Cybertec DMM Series User manual

DMM Series
3G / GSM Modem Router
Quick Start Guide
Document Number: 0013-001-000508
Version: 1.0 (08 March, 2016)

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
Documentation Control
Generation Date: March 10, 2016
Copyright c 2016 Cybertec Pty Limited
All rights Reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Cybertec Pty
Limited.
Cybertec Pty Limited has intellectual property rights covering subject matter in this document. Except as expressly
provided in any written license agreement from Cybertec Pty Limited, the furnishing of this document does not give you
any license to this intellectual property.
Legal Information
The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either
express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular
purpose, are made in relation to the accuracy and reliability or contents of this document. Cybertec Pty Ltd reserves the
right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Cybertec Pty Ltd be responsible for any loss of data or income or any special, incidental,
and consequential or indirect damages howsoever caused.
More information about Cybertec can be found at the following Internet address: http://www.cybertec.com.au
Page 1

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
Contents
1 Introduction 3
2 Safety 3
3 Care Recommendations 3
4 Indicators and Interfaces 4
4.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.3 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.4 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Installation 6
5.1 Installing the SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.2 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.3 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.4 Functional Earth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.5 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6 Accessing the Web Interface 9
6.1 Windows PC Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.2 Connecting to the DMM Series Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7 Basic Configuration 12
7.1 Configure the Wireless interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.2 Configure the LAN interface and DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.3 Configure clients to use the DMM Series Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8 Troubleshooting 18
8.1 DMM Series Modem does not start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.2 Cannot connect to web pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.3 Network Status Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.4 Connection Status Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Page 2

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
1 Introduction
The Cybertec DMM Series product range includes several models of 3G and GSM Modems.
This guide will provide an overview of the features and interfaces of the DMM Series Modem . Installation of the unit and
antenna will be described as well as the configuration of the unit for a standard Internet connection. Further information
can be obtained from the MRX Configuration and Management User Manual.
2 Safety
Please observe the general safety precautions outlined in this manual during all phases of
operation and service of the device. If you do not comply with these precautions or with specific
safety warnings contained elsewhere in this manual or on the product itself, you will violate the
standards of design, manufacture, and intended use of the product. Cybertec does not assume
any liability for failure to comply with these precautions.
Read this manual completely and make sure it is understood fully before commencing
installation. Check that the intended application does not exceed the safe operating
specifications for this unit. This unit should only be installed by qualified personnel. The power
supply wiring must be sufficiently fused, and if necessary it must be possible to manually
disconnect the unit from the power supply.
3 Care Recommendations
To maintain correct operation of unit and to fulfil the warranty obligations the following care recommendations should
be followed. This unit must not be operated with the covers removed. Do not attempt to disassemble the unit, no user
serviceable parts are contained within the unit. Do not drop, knock or shake the unit, rough handling may cause damage
to internal circuit boards. Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit. Do not
expose the unit to any kind of liquids (rain, beverages, etc), the unit is not waterproof. Keep the unit within the specified
humidity levels. Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical part may be
damaged.
Page 3

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
4 Indicators and Interfaces
This section describes the indicators and interfaces for the DMM Series.
4.1 Front Panel
The Ethernet ports, antenna connector, power connector and indicators are located on the front panel as show in figure 1.
Figure 1: DMM Series front panel.
Page 4

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
4.2 Rear Panel
The rear panel contains the SIM slot, functional earth and DIN Clip as shown in figure 2.
Figure 2: DMM Series rear panel.
4.3 Indicators
The DMM Series modem has single power / status LED on the front panel of the unit. The indicator will light green when
power is applied and will light red when an error or fault condition is detected.
4.4 Ethernet
The Ethernet ports are on the front of the unit, the port has a LED indicating the connection speed and a LED indicating
activity as shown in Figure 3. The Ethernet port is capable of auto-negotiation, meaning cross-over cables are not required.
Figure 3: Ethernet ports.
Page 5

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
5 Installation
The steps required to install the DMM Series Modem are described.
The DMM Series Modem should be mounted in a clean and dry location, protected from water,
excessive dust, corrosive fumes, extremes of temperature and direct sunlight. The unit uses convection
cooling, allow sufficient ventilation to ensure adequate cooling of the modem.
5.1 Installing the SIM Card
Before removing or inserting the SIM card, ensure that the power has been turned off and the power
connector has been removed from the unit.
Damage may result to the unit if excessive force is used to remove or insert the SIM.
The SIM card slot is located on the rear of the unