CVW BeamLink-Ultimate User manual

2019.10.10
BeamLink-Ultimate
Full HD
High Definition
Frequency
5GHz
Range
500m
Ultra Low
Latency
4
Channel
Video
Streaming
IP
Intercom*4
EU Environmental Protection
Waste electrical products should not
be disposed with household waste.
Please recycle where facilities exist.
Consult to your local authority or retailer
for recycling advice.
All-in-one Wireless Transmission
Transmitter:7081
Receiver:3060+3081
User Manual
User Manual V1.0
This user manual applies to
:
CVW
professional products

01
01
02
03
07
03
05
07
09
01
About the User Manual
Product Features
Brief Introduction
Packing List
Machanism & Interface
Wireless HD Transmitter 7081
Wireless HD Receiver 3060+3081
Product Installation
Wireless HD Transmitter 7081
Wireless HD Receiver 3060+3081
Contents
Specification
Product Application
Parameters Configuration
16
19
24
27
14
22
29
OLED Display Description
Functional Instructions
Wireless Software Upgrade
Troubleshooting

01 02
BeamLink-Ultimate is an upgraded version of the BeamLink Quad that
adds voice intercom capabilities. It is a set of 4TX-to-1RX full-HD audio
and video wireless transmission system and wireless voice intercom system.
The 4-channel image transmission and voice intercom share one wireless
channel and supports the highest video resolution of 1080P/60Hz. This
system is based on 5G wireless network technology for transmission, along
with advanced 4×4 MIMO and Beam-Forming technology. Image processing
is performed using H.264 technology, and thus the images has higher resolution
and the latency is lower. It is the best companion for the director to shoot,
using advanced VoIP technology, integrated with voice intercom function,
which is clear in voice and easy to carry. The transmitteris CP7081, and the
receiver is the combination of CP3060 and CP3081, which are connected via
a network cable.
About the User Manual
This Manual details the product specifications, instructions for use,
precautions, and troubleshooting. Read the Manual carefully before using
the product. If you have any questions or difficulties in using this product,
contact the company or the seller in time.
Product Features
Brief Introduction
This product supports HD-SDI&3G-SDI input and output as well as HDMI full-HD
input and output, with the highest resolution of 1080P/60Hz. With highest
compress ratio and best video resolution using H.264 technology, and the latency
is as low as 70ms.
4 transmitters and 1 receiver share one wireless channel
High-quality and ultra low latency
This product supports 4 video streams input simultaneously, with resolution
up to 1080P60 per channel. 4 video streams share one wireless channel,
which greatly saves spectrum resources and provides great convenience for
users to perform multi-camera shooting.
* Do not use this product for a long time in the sun or dusty place.
* Be sure to use this product within the temperature and humidity ranges.
Do not operate the product under vibration or strong magnetic fields.*
* Do not put conductive materials in the product vents.
* Do not open the product yourself without the guidance of our professionals.
* Before power-on, make sure that the adapter input voltage is AC110V-220V,
and that the output voltage and current meet the product specifications.
* Before power-on, make sure that the antennas are installed.
* This product is a 5GHz WIFI device. When there are devices with the same
frequency around, there may be mutual interference. In this case,
solve the problem by switching the frequency channel of the product.
Special Precautions
The RS232 and Tally function interfaces of this product are non-standard
physical interfaces. If you need this function, communicate with the
sales staff.
Thank you for choosing CVW's professional wireless HD audio
and video transmission product. Read the following precautions
carefully before using this product:
When installing the machine with the double-thread screw supplied with
the product, tighten the product with the fastening screw plate. Do not
hold the machine for rotary tightening to prevent the screw from being
unable to be removed from the machine.

