROUBLESHOOTING FOR REAR DIFFERENTIAL IN OPERATION ERROR ............................. 4-4
1.6 TROUBLESHOOTING FOR FRONT WHEEL DRIVE IN OPERATION ERROR ........................... 4-5
1.7 TROUBLESHOOTING FOR PTO CLUTCH IN OPERATION ERROR ........................................... 4-5
1.8 TROUBLESHOOTING FOR PTO IN OPERATION ERROR............................................................. 4-5
1.9 TROUBLESHOOTING FOR PARKING BRAKE IN OPERATION ERROR...................................... 4-5
2. SPECIFICATIONS ............................................................................................................................................ 4-6
2.1 TIGHTENING TORQUES ..................................................................................................................... 4-6
3. STRUCTURE ................................................................................................................................................... 4-7
3.1 POWER TRAIN DIAGRAM.................................................................................................................... 4-7
3.2 STRUCTURE......................................................................................................................................... 4-8
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

3.3POWER TRAIN ...................................................................................................................................... 4-9
3.3.1 TRANSMISSION......................................................................................................................... 4-9
3.3.2 SHUTTLE SHIFT SECTION ................................................................................................... 4-10
3.3.3 MAIN SHIFT .............................................................................................................................. 4-11
3.3.4 AUXILIARY SHIFT....................................................................................................................4-12
3.3.5 FRONT WHEEL DRIVE...........................................................................................................4-12
3.3.6 PTO SHIFT................................................................................................................................4-13
3.4OPERATION.........................................................................................................................................4-14
3.4.1 FEATURES.................................................................................................................................4-14
4.PREPARATION STAGE FOR DISASSEMBLINGANDASSEMBLING TRANSMISSION........................4-22
4.1 DRAINING THE TRANSMISSION FLUID.........................................................................................4-22
4.2SEPARATING PANELFRAMEASSEMBLY.......................................................................................4-23
4.3SEPARATING REAR FENDERSAND PLATFORM ASSEMBLY.....................................................4-25
5.TODISMANTLE AND TOASSEMBLE.........................................................................................................4-28
5.1 STANDARDTABLE FOR REPAIR .....................................................................................................4-28
5.2TODISMANTLEANDTOASSEMBLE...............................................................................................4-28
6.DIFFERENTIAL GEAR...................................................................................................................................4-55
6.1STRUCTURE.......................................................................................................................................4-55
6.2OPERATION.........................................................................................................................................4-56
6.3 LOCKING OF THE DIFFERENTIAL GEAR...................................................................................... 4-57
CHAPTER 5. FRONT AXLE...............................................................................................................5-1
1.TROUBLESHOOTING..................................................................................................................................... 5-3
2.SPECIFICATIONS............................................................................................................................................ 5-4
3.STRUCTURE ................................................................................................................................................... 5-6
3.1OPERATION........................................................................................................................................... 5-6
3.2 FRONT WHEELALIGNMENT.............................................................................................................. 5-7
3.3TOE-INADJUSTMENT.......................................................................................................................... 5-8
3.4 DIRECTION CONTROL ANGLE FOR THE FRONT WHEEL .......................................................... 5-8
3.5 ROCKING FORCE OF THE FRONTAXLE, DEFLECTION IN FRONT & REAR DIRECTIONS..5-9
4.PREPARATION STAGE FOR DISASSEMBLINGAND ASSEMBLING...................................................... 5-10
4.1SEPARATING FRONTAXLE..............................................................................................................5-10
5. TO DISMANTLEAND TOASSEMBLE ......................................................................................................... 5-12
5.1 FRONTAXLE CASEAND FRONTAXLE...........................................................................................5-12
5.2 BEVELGEAR CASEAND FRONTAXLE CASE .............................................................................. 5-13
5.3 BEVELGEAR CASEAND FRONT AXLE SUPPORT......................................................................5-14
5.4 FRONTAXLE SUPPORTAND DIFFERENTIAL GEAR CASE .......................................................5-15
5.5 FRONT DIFFERENTIAL GEAR .........................................................................................................5-16
5.6 FRONT BRACKET .............................................................................................................................. 5-19
5.7 REAR BRACKET .................................................................................................................................5-20
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CHAPTER 6. HYDRAULIC SYSTEMS.............................................................................................6-1
1. HYDRAULIC LIFT SYSTEM............................................................................................................................ 6-3
1.1TROUBLE SHOOTING ......................................................................................................................... 6-5
1.2 SPECIFICATIONS ................................................................................................................................. 6-6
1.3 STRUCTUREAND OPERATION......................................................................................................... 6-9
1.4 PREPARATION STAGE FOR DISASSEMBLINGANDASSEMBLING ...........................................6-25
1.5 DISMANTLEANDASSEMBLING.......................................................................................................6-27
2. PTO CLUTCH VALVE SYSTEM .................................................................................................................. 6-38
2.1 SPECIFICATIONS AND DIAGRAM ....................................................................................................6-38
2.2 STRUCTUREAND OPERATION.......................................................................................................6-39
2.3 ASSEMBLINGAND DISASSEMBLING .............................................................................................6-44
2.4 TO CHECK AND TO REPAIR............................................................................................................. 6-46
3. POWER STEERING SYSTEM ......................................................................................................................6-47
3.1TROUBLE SHOOTING......................................................................................................................... 6-47
3.2 INTRODUCTION .................................................................................................................................6-48
3.3 STRUCTUREAND OPERATION.......................................................................................................6-50
3.4 PREPARATION STAGE FOR DISASSEMBLINGANDASSEMBLING ...........................................6-55
3.5 TO DISMANTLEAND TOASSEMBLE...............................................................................................6-58
4. HYDRAULIC PUMP ....................................................................................................................................... 6-66
4.1 TROUBLESHOOTING ........................................................................................................................6-66
4.2 SPECIFICATIONS ...............................................................................................................................6-66
4.3 STRUCTUREAND OPERATION.......................................................................................................6-67
4.4 TO DISMANTLEAND TOASSEMBLE...............................................................................................6-69
5. HYDRAULIC FILTER..................................................................................................................................... 6-71
5.1 STRUCTUREAND OPERATION.......................................................................................................6-71
6. HYDRAULIC PRESSURE OPERATION PRINCIPLE AND TROUBLE SHOOTING .............................6-73
6.1 COMPOSITION OF HYDRAULIC DEVICE & FLOW DIAGRAM OF HYDRAULIC OIL................6-73
6.2 STEERING DEVICES......................................................................................................................... 6-75
6.3 PTO SYSTEM....................................................................................................................................... 6-77
6.4 HYDRAULIC PRESSURE RISE & FALL DEVICE........................................................................... 6-79
CHAPTER 7. BRAKE..........................................................................................................................7-1
1. TROUBLESHOOTING..................................................................................................................................... 7-3
2. SPECIFICATIONS ............................................................................................................................................ 7-3
3. TIGHTENING TORQUE .................................................................................................................................. 7-4
4. STRUCTURE AND OPERATION ................................................................................................................... 7-5
4.1 STRUCTURE......................................................................................................................................... 7-5
4.2 OPERATION ........................................................................................................................................... 7-7
5. DISASSEMBLINGANDASSEMBLING .......................................................................................................... 7-8
5.1 DRAINING THE TRANSMISSION FLUID........................................................................................... 7-8
5.2 SEPARATING PANELFRAMEASSEMBLY ......................................................................................... 7-9
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

