Cumberland Stove Works MF3600G User manual

INSTALLATION AND OPERATION MANUAL
MF3600G, MF3600S, MF3600B Models
Page 26 800-345-6007
CumberlandStoveWorks.com
NORMAL CARE & MAINTENANCE
CLEANING THE GLASS
When the fire is first started, it will produce some smoke.
The smoke might accumulate on the glass surface. Before
the fire gets hot, open the door and wipe the glass surface
off with a damp rag.
If after constant use, the glass might fill with ash deposits.
You must clean the glass after the glass has cooled down.
Do not touch the surface with your hands.Take a damp rag
and wipe the glass clean. If this does not clean the glass
use any non-abrasive liquid spray.
REMOVAL OF CERAMIC GLASS
Open the door and lift off of hinges. If the door is tight, tap
gently on the bottom of the door with your hand or rubber
hammer. Lay door down on newspaper with glass clips
facing you. Loosen the screws and take off the glass clips.
Remove the broken glass carefully and discard.
Reverse the above procedure for replacing new glass with
new gasket.
FUEL POT REMAINS
The “clinker” is the solid mass that remains unburned in
the burner pot. It contains the inorganic parts of the fuel
and is safe to use as fertilizer or dispose of in a proper
container.
SOOT AND FLY ASH
The products of combustion will contain small particles of fly
ash.The fly ash and soot will collect in the exhaust venting
system and restrict the flow of flue gasses. Incomplete
combustion, such as occurs during startup, shutdown, or
incorrect operation of the parlor stove will lead to some soot
formation which will collect in the exhaust venting system.
The exhaust venting system should be inspected at least
once per month (during heavy use) to determine if cleaning
is necessary. Corn has a high ash content.
DISPOSAL OF ASHES
Ashes should be placed in a metal container with a
tight fitting lid. The closed container of ashes should
be placed on a noncombustible floor or on the ground,
well away from all combustible materials, pending final
disposal. If the ashes are disposed of by burial in soil
or otherwise locally dispersed, they should be retained
in the closed container until all cinders have been
thoroughly cooled.
EXHAUST AND CONVECTION AIR FILTER
• Remove air filter and replace regularly
• Clean exhaust vent
Ash Pan Location
CAUTION
DO NOT OPERATE STOVE WITH BROKEN GLASS.
DO NOT SLAM THE DOOR SHUT.
DO NOT STRIKE GLASS.
DO NOT USE ABRASIVE CLEANERS.
DO NOT CLEAN HOT GLASS.
REPLACE CERAMIC GLASS WITH FACTORY
AUTHORIZED REPLACEMENT PARTS ONLY.
THE CLINKER WILL REMAIN HOT FOR SEVERAL
MINUTES AFTER IT IS PULLED OUT OF THE BURNER
POT.

INSTALLATION AND OPERATION MANUAL
MF3600G, MF3600S, MF3600B Models
Page 27800-345-6007 CumberlandStoveWorks.com
CAUTION
THIS IS A MINIMUM REQUIREMENT FOR SOOT
AND FLY ASH REMOVAL. ASHES SHOULD BE
PLACED IN A METAL CONTAINER WITH A TIGHT
FITTING LID. THE CONTAINER SHOULD BE PLACED
ON A NON-COMBUSTIBLE FLOOR, WELL AWAY
FROM COMBUSTIBLE MATERIALS, PENDING FINAL
DISPOSAL. IF ASHES ARE DISPOSED OF BY BURIAL
IN SOIL OR OTHERWISE LOCALLY DISPERSED, THEY
SHOULD BE RETAINED IN THE CLOSED CONTAINER
UNTIL ALL CINDERS ARE NO LONGER WARM.
DAILY MAINTENANCE
The surfaces of the stove may be hot. Always wear
protective gloves even when the stove is cool to the touch.
There are two areas that require daily maintenance; (1) the
firebox and (2) the fire pot.
• Remove the top baffle inside the firebox and clean
the fly ash and soot on all exposed parts using a steel
brush and ash cleaning vacuum.The use of a shop-vac
is not recommended. Talk to any authorized dealer for
information about an ash cleaning vacuum.
• The fire pot and the area around it are cleaned using the
special tool provided with the stove and an ash cleaning
vacuum. It is important to remove any unburned pellets
that may have fallen behind the burn pot.
• Complete the daily maintenance by checking the seal
on the doors. Look for pellets that may have been left
behind during loading. Check that each of the door seals
are flush with the stove and sealing properly.
WEEKLY MAINTENANCE
• To clean fire pot with cleaning tool, remove fire pot by
unscrewing the small spring from the lower cleaning
rod. Remove rod and pull out fire pot. Hang on to end
of cleaning tool with the hole in it. Scrape the fly ash
that has fallen through the holes of the plate in the gap
that sits below the fire pot.
• Remove the ash pan and dump the ash into a metal
container.
• Cleaning of the exhaust system will depend upon the
ash and debris content of your fuel. If your fuel has a high
ash content and/or significant debris in it, the exhaust
system will require weekly cleaning. Cleaner fuels will
allow for monthly cleaning of the exhaust system. If you
have installed clean out tees you will need to check for
cleanliness.
NOTE: A clean unit burns efficiently and will remain
trouble free!
SEASONAL CLEANING
Once every year you must clean out all of the fuel in the
hopper, firebox area, ash pan and fire pot area. Corn and
any ash can accumulate moisture over the summer months
causing the unit to rust and the fuel to mold.
It is recommended that prior to shutting down the unit in
the spring it is run on the high setting for about six hours to
help clean out the heat exchanger system, venting system
and firebox area.
AIR FILTER
Air Filter Placement - back view
WARNING
WHEN PERFORMING ANY INTERNAL ELECTRICAL
MAINTENANCE
• MOVING PARTS INSIDE OF THE CABINET MAY
CAUSE INJURY. DO NOT OPERATE UNIT WITH
PANELS REMOVED OR OPEN.
• HOT PARTS. DO NOT OPERATE THE UNIT WITH
PANEL OPEN.
• RISK OF ELECTRIC SHOCK. DISCONNECT POWER
BEFORE SERVICING UNIT.
• INTHE EVENT OF COMPONENT FAILURE, REPLACE
WITH THE ORIGINAL FACTORY EQUIPMENT.