Packing List
The following items are included in the product package
Double Ball Head
Arm Mount
Gooseneck
Microphone
Headphones
*4 pieces
Users can choose single-ear headphones or double-ear headphones
when ordering.
Transmitter
*4 pieces
Antenna
* 16 pieces
RS232 cable
*4 pieces
SDI cable
*4 pieces
Power supply
cable*4 pieces
Receiver
*1 piece
Antenna
* 4 pieces
RS232 cable
*4 pieces
Power adapter
*1 piece
Metal Stand *1 piece
Power adapter
(12V/2A) *1 piece
Headphones
*4 pieces
Receiver
3081 *1 piece
Network cable
*1 pieces
Notice: The transmitter comes with the Sony NP-F type battery dock and has
preassembled V-mount connector. The receiver has preassembled V-
mount battery plate and V-mount connector.
03 04
Beam-Forming
Combined with 4×4 MIMO and Beam-Forming technology, this product has
advantages over other WiFi products in the market in terms of transmission
distance and video resolution. Beam-Forming technology makes wireless signals
more concentrated and stronger in the direction from which they are transmitted
to the receiver, allowing them to transmit farther and be less susceptible to
interference from other signals, thus making them more stable.
Support RS232/422
This product supports transparent transmission device via RS232/422
interface, which is convenient for users to control the remote device through the
local device at the receiving terminal, such as the PTZ.
controlling
This product supports switching between two operating modes, namely standard
mode and RTSP streaming mode. In standard mode, this product supports
4TX-to-1RX, and the video outputs interface are HDMI and 3G-SDI. In RTSP streaming
mode, this product supports 4TX-to-Multiple RX, and the video streaming interface is
LAN port(RJ45) ..
Standard mode and streaming mode
Voice intercom
Each video transmitter and receiver terminal of the product is equipped with a
3.5mm voice intercom interface. One-to-one full-duplex intercom or one-to-many
broadcast can be performed on the transmitter and receiver terminals. The receiver
hands-free call mode is automatically disactived when the headphones are plugged in.
The headphone jack supports the mainstream four-segment 3.5mm mobile phone
headphones on the market.

Function Operation Description
TX: 7081
05 06
BeamLink-U lt im ate
tX
RESET
WPS
LNA ON/OFF
SDI LOOP out
LED
CALL
VOL+
VOL-
MIC/SPK
V-MOUNT
LINE In
RS232/422
HDMI In
Structure & Interface
Antenna Interface
SDI In
OLED Display
DC-IN
Power Switch
Tally out
Transmitter Key Operation
“L” (Low-gain mode):It is suitable for short distance and
complex environment, with strong anti-interference ability.
After switching to “L mode”, "L" letter will be displayed on
OLED screen.
Call request Short press the
CALL”button“ Making call request to director actively.
Short press
the button“+” Increase the volume
Increase the
volume
Decrease the volume
Decrease the
volume
External Audio
Press the
“LNA ON/ OFF”
button for about 6s
The audio signal in the video is from the “LINE IN” interface,
the microphone icon displays beside the transmitter number
on OLED screen.
LED
Solid Yellow
Solid Orange
Blinking in Yellow
High-gain and
low-gain mode
switching
Hold the “LNA
on/off” button
for 3 seconds to
switch the mode.
Code matching
Press the “WPS/
RTSP” button
for about 3s
In the code matching process of the transmitter and
receiver, the word “WPS” will always be displayed on
the OLED display, and the string will disappear after
the code matching complete. The transmitter and
receiver need to be in code matching status at the
same time for code matching.
Standard and
streaming mode
switching
Press the “WPS
” button
for about 6s
/
RTSP
When switching to streaming mode, the word “RTSP”
will be displayed on the OLED display, and the
product will enter streaming mode.
Reset the
encoding board
Press the
“RESET” button
for about 3s
During the reset of the encoding board, the
“RESET” string will always be displayed on the
OLED display of the transmitter, and the string
will disappear after the reset.
Short press
the button“-”
Operation Description
“H” (High-gain mode):It is suitable for long distance,
and its anti-interference ability is weaker than "L" mode.
The string will disappear on OLED screen after
switching to “H mode”.
Blinking in Red
Successful Bootup
During booting process
Low Battery Warning
Calling