5.3 SEPARATING REAR FENDERSAND PLATFORM ASSEMBLY ..................................................... 7-11
5.4 DISASSEMBLING REARAXLE CASE ..............................................................................................7-14
5.5 DISASSEMBLING BRAKE CASE ...................................................................................................... 7-15
6. ADJUSTMENT OF THE BRAKE...................................................................................................................7-16
7. SERVICING ....................................................................................................................................................7-17
CHAPTER 8 ELECTRIC SYSTEM ....................................................................................................8-1
1. ELECTRONIC INSTRUMENTATION ............................................................................................................. 8-3
1.1 INSTRUMENT GAUGE............................................................................................................................ 8-3
1.2 INDICATORSAND WARNING LIGHTS................................................................................................. 8-4
2. TROUBEL SHOOTING.................................................................................................................................... 8-6
3. SERVICING SPECIFICATIONS ..................................................................................................................... 8-8
4. MECHANISM..................................................................................................................................................... 8-9
4.1 STARTING SYSTEM ................................................................................................................................ 8-9
4.2 CHARGING SYSTEM.............................................................................................................................8-12
4.3 PREHEATING SYSTEM......................................................................................................................... 8-14
4.4 FUSE .......................................................................................................................................................8-15
4.5 GAUGEAND SENSORS .......................................................................................................................8-16
CHAPTER 9. CABIN SYSTEM .........................................................................................................9-1
1. DISASSEMBLYAND ASSEMBLY.................................................................................................................... 9-3
2. HEATER ............................................................................................................................................................ 9-8
2.1 STRUCTURE......................................................................................................................................... 9-8
2.2 DISASSEMBLYAND ASSEMBLY......................................................................................................... 9-8
2.3 HEATER OPERATION DEVICE ........................................................................................................... 9-8
3. AIR CONDITIONER ......................................................................................................................................... 9-9
3.1 AIR CONDITIONER .............................................................................................................................. 9-9
3.2 TROUBLE SHOOTING.......................................................................................................................9-13
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CHAPTER 1
GENERAL INFORMATION
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

GENERALINFORMATION
1-3
D569-W02 May-2003
1. TRACTOR VIEW
569W101A
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CHAPTER 1 8454
1-4 D569-W02 May-2003
2. TIGHTENING TORQUE FOR STANDARD BOLTS AND NUTS
2.1 TIGHTENING TORQUE
Screws, bolts and nuts whose tightening torques are not specified in this workshop manual should be tightened
according to the table below.
A. TIGHTENING TORQUE FOR STANDARD BOLTSAND NUTS
M6
(6 mm, 0.24 in.)
M8
(8 mm, 0.31 in.)
M 10
(10 mm, 0.39 in.)
M 12
(12 mm, 0.47 in.)
M 14
(14 mm, 0.55 in.)
M 16
(16 mm, 0.63 in.)
M 18
(18 mm, 0.71 in.)
M 20
(20 mm, 0.79 in.)
N·m
7.85
~
9.30
17.7
~
20.5
39.2
~
45.0
62.8
~
72.5
108
~
125
167
~
191
245
~
284
334
~
392
Nominal
Diameter
Unit
Kgf·m
0.80
~
0.95
1.8
~
2.1
4.0
~
4.6
6.4
~
7.4
11.0
~
12.8
17.0
~
19.5
25.0
~
29.0
34.0
~
40.0
lbf·ft
5.79
~
6.87
13.0
~
15.2
29.0
~
33.2
46.3
~
53.5
79.6
~
92.5
123
~
141
181
~
210
246
~
289
N·m
9.80
~
11.2
23.6
~
27.4
48.1
~
55.8
77.5
~
90.1
124
~
147
196
~
225
275
~
318
368
~
431
Kgf·m
1.00
~
1.15
2.4
~
2.8
4.9
~
5.7
7.9
~
9.2
12.6
~
15.0
20.0
~
23.0
28.0
~
32.5
37.5
~
44.0
lbf·ft
7.24
~
8.32
17.4
~
20.2
35.5
~
41.2
57.2
~
66.5
91.2
~
108
145
~
166
203
~
235
272
~
318
N·m
12.3
~
14.2
29.4
~
34.3
60.8
~
70.5
103
~
117
167
~
196
260
~
303
343
~
401
490
~
568
Kgf·m
1.25
~
1.45
3.0
~
3.5
6.2
~
7.2
10.5
~
12.0
17.0
~
20.2
26.5
~
31.0
35.0
~
41.0
50.0
~
58.0
lbf·ft
9.1
~
10.5
21.7
~
25.3
44.9
~
52.1
76.0
~
86.8
123
~
144
192
~
224
254
~
297
362
~
420
Grade No grade 4T 7T 9T
* The figures on the table above are indicated the top of screw of bolt.
47 9
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

GENERALINFORMATION
1-5
D569-W02 May-2003
B. TIGHTENING TORQUE FOR STUDS
M8
M10
M12
11.7 to 15.7 N·m
24.5 to 31.4 N·m
34.3 to 49.0 N·m
1.2 to 1.6 kgf·m
2.5 to 3.2 kgf·m
3.4 to 5.0 kgf·m
8.6 to 11.5 lbf·ft
18.0 to 23.1 lbf·ft
25.3 to 36.1 lbf·ft
C. TIGHTENING TORQUE FOR HIGH PRESSURE HOSE UNION NUTS
Hose Size
(Inside Diameter: Inches) 1/8″3/16″1/4″5/16″3/8″1/2″5/8″, 3/4″1″
Screw Size (PF)
Tightening (N·m)
Torque (kgf·m)
(lbf·ft)
1/8″
9.8
1
7.2
1/4″
24.5
2.5
18.0
1/4″
24.5
2.5
18.0
3/8″
49.0
5
36.1
3/8″
49.0
5
36.1
1/2″
58.8
6
43.3
3/4″
117.7
12
86.8
1″
137.3
14
101.2
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CHAPTER 1 8454
3. SPECIFICATION
MODEL
8454
Maximum PTO power
38 HP
Engine GROSS power
45 HP
Engine Model
4A220
Type
Indirect injection, vertical, water-cooled,
4cycle diesel
Number of cylinders
4
Bore and stroke
87 x 92.4 (3.425 x 3.638in.)
Total displacement
2,197
Rated revolution
2,600 RPM
Injection timing
18 before T.D.C.
Injection order 1-3-4-2
Compression ratio 22:01
Lubricating system Forced lubrication by trochoida pump
Cooling system Pressurized radiator, Forced circulation
with water pump
Alternator 12V, 50 AMPS
Weight (Dry) 207 kg (456lb)
Capacities Fuel tank 40 L (10.6 gal.)
Engine crankcase 7.0 L (1.9 gal.)
Engine coolant 8.9 L (2.4 gal.)
Transmission case 34.0 L (9.0 gal.)
Front axle case 8.2 L (2.2 gal.)
Dimensions Overall length (without 3p) 3,073mm (120.9 in.)
(with std.tires) Overall length (with 3p) 3,323mm (130.8 in.)
Overall Length (minimum tread) 1,550mm (61.0 in.)
Overall height (Top of ROPS) 2,235 mm (88.0 in.)
Overall height (Top of CABIN) 2,337 mm (92.0 in.)
Overall height (Top of steering wheel) 1,610 mm (63.3 in.)
Wheelbase 1,820 mm (71.6 in.)
Ground clearance 370 mm (14.5 in.)
Track width Front 1,265 mm (49.8 in)
Rear 1,180 - 1,490mm (46.4 - 58.6 in.)
1-6
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

3. SPECIFICATION CON'T
Drive system Tire size (Std. Tires) Front 9.5 - 16.6
Rear 14.9 - 24.8
Clutch Dry single disc
Steering Hydrostatic steering system
Transmission
Synchronized shuttle
12 forward and 12 reverse speeds
Brake Travel Wet disc type
Parking Connected with the traveling brake
Differential Bevel gear
Hydraulic system Hydraulic lift control system Position, Draft and Mix control
Pump Capacity Main Pump 31.2 L/min (8.2 gal.)
Power steering
pump 18.7 L/min (5.0 gal.)
Three point hitch SAE Category 1 & 2
Maximum lifting capacity
1,800 kg (3,968 lb)
No. of remote control valve ports (option) 2-4
PTO PTO shaft SEA 1 3/8, 6 splines
Revolution (independent PTO) 560 rpm
Min. turning radius ( without Brake) 2,865 mm (112.7 in.)
Traction system Fixed drawer (or swing drawer Option)
Weight (with ROPS) 1,720 kg (3,792 lb)
Traveling speed ( at rated engine speed with Std tires) 0.37 - 24.6 km/h (0.23 - 15.29 mph)
1-7
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CHAPTER 1 8454
1-8 D569-W02 May-2003
4. IDENTIFICATION
4.1 ENGINE NUMBER
Engine number is engraved in the left side of the cylin-
der block as shown in the figure.Engine number fills
the important role of providing it’s record.
4.2 SERIAL NUMBER OF THE
TRACTOR
Serial number of the tractor is stamped on the left side
of the front axle frame as shown in the figure.
569W103A
569W104A
(1) Engine Serial Number
(1) Tractor Serial Number
(2) Transmission Serial Number
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

