Cura1 iBeam 2721 User manual

2721 .
Optional Accessories (Sold Seperately)
2723 EzyStand, 3501 ActiveCare Pager,
2700 Six Channel Cordless Falls Monitor, 3500
ActiveCare Console, 2544 Cordless Multiport Expander,
2544 Cordless Multiport Expander Bracket Mount,
2404 Plug Pack
The 2721 iBeam has a narrow detection beam
which detects movement up to 3m away, and a
wireless range of approx. 30m*. Use in
bedrooms, doorways, near stairs etc.
The narrow beam is especially useful if you
have other people in the same room who do
not require movement detection or where only
a very specific area requires monitoring.
*The range of wireless devices may vary and be dependent on your
specific environmental conditions.
Optional 2723 EzyStand
Tightening Nut
Cable Clips
Height
Adjustment
Lock
Magnet
2404 AC Adapter
(Optional)
Back View
2721 iBeam
Screws
(supplied)
Double
sided tape
(supplied)
Mounting hardware
Mounting tape and
screws are supplied if
you wish to
permanently mount
the iBeam to a fixture.
iBeam Bracket
Front View
ON OFF Switch
LED illuminates
green when
motion detected.
iBeam curtain
window.
Antenna.
Extend fully
when in use.
Side View
Adjustable tilt can
be used when the
iBeam is located on
the ground or up
high.
1. Rotate the
iBeam in it’s
bracket 90 degrees
so that it is facing
the ceiling.
2. Apply gentle
pressure to one
arm of the
bracket so that
the iBeam can
easily pop out.
If you use screws to fix the iBeam bracket to a permanent
position, you will need to separate the iBeam and bracket
before you screw the bracket to a fixture.
To easily separate the iBeam from it’s bracket:
Detatching the iBeam from it’s mounting bracket
UM-028c

1
QUICK START GUIDE
2721
Step
Insert 3 x AA alkaline batteries and / or
connect the 2404 Plug Pack.
Ensure the iBeam’s ON / OFF switch is in the OFF
position.
Release the battery compartment cover by pressing the
compartment latch to the right and allowing it to lever
open.
Insert 3 x AA batteries.
Connect a 2404 Plug Pack (optional) to the power
socket on the back.
2
3
Step
Optional Mounting
The 2721 iBeam can be paired with the following cura1devices:
Step
Pair the iBeam with a receiving device.
The 2721 iBeam has an extremely narrow detection beam
allowing it to be positioned so that the detection area is very
precise.
Use in bedrooms, doorways, near stairs etc. Some positioning
suggestions are depicted below.
Turn on the iBeam and be sure to thoroughly test before use.
The LED illuminates green when movement is detected.
IMPORTANT - When testing, please wait 15 seconds
between activations. After the it detects movement, the iBeam
is disabled for approximately 10-15 seconds before it can detect
movement again. This is to conserve battery life in busy
environments.
4
Step
Position iBeam for desired detection area.
Back View
While the 2721 iBeam can be used free-standing on a bedside
table, or on the floor next to a bed, chair or door, it can also be
fixed in position with the included mounting adhesive pads and /
or the included screws. PTO for information about securing the
iBeam to a fixture.
An optional EzyStand is also available which provides a sturdy,
height-adjustable base that can be repositioned as needed.
With the iBeam within range of the receiving device, put the
receiving device into Programming Mode (for instructions please
refer to the documentation that came with the receiving device).
To pair the iBeam with the receiving device, extend the antenna
fully and turn the ON / OFF switch from OFF to ON.
The iBeam should now be paired with the receiving device.
Now turn OFF the iBeam while completing any further
programming for other devices (if needed).
3500
ActiveCare
Console
3501
ActiveCare
Pager
2700 Six
Channel Cord-
less Falls Monitor
2544 Cordless
Multiport Expander
(also 2549)
Push in to release
battery compartment
cover.
2404 Plug Pack