07 08
V-Mount
RX: 3060
Antenna Interface
Tally(DB9)
RJ-45
RS232/422
SDI Out
DC-IN
HDMI Out
Antenna Interface
OLED Display
LNA ON/OFF
CH/WPS
Reset
Power Button
Receiver Key Operation
Function Operation Description
Frequency
channel
switching
Short press
the “CH/WPS”
button about 1S
Channel number increases one cycle from
CH1 to CH11 when each short pressing. After
receiver frequency switching, transmitters
will automatically display the updated channel
number.
Code matching
Press the “CH/
WPS” button for
about 3s
During the code matching process of the
transmitter and receiver, the word “WPS”
will always be blink displayed on the OLED
display, and the string will disappear after
the code matched. The transmitter and
receiver need to be in code matching
status at the same time to achieve
code matching success.
OLED display
switching
between
landscape
mode and
portrait mode
Short press the
“LNA ON/OFF”
button for
about 1s
Short press the “LNA ON/OFF” button,
and the display will switch between
landscape mode and portrait mode.
Reset decode
board
First, short press the
[RESET] button for
cyclical selection
among 1, 2, 3 and 4 to
reset the
correspoding decode
board. Then press
and hold the [RESET]
button for 3s to
confirm the restart.
After long pressing the button to confirm,
the “RESET” string will be displayed on
the OLED display for 3s, and the string
will disappear after the decoding board
begins to reset.
V-mount Plate
High-gain and
low-gain mode
switching
Hold the “LNA
on/off” button for
3 seconds to
switch the mode.
OLED without “L”
letter means
high-gain mode.
OLED with “L”
letter means
low-gain mode.
Line-of-sight scenarios:
TX-to-RX <200m/656ft: L(low-gain)
mode is recommended.
RX-to-LX >=200m/656ft: H(high-gain)
mode is recommended.
None-line-of-sight scenarios
(Human or wall blocking signal):
H(high-gain) mode is recommended.

OLED Display
RX: 3081
09 10
Broadcast call
+
-
SP K
/
BeamLink-U ltimate
In ter co m RX
RJ45
ALL 1 2 3 4 MUTE
MIC MIC/SPK VOL+VOL- Speaker
One-to one
full-duplex call
-
Short press the
MUTE” button“
Mute
Whether in one-to-one or broadcast mode,
the microphone at the live production terminal
is turned off. At this time, the live production
can hear the voice from the transmitting terminal,
but the transmitting terminal cannot hear the
voice from receiver.
Increase the volume, the system will remember
the current settings, and no resetting is
required next time.
Director mute1-4 Intercom switchBroadcast
Power Switch DC-IN
Tally In
Intercom Receiver
Function Operation Description
Short press the
ALL” button“
Enter the broadcast call mode, the receiver
speak, and all the transmitters listen.
Short press one of
the 1~4” buttons“
Receiver makes a single full duplex call to the
one of the selected transmitter.
Increase the
volume
Short press
the button“+”
Decrease the
volume
Short press
the “-”button
Decrease the volume, the system will remember
the current settings, and no resetting is required
next time.
Hands-free mode Pull out
the headphones
Hands-free microphone and speaker
will be activated.
Headphone mode Insert the
headphones
Hands-free microphone and speaker will be
turned off, and the headphones will be activated.

10 11
H D M I
S D I H D M I
BeamLink-Ulti mate
tX
BeamLink-Ulti mate
tX
BeamLink-Ulti mate
tX
BeamLink-Ulti mate
tX
BeamLink-U ltima te
tX
BeamLink-U ltima te
tX
HDMI Input
Product Installation
2. Please fix the transmitter via the screw at the bottom or the V-mount at the back,
and place it at a height of around 1.5 to 2 meters above floor. Please make sure
that the distance between each transmitter is more than 1 meter.
1. Please install all the antennas on the transmitter and make them in a fan shape
as shown in the picture.
Transmitter at a height of
around 1.5 to 2 meters
above floor.
3. Please connect the transmitter and camera with SDI or HDMI cable.
For transmitter
Distance>1m Distance>1m Distance>1m
SDI Input

00:00:00
12 13
headphone
Receiver Installation
1. Please install all the antennas on the receiver, and make them in a fan shape
as shown in the picture.
2. Please place the receiver at a height of around 1.5 to 2 meters above floor.
Receiver can be placed in vertical or horizontal positions, and can be fixed via
the screw at the bottom or V-mount at the back. Please install the affiliated
metal stand before placing the receiver in vertical position.
3. Please connect the receiver and video switch console or monitor
with SDI or/and HDMI cable.
install the
affiliated
metal stand
A: Horizontal placement
B: Vertical placement
Place the receiver at a
height of around 1.5 to
2 meters above floor.
H D M IH D M IH D M IH D M I
HDMI Out
S D I S D I
H D M IH D M IH D M IH D M I S D I
S D I S D I
HDMI Out
HDMI Out
HDMI Out
SDI Out
SDI Out
SDI Out
SDI Out
Receiver:3081
Receiver:3060