GENERALINFORMATION
1-9
D569-W02 May-2003
5.CAUTION BEFORE REPAIR
569W106A
569W107A
227W105A
5.1BEFORE REPAIR OR INSPECTION
1.In case of repair or inspection, locate the tractor
on the flat ground and pull the parking brake on.
2.Except for the items to be checked while the en-
gine is running, be sure to stop the engine prior to
the work.
3.When washing parts, use parts washing solvent
for industrial use (avoid using gasoline so to pre-
vent environmental pollution). For the hydraulic
parts, apply designated hydraulic oil in washing.
4.When disassembling and assembling of the hy-
draulic apparatus, pay special attention not to al-
low dust or foreign substance to be attached or
intermixed.
5.2ASSEMBLYAND DISASSEMBLY
To check a failure, try to find out its underlying cause. If
assembly or disassembly is needed, perform the work
in regular sequence as specified in this repair manual.
1.Disassembled parts shall be arranged orderly.
2.Sort out the parts to be replaced from the ones to
be reused.
3.Be sure to use standard bolts and nuts that are
designated.
4.When assembling snap rings or spring pin types,
take care of assembling direction.
5.Split pin shall be spread surely not to escape when
installed.
6.When using sealant (such as gasket bond) on the
assembled surfaces, apply it evenly and consis-
tently in a height of 3 ~ 5 mm (0.12 ~ 0.2 in.) on the
contact surface after removing the old bond and
cleaning the sealing surface with solvent. Apply
sealant on the center of the contact surface for the
space between the bolt holes of the contact
surface, and on the more inner side than the bolt
hole for the bolt area.
5.3PARTS TO BE REPLACED
The following parts should be replaced with new ones
when removed.
(1)Oil Seal
(2)Gasket
(3)Lock Nut
(4)Split Pin
(5)O-Ring
When replacing part only genuine Cub Cadet parts.
5.4 PARTS
7. Finish assembly within 20 minutes after applying
sealant, after that, wait approx. 30 minutes later
before filling with oil.
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983
C C

CHAPTER 1 8454
1-10 D569-W02 May-2003
569W110A
569W109A
569W108A
5.6 ELECTRICAL SYSTEM
1. Check electrical wiring every year for any damage
or short circuit at the connections. In addition, have
your dealer inspection the electric system regularly.
2. Do not modify or reorganize the wiring of the elec-
tric field parts.
3. When disconnecting the battery cable, disconnect
negative cable first, reinstall the positive cable first
when reinstalling.
Disconnect battery negative terminal
4. Remove the connector by pulling the plastic
section, not the wiring.
5. When connecting the connector, insert it until it
snaps.
6. Be sure not to drop sensors and relays which are
fragile.
7. When replacing a broken fuse with a new one, be
sure to use the fuse of capacity as specified.
•Be sure to turn the starting key OFF
when connecting or disconnecting the
cable.
CAUTION
5.5 ASBESTOS PARTS
Since dust out of asbestos fibrous parts is extremely
dangerous to your health, be sure to clean such parts
carefully, do not use compressed air.
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

GENERALINFORMATION
1-11
D569-W02 May-2003
569W112A569W111A
Be cautious of oil or other petroleum products on the
hoses and rubber parts, this may cause damage. When assembling and fixing, apply designated lubri- cant where specified in accordance with this repair
manual.
5.7 TUBES AND RUBBERS 5.8 LUBRICANT
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983

CHAPTER 1 8454
1-12 D569-W02 May-2003
6. REGULAR CHECK LIST
Engine oil change
Engine oil filter cartridge change
Transmission oil change
Hydraulic oil filter change
Front axle oil change
Applying grease
Clutch pedal deflection
Brake pedal deflection
Fan belt tension
Fuel filter element change
Air cleaner element change
Battery electrolyte
Oil pressure fuel pipe’s inlet screw
if loosened
Radiator hose’s inlet bands if
loosened
Fuel pipe change
Radiator hose change
Hydraulic pipe joint change
Steering hose change
Toe-in
Deflection adjustment in front and
rear of the front axle
Direction control section
Bolt, nuts and pins of each part
Battery positive code adjustment &
change
Bleeding water in clutch housing
Check injection nozzle*
1yr 2yr
Indicated Hours By Hour Meter Since
Purchased
80070060050045040035030025020015010050
* Maintenance intervals in basis on the EPA instructions.
Check Items 1500hr
the first
periodically
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983