Current Audio 4PS Troubleshooting guide

The 4PS Four Pair manual Stereo Speaker Selector is a
self contained passive selector box. It allows the user to
control up to 4 separate pairs of stereo speakers from one
amplifier without an expensive electronic distribution
system. It requires no external power to operate.
The 4PS is used for multiroom stereo sound systems. With
the 4PS the user can selectively turn ON or OFF any one of
four zones. The unit has a built-in impedance
compensating network to prevent overload to the amplifier.
Unlike others on the market, no switch is required to
activate the protection circuit. The protection circuit is
always On.
Each spring loaded connector can handle up to a 14 gauge
wire. There is a Red/Black connector pair for each speaker,
and one set ( Right and Left) for the amplifier source input.
The speakers are arranged in 4 zones. Make sure the
polarity is observed. You can hook-up one, two, three or
four pairs of speakers.
Once the 4PS is properly hooked-up operation is
straightforward. Select a Zone or any combination of Zones
and press the corresponding button for that Zone. The
button will be indented to indicate ON. Push again and it
will release and indicate OFF. For example press buttons
#1 and #3 to listen to music in Zones #1 and #3. The
buttons that are out indicate OFF and no sound will be
heard from that Zone.
With our limited 5 year warranty you are assured years of
superior trouble free operation.
Four Pair
Manual Stereo Speaker Selector
4PS Stereo Speaker Selector User’s Installation Guide
Part Number 93027 Model # 4PS
Manual URL www.currentaudio.com
Accessories Any 8 Ohm Speaker
www.currentaudio.com
©2011 Current Audio LLC
1830 John Towers Avenue El Cajon, CA 92020 Sales 866-927-7181
Specifications subject to change without notice. 4PS RPA 082211
4PS Front View
4PS Rear View
4PS Speaker Selector
Specifications
Height
2“ (50mm)
Width
8 5/8“ (216mm)
Depth
4.4 “ (112mm)
Weight
1.8 lbs
Max Wire Gauge
#14
Impedance Per Speaker
8 ohms
Warranty
Limited 5 Year
Max Power Per Speaker @ 8 ohms
40 Watts RMS

4PS Stereo Speaker Selector User’s Installation Guide
Specifications subject to change without notice.
Limited 5 Year Warranty
Current Audio, LLC speakers and accessories are warranted to be free from defects in materials and or workmanship to the original retail
purchaser for a period of 5 years provided the equipment was purchased and installed from a Current Audio, LLC Authorized Dealer.
In the event of defective materials and or workmanship, Current Audio, LLC will, without charge, repair or replace, at its option, the defective
product. In order to make claim under this Warranty and to obtain performance of any obligation under warranty, please contact Current
Audio. Instructions will be given on how to return the defective product to Current Audio. Returned products must be shipped prepaid. Proof of
purchase must be provided with the product.
The Warranty does not apply to damage not resulting from defective materials and or workmanship while in the possession of the original
consumer or due to unreasonable use by the original consumer, which includes but not limited to improper installation, negligence,
unauthorized repair or modification, aesthetic deterioration from the environment. Products purchased by unauthorized sources will void the
warranty and not be honored.
Current Audio, LLC is not liable for any incidental or consequential damages, so the above limitations or inclusion may not apply to you. This
warranty gives you specific legal rights, and you may have other rights, which vary from state to state within the United States.
Installation
The 4PS allows the user to distribute sound to four separate listening areas. See the following diagrams for easy hook-up.
Locate the speaker wire for that speaker. Pull enough wire slack down to attach the 2 conductor wire to the standard
constant tension spring-loaded terminals.
Remove about 2”of the outer jacket then strip about ½” insulation from each wire and slightly twist the strands to ensure
all strands can be inserted into the hole. Refer to the picture for location of the standard constant tension spring-loaded
terminals.
Push down on the RED (+) colored Terminal and insert the Red or copper colored conductor all the way up to the
insulation into the hole at the top of the terminal. Now release your finger from the terminal . Next do the same to the Black
or silver colored conductor and insert into the BLACK (-) colored Terminal. Make sure there are NO whiskers from the
strands that could cause a short. Do the same for the amplifier input source.
Note: Sometimes your wire color may be White (+) and Green (-).
You now have a connection with the proper tension for continued operation that will not wiggle out or cause poor
connection.
To operate Push the desired Zone number button in for On and push again for Off or any combination of buttons.
4PS RPA 082211
Rock Speakers
Strip to ½”
2”
In-Wall Speakers
Patio Speakers In-Ceiling Speakers
Amplifier
R (-)
L (-)
R (+)
L (+)