HDMI/SDI
HDMI/SDI
RTSP
14 15
4. The receiver can be powered by both the V-mount lithium battery and DC-IN port via
the affiliated power adapter. If the mentioned two types of power supply are
connected at the same time, the lithium battery is prioritized in power supplying,
and the battery will switch to the power adapter for power supplying automatically
after the battery power is exhausted.
This system supports tally function. When tally input is connected to GND, tally out
will be 5V voltage, which can provide 200mA max source current. And when tally
input is OPEN(disconnected to GND), tally out will be low.
Power
Li-battery
Product Application
Standard mode
In standard mode, the four channel video sources are connected to the four
transmitters via HDMI or SDI cable respectively. The receiver will receive the four
channel signals and transport them to switch console or/and monitor via
HDMI SDI.or/and
Headphone
Camera-1 TX-1
Headphone
Camera-2 TX-2
Headphone
Camera-3 TX-3
Headphone
Camera-4 TX-4
500m/1640ft
Four channel
Full-HD in One
RF Channel
RX-1
RX-2
*Tally
*RS232/422
Monitor
Switch Console
Live Streaming network
Headphone

16 17
RESET
CH 2
L1
VIDEO
TX:7081
L
X
VIDEO
WPS
Reset
RTSP The device is Streaming mode
RJ45
RJ45
Microphone icon
External audio input mode
Display the intercom volume of the transmitter
Standard mode
CH*
Streaming mode
In streaming mode, the four channel video sources are connec to
the four transmitters via HDMI or SDI cable respectively. The receiver will
receive the four RTSP from the four transmitters and send
them to the switch console through the LAN port.
and watch the live video on the mobile phone, tablet .
ted
streamings
You can also connect
the receiver with mobile devices such as your mobile phone, tablet and
PC via WiFi, and PC
Camera-1 TX-1
Headphone
Headphone
Camera-2 TX-2
Camera-3 TX-3
Headphone
Camera-4 TX-4
Headphone
500m/1640ft
Four channel
Full-HD in One
RF Channel
RX-1
RX-2 Headphone
Switch Console
PC
Monitoring on
Mobile Devices
OLED Display Description
Gain mode
Transmitter ID Signal icon
Video
Reset & Reboot
Frequency Channel
Volume icon
Icon Content Status
Transmitter ID Numbers 1~4 Four transmitters are numbered 1, 2, 3 and 4, respectively
Gain Mode Low-gain mode
Blank High-gain mode
Signal Icon Signal bar
Volume icon Volume bar
Connecting not complete
Successful network connection
Video
Blank No video signal input
Video signal input connected
In code matching status
Reset & Reboot
The device is resetting and rebooting
Blank
Frequency Channel Display current frequency channel (1~11)
Live Video Cloud Center

VIDEO
4
VIDEO
3
VIDEO
2
VIDEO
1
CH2
RX:3060
18 19
Transmitter ID Four transmitters are numbered 1, 2, 3
and 4, respectively
Video No video signal received from TX
VIDEO Video signal received from TX
CH*
Icon Content Status
Frequency Channel
Numbers 1~4
Blank
Display current frequency channel (1~11)
Signal Icon X
Signal bar Successful network connection
Connecting not complete
Frequency Channel
Transmitter ID Signal Icon
Video
Intercom Receiver:3081
1 2
1 2
Display the status of the corresponding
transmitters respectively.
Signal status “X” or signal bar
The signal bar is displayed when the wireless
signal at the corresponding transmitting
terminal is connected, otherwise “X”
is displayed.
Display volume Display the current relative volume
Telephone symbol
When the phone is displayed, it indicates
that the channel voice call is connected.
Volume
Call status
Corresponding transmitter is in the idle status.
Transmitter ID
Signal Icon
Volume icon
Icon Content Status
Transmitter ID Numbers 1~4
Call status
Blank

