Custom Dynamics ProGLOW PG-7-14-B User manual

Questions? Call us at: 1 [phone] M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
02/2021
Package Contents:
- 7” ProGLOW™ LED Headlamp (1)
- H4-TOUR-ADAPTER (1)
- Instructions
Part Number: PG-7-14-B PG-7-14-C
Important: Due to the increased light output from this unit, it is recommended
you take the vehicle to a dealer to have the headlamp properly adjusted. Weight
and tire pressure can affect the position of the light.
Warning: To prevent possible electrical shock, disconnect the negative battery
terminal before installing this product.
ATTENTION
Please read all Information below before Installation
Fits: 2014-2021 Harley-Davidson® Street Glide (FLHX), Street
Glide Special (FLHXS), CVO Street Glide (FLHXSE), Electra Glide
Standard (FLHT), Electra Glide Ultra Classic (FLHTCU), Electra Glide
Ultra Classic Lo (FLHTCUL), Ultra Limited (FLHTK), Ultra Limited Lo
(FLHTKL), CVO Limited (FLHTKSE), Road King (FLHR), Road King
Special (FLHRXS) and CVO Road King (FLHRSE), Tri Glide Ultra
(FLHTCUTG), CVO Tri Glide Ultra (FLHTCUTGSE), Freewheeler
(FLRT) & 1984-2017 FL Softail® models with OEM 7” headlight buck-
ets.
Note: Requires ProGLOW™ Bluetooth Controller (sold separately)
and ProGLOW™ App download for control of color changing halo.
Note: 2014-2021 Road King (FLHR), Road King Special (FLHRXS)
and CVO Road King (FLHRSE) require additional wiring adapter PN
2001-1264 (sold separately).
Fairing Installation:
1. Disconnect the vehicle battery negative [ - ] terminal.
2. Review detailed service manual for instructions on replacing
factory headlamp.
3. Remove the factory headlamp trim ring, retaining ring and
headlamp only.
4. Connect the 7” LED headlamp to the existing factory H4 plug.
Note: 2014 to current Street Glide®, Electra Glide®, Ultra and Tri Glide®
models (Including CVO™): You will need to use the included H4-TOUR-
ADAPTER. If your headlamp’s electrical harness connector does not
match the flat 4 pin connector of the H4-TOUR-ADAPTER, follow your
bike’s harness back into the fairing until you find your bike’s flat 4 pin con-
nector.
5. Install the headlamp, retaining ring, and trim ring. Make sure
no wire or any components of the harnesses can be pinched
during installation and that they will not be exposed.
6. Connect the ProGLOW™ wiring harness to Channel 1 of the
ProGLOW™ Bluetooth Controller. Note: If the Brake Signal
Sync is turned on in the App, The Channel 1 Override will
need to be turned ON as shown in Photo 1.
7. Re-connect vehicle battery negative [ - ] terminal.
8. Test high and low beam functions of headlamp.
9. If the Brake Signal Sync is turned on in the App, test the
Brake Sync Channel 1 Override to ensure the Headlamp halo
does not turn Red when the Brake is applied.
10. Properly Aim the headlamp for maximum performance.
Custom Dynamics® 7” ProGLOW™ LED
Headlamp
Installation Instructions
1
We thank you for purchasing the Custom Dynamics® 7” ProGLOW™ LED headlamp! Our products utilize the
latest technology and high quality components to ensure you the most reliable service. We offer one of the best
warranty programs in the industry and we back our products with excellent customer support, if you have ques-
tions before or during installation of this product please call Custom Dynamics® at 1(800) 382-1388.

Installation Instructions - Page 2
Questions? Call us at: 1 [phone] M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
02/2021
Non-Fairing Installation:
1. Disconnect the vehicle battery negative [ - ] terminal.
2. Review detailed service manual for instructions on replacing factory head-
lamp.
3. Remove the factory headlamp trim ring and headlamp from the headlamp
bucket.
4. Drill a 5/8” hole in the back of the headlight bucket.
5. Route the ProGLOW™ wiring harness through the hole in the headlamp
bucket and install the grommet.
6. Connect the 7” LED headlamp to the existing factory H4 plug.
7. Install headlamp and trim ring on the headlamp bucket.
8. Connect the ProGLOW™ wiring harness to Channel 1 of the ProGLOW™
Bluetooth Controller. Note: If the Brake Signal Sync is turned on in the App,
The Channel 1 Override will need to be turned ON as shown in Photo1.
9. Re-connect vehicle battery negative [ - ] terminal.
10. Test high and low beam functions of headlamp.
11. If the Brake Signal Sync is turned on in the App, test the Brake Sync Chan-
nel 1 Override to ensure the Headlamp halo does not turn Red when the
Brake is applied.
12. Properly Aim the headlamp for maximum performance.
Red
Black
Blue
Using The H4-TOUR-ADAPTER on 2014-2021 H-D™ Touring Models
H4
Plugs
H4-TOUR-ADAPTER
4 Pin
Plugs
Red
Black
Blue
Using The CDTB-H42H9H11 (sold separately). on 2014-2021 H-D™ Road King Models
CDTB-H42H9H11
Adapter Harness
(sold separately).
Black
Blue/Yellow
Black
Blue/White
Headlamp Harness Connectors
Low Beam Connector
High Beam Connector
~
To Channel 1 of the ProGLOW™
Bluetooth Controller
~
To Channel 1 of the ProGLOW™
Bluetooth Controller
ProGLOW™ Wiring Harness
NOTE:
Use caution when connecting the mating
ProGLOW™ accessory connectors, confirm
the mating connector is connected correctly
or damage will occur to the lighting accesso-
ries. The locking tab should slide onto the
lock and lock into position. See Photos be-
low.
LOCKED
ProGLOW™ Wiring Harness
Grommet
H4
Plugs
Grommet