Custom Brackets CB Gimbal Basic User manual

phone [phone]
website: www.custombrackets.com
email: [email protected]
32 Alpha Park
Cleveland, Ohio 44143
Made in USA
Assembling CB Gimbal
Base
Support plate
Tripod
Base
Upright lock knob
Safety stop
Upright
Lens platform
Arm
Lens platform
lock knob
Safety stop
Upright
Arm lock knob
(must face front)
Arm
Safety stop
Loosen upright lock knob and slide upright
into the base until safety stop rests on
base. Tighten upright lock knob to secure
upright.
We recommend only using a tripod with a
3/8”-16 mounting stud.
Place base on the tripod’s 3/8”-16 mounting
stud and rotate support plate clockwise
until base is rmly attached to tripod. Hand
tighting will be enough to secure the base to
tripod. It is not recommended to use pan
lock to secure support plate to tripod.
* * * * * Caution * * * * *
If you choose to use a tripod with a 1/4”
mounting stud, test tripod to make sure it
will handle the weight of camera and lens
combination. You will need to purchase a
3/8” to 1/4” reducer bushing and install it in
bottom of CB Gimbal’s support plate.
Loosen arm lock knob and slide upright
into Arca Swiss type clamp until safety
stop rests on the clamp. Push in and
tighten arm lock knob to secure arm.
* * * * * Note * * * * *
Arm lock lever incorporates a unique
tighten system that allows the knob to
move freely once tightened.
Loosen lens platform knob and slide lens
platform into arm until it rests on the safety
stop. Tighten lens platform knob to secure
lens platform.
* * * * * Note * * * * *
Final height location of lens platform is
explained in “CB Gimbal Features” on
reverse side.
Install screw(s) into lens plate at the labeled ends. If not, the
screw(s) may be damaged. Some lenes will require that both
screws be in one slot for balancing the lens.
The “D” screws have fold out clips for hand tightening. To
make it tighter, use a straight screwdriver or quarter.
Screw the GLM-1 or GLM-2 to the bottom of your lens foot
using the “D” screws that correspond to the lens mounting
holes.
Do not insert any object as leverage into the “D” clip.
Camera platform
reference lines
Lens plate setup
reference lines
Lenses either have 1/4” or 3/8” threads. (1) 3/8” and (2) 1/4”
screws are included with each lens plate - it is important to use
the correct size.
Assembling CB Gimbal Basic
Attaching lens plate to lens and lens
to CB Gimbal or CB Gimbal Basic
Loosen Arca Swiss clamp of ball head and slide upright into
clamp until safety stop rests on clamp. Tighten clamp to
secure upright.
Safety stop
Upright
Lens platform lock knob
- - Step One - - - - Step Two - -
- - Step Three - - - - Step Four - -
Pan lock
knob
Arca Swiss
type clamp
Ball Head
Customer supplied
Arca Swiss type clamp
Pockets on
this side
Rotate setup lever into arm pocket (see “CB Gimbal Features”
for location on reverse side).
Install lens plate by loosing lens lock knob all the way, then
place lens plate into lens platform. Tighten lens platform lock
knob completely, then loosen 1/2 turn. Slide lens plate forward
or backward to achive balance, then retighten lens platform
lock knob.
Achieving balance is similiar on CB Gimbal Basic.
Mounting holes
CB Gimbal, CB Gimbal Basic, CB Gimbal Upgrade
INSTRUCTIONS

Tilt lock knob
Tilt drag knob
Pan lock knob
Pan drag knob
2 degree markings
Degree indicator line
Bubble level
PAN
TILT
Lens lock lever
Arm lock lever
push in and turn
to lock and unlock
Setup lever
for balancing lens, changing cameras,
and secure travel while on tripod
Upright lock lever
Lens platform
lock lever
For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any defect in material or workmanship. Warranty does not cover repairs due to customer abuse,
negligence, impact or any modications made by the customer. All knobs are installed using “loctite” to prevent them from unscrewing. Hand tightening is sufcient to secure any component and the lens
plate. Excessive force unscrewing will cause the knobs to unscrew and void warranty. Warranty service is available by returning the CB Gimbal or component (shipping prepaid) to Custom Brackets. All
returns must include a return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem, and a copy of the sales receipt.
Repair service is available by returning the CB Gimbal product (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number (contact Custom Brackets to obtain), letter
explaining the problem, and a copy of the sales receipt. A repair cost will be issued and must be approved prior to any repairs. Shipping charges are the responsibility of the customer.
The CB Gimbal product line is designed to be completely maintenance-free. The bearing rotation tension is factory set. Attempting to adjust the tension will void the warranty and may result in damage to
the camera or lens.
USA 5 Year Warranty
Repair
Maintenance
For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any defect in material or workmanship. Warranty does not cover repairs due to customer abuse,
negligence, impact or any modications made by the customer. All knobs are installed using “loctite” to prevent them from unscrewing. Hand tightening is sufcient to secure any component and the lens
plate. Excessive force unscrewing will cause the knobs to unscrew and void warranty. Limitation to the warranty - after year one shipping charges are not covered. Warranty service is available by returning
the CB Gimbal or component (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem, and a
copy of the sales receipt.
International 5 Year Limited Warranty
The CB Gimbal has many unique features found only in our Custom Brackets gimbal line. It is constructed from aircraft aluminum that is “hard anodized” for a lightweight and scratch resistent nish. All knobs
have an ergonomic design and are machined from aluminum to prevent breakage. All of the fasteners are made from stainless steel to resist corrosion. The pan and tilt knobs have a rubberized coating for
comfort, traction, and to resist cold weather. The CB Gimbal has a setup / travel lever that is used for balancing the lens and securing for travel from location to another when the lens is still attached.
CB Gimbal Facts
- - - CB Gimbal Features - - -
* * * * * Note * * * * *
Adjusting the lens center height
For balancing the lens, position the lens
slighty above the center of the tilt axis
(best position is when lens stays in
position without drag or lock)
- - - CB Gimbal Basic Features - - -
TILT
PAN
Tilt lock knob
Tilt drag knob
Lens lock lever
push in and turn
to lock and unlock
Ball Head
Customer supplied
Arca Swiss type clamp
* * * * * Note * * * * *
Use Ball Head for all
panning functions
Center of Tilt Axis
in-line with arm lock lever