20 21
DB9_FEMALE
J15
GP8
GP7
GP6
GP5
GP4
GP3
GP2
GP1
5
9
4
8
3
7
2
6
1
SH1
SH2
Both the 3060 and the 3081 tally ports are available, but only one of them
can be used at same time.
Note:
DB9 pin Tally定义 说明
11R Channel 1 red
6
2
7
3
8
4
9
5
1G
2R
2G
3R
3G
4R
4G
GND
1
2
3
4
5
6
J16
PHONEJACK STEREO SW
RCLamp0521PA
D13
D12
RCLamp0521PA
Tally_Red
Tally_Green
Functional Instructions
Tally function
Insert the Tally light into the transmitter’s Tally output interface first,
then connect the to the receiver ’s Tally input interface,
and then control the Tally light of the four transmitters through the switch
console. When tally input is connected to GND,tally out will be 5V voltage,
which can provide 200mA max source current.And when tally input is OPEN
(disconnected to GND),tally out will be low.
switch console
Tally interface of the transmitter and receiver: The transmitter’s Tally
interface is a standard φ3.5 headphone interface. The receiver ’s Tally
interface is a DB9 female.
Tally light output interface:
The DB9 header of the Tally input interface is
defined as follows:
Channel 1 green
Channel 2 red
Channel 2 green
Channel 3 red
Channel 3 green
Channel 4 red
Channel 4 green
Ground Connection

22 23
RS232/RS422 transparent transmission
Name Description
NC NC
P12V
1
2
NC NC
TXD
3
4
GND
RXD
5
6
1 3
2
456
RXD-
P12V
TXD-
TXD+
GND
RXD+
RS232 RS422
This interface defaults to RS232 function. For RS422 function, contact the
sales staff in advance for customized information!
Pin No Name Description
No voltage output by default
(Reserve 12V voltage output)
Transmit data TX
Ground
Receive data RX
Receive data RX-
No voltage output by default
(Reserve 12V voltage output)
Transmit data TX-
Transmit data TX+
Ground
Receive data RX+
Log in to the backplane parameter settings page to change the baud rate settings:
(For specific operating steps, refer to “Video Parameter Settings”)
Attached: Baud rate settings
Description:
Streaming Function
When the receiver is set to streaming mode, the transmitter needs to
switch to streaming mode. At this time, the word “RTSP” is displayed
on the transmitter’s OLED display, the SDI and HDMI ports at the receiver
have no video output, and the video is transmitted to the streaming media
software through the LAN port of the receiver for decoding .
In this mode,video is decoded using software .And there are lots of IP based
decoding software on market. The following is an example of common VLC
streaming media software:After the transmitter and receiver build a
network connection, the transmitter network indicator is always on,
the receiver network connection display normal; the transmitter is connected to
the HDMI or SDI video source, and the receiver’s network port is connected
to the streaming device.
Take the VLC on PC as an example. After running VLC, select to turn on
the network stream.Fill in the address “rtsp://xx.xx.xx.xx/media/live/0
where xx.xx.xx.xx is the corresponding transmitter IP address. Click “Play”
to start.
”,
Note that the transmitter must be connected to the video source, and the
IP address of the device runing VLC (such as a computer) must be
the same network segment as the IP address of the encoding board.
Otherwise, the streaming will fail.

24 25
Encoder/Decoder Configuration and Upgrading
Receiver module: (Since the receiver has four decoders, there are four
corresponding IP addresses need to be configured)
Version:CM3060V3.15
IP ETHADDR
192.168.1.212
GROUP
2222
LATENCY_MODE
1
Serial Baud Rate 2400 9600 19200 38400 57600 115200
File Upload: 选择文件 未选择任何文件 (Select A Local File)
Save the configuration and then reboot...
Save Environment
1
2
Software version
Decoder IP address (192.168.1.211~214)
Corresponding transmitter ID (1111/2222/3333/4444)
Serial baud rate
Software upgrade:
① Select the file to be upgraded
② Click Save to complete the upgrade
Standard Mode Bitrate
8000 Range(1000-25000)
RTSP Bitrate
Range(1000-15000)
SDI Audio Mode 01
Serial Baud Rate 2400 9600 19200 38400 57600 115200
File Upload: 选择文件 未选择任何文件 (Select A Local File)
Save the configuration and then reboot...
Save Environment
1
2
Transmission bitrate
RTSP streaming bitrate
Serial baud rate
Software upgrade: ① Select a file; ② Click Save
IP ETHADDR
192.168.1.112
GROUP
2222
Transmitter Encoder Case (transmitter 2):
Transmitter IP address(192.168.1.111~114). Do not change the IP,
otherwise the wireless connection will be shut down.
Transmitter ID (four devices correspond to 1111, 2222,
3333 and 4444, respectively), Do not change the ID, otherwise the wireless
connection will be shut down
Keep the computer connected to the receiver through LAN port,
and keep the receiver connected with all transmitters normally.
Open internet browser, and enter transmitter’s encoder or receiver’s
decoder IP address in the address bar to enter the parameter settings page.
All transmitter ’s encoder and receiver’s need to be configured
one by one, please refer to the following configuration case.
decoders
Receiver Decoder Case (Decoder 2):
192.168.1.201, 192.168.1.202, 192.168.1.203, 192.168.1.204
Encoder IP 192.168.1.111, 192.168.1.112, 192.168.1.113, 192.168.1.114
192.168.1.100
Receiver
192.168.1.211，192.168.1.212，192.168.1.213，192.168.1.214
Transmitter
Wireless
transmission
module IP
(WiFi IP)
Decoder IP
Wireless
transmission
module IP
(WiFi IP)
Each transmitter has one encoder, and its configuration and software
upgrading need to be implemented on its encoder . Since the receiver has
four decoders, the configuration and software upgrading need to be
implemented on its each decoder respectively.
Each transmitter has one wireless transmission module and one encoder.
Receiver has one wireless transmission module and four decoders.
All modules and each encoder/decoder have their respective IP address as
follows, and all configuration and upgrading operation must be
implemented under its own IP address.

26 27
Mode:STA
WiFi IP:192.168.1.201
Encoder IP:192.168.1.111
Wireless Transmission Module Upgrading
1. The transmitter operates the same as the wireless software upgrade
of the receiver.
2. The back of each device’s body will be labeled with the IP address of
WiFi and the IP address of the encoder/decoder. The default IP
addresses are as follows:
(Take the following figure as an example: The device’s operating mode,
WiFi IP(wireless transmission module IP), and IP of the Encoder/Decoder
can be found.)
First, connect the computer to the LAN port of the receiver;
Then enter the device’s WiFi IP (wireless transmission module IP) in the
address bar to enter the login page:
After successful login, enter the WiFi board parameter page of the device:
Enter username: admin
Enter password: admin
192.168.1.201, 192.168.1.202, 192.168.1.203, 192.168.1.204
Encoder IP 192.168.1.111, 192.168.1.112, 192.168.1.113, 192.168.1.114
192.168.1.100
Receiver
192.168.1.211，192.168.1.212，192.168.1.213，192.168.1.214
Transmitter
Wireless
transmission
module IP
(WiFi IP)
Decoder IP
Wireless
transmission
module IP
(WiFi IP)
Each transmitter has one wireless transmission module, and the software
upgrading needs to be implemented on each transmitter. Receiver also has
one wireless transmission module, and the software upgrading needs to be
implemented on it accordingly.
Information label on transmitter:

28 29
Select the “Upgrade” option in the “System” column.
On the “Upgrade” settings page:
The software for the product WiFi board can be upgraded:
1. Select the software file to be upgraded
2. Click to upgrade
ITEM
4*4 MIMO 5dBi External antenna
OFDM
19dBm
EVM ≤-28dB
Receiving Sensitivity ≤-70dBm
Wireless 802.11n
Network encryption WPA2/WPS
Network model Point to point, RTSP
Transmission Delay 70ms(min)
code function Support automatically code matching
HDMI Protocol Support HDMI 1.4
TX:7060 RX:3060/3081
Frequency
Antenna
Modulation mode
Transmission Power
Transmission Distance 500m(video code rate: 8Mbps per channel)
Product Specifications
Bandwidth 40MHz
5190 Hz(1), 5230 Hz(2), 5270 Hz(3), 5310 Hz(4),
5510 Hz(5), 5550 Hz(6), 5590 Hz(7), 5630 Hz(8),
5670 Hz(9), 5755 Hz(10), 5795 Hz(11)
Video Format
SDI/HDMI Embedded audio
Audio Format
SMPTE 296M 720p50, 720p59.94, 720p60,
SMPTE 274M 1080i50, 1080i59.94, 1080i60, 1080p23.98,
1080p24, 1080p25, 1080p29.97, 1080p30
SMPTE424M 1080p50, 1080p59.94, 1080p60
SDI：
720p50, 720p59.94, 720p60, 1080i50, 1080i59.94,
1080i60, 1080p23.98, 1080p24, 1080p25, 1080p29.97,
1080p30, 1080p50, 1080p59.94, 1080p60
HDMI:
Audio via video wireless transmission: PCM
Sampling rate: 48KHz Number of bits: 16bit
Intercom audio: 3.5mm interface analog input and output

30 31
Video Compression
Format H.264
Remote control RS232/RS422
IO port signal return Support Tally signal return
Interface
SDI in * 1; HDMI in * 1;
Tally output * 1;
Lemo power coordinates *1;
Antenna sub *4; Key * 3;
Ship type power switch *1;
OLED display screen *1;
Np-F970 battery holder *1
SDI output *4; HDMI output *4;
DB9(Tally in) * 1; Antenna sub *4;
Power supply coordinate *1;
Metal power switch *1;
Display screen *1; Key * 3;
Battery button connection seat *1
Temperature -10°C - 50°C(Working)；- 40°C - 80°C(Storage)
Operating Power Supply DC 12V/2A DC 12V/3A
Operating voltage 7-17V
Power Consumption 10W 20W
Trouble Shooting
SolutionsTrouble
If mosaic, jams, smear
or frame loss appear
during use
Lift the transmitter and receiver as high as possible,
to 1.5-2m or more;
The antennas are installed in fan-shape and facing for
ward to receiver, and the transmission effect is the best;
The LNA mode is set in H (high-gain mode);
When multiple transmitters work at the same time,
ensure that the transmitters are at least 1m apart from
each other;
If there is still a mosaic or a jam, switch the product
frequency to the other frequency channel.
If in/ out video
resolution not
matching or display
compatibility related
Confirm the software version of the
and contact the technician in time. If the software version
is confirmed to be too old, it is necessary to upgrade
the software.
encoder and decoder
If there is no
connection
during use,
It is divided
into 2 cases:
In close range ( , if the transmitter
and receiver are connected to 4 antennas, the distance
needs to be extended to 5m, and the LNA mode should
be set to L (low-gain mode); when multiple transmitters
work at the same time, ensure that the transmitters
are at least 1m apart from each other;
situation TX-to-RX<2m)
In the long-distance situation, lift the transmitter and
receiver as high as possible, to 1.5-2m or more; the
antenna is fan-shaped and facing for ward,the LNA mode
is set to H (high-gain mode); when multiple transmitters
works at the same time, ensure that the transmitters
are at least 1m apart from each other.
When the receiving
terminal cannot hear
the other party’s
voice when speaking
one-on-one
a: Confirm whether it is in one-to-one mode;
b: Press the “ALL” button again, and then press the
button at the corresponding transmitting terminal;
c: Whether the headphones are loose; and
d: Whether the headphones malfunction, try again after
replacing the headphones.

31
Precautions
a. Do not plug in or pull out the HDMI cable of the transmitter and receiver
during normal use.
c. When the OSD prompts that code matching fails after trying code matching,
reboot the transmitter and receiver to see whether they can be connected
normally. Perform code matching again when it is still unable to be
connected after restarting.
d. When there is no video appear on display after change video resolution
parameters on transmitter, pull out and then plug in the HDMI cable of the
transmitter or receiver.If there is still no video appear, power off and restart
the transmitter and receiver.
e. When the network cannot be connected for a long time after switching
frequency channel, reboot the transmitter and receiver.
f. When the transmitter and receiver devices are connected normally,
there is no output on the monitor at the receiver, or the video output is
abnormal, re-plug the HDMI cable of the receiver and check whether the
monitor is changed to standby mode. If it is still unable to output normally
after the above operation, try to replace the display device.
2. If there is a picture jam or mosaic during use, it is generally caused by
interference in the network. Therefore, try switching the network frequency
channel to avoid the interference band. For the frequency switching
operation,please refers to the frequency switching operation
instructions.
channel
channel
b. Connect the transmitter to the video source and connect receiver to
a monitor via HDMI and then power on the transmitter and receiver.
1. If transmitter or/and receiver use HDMI cable:(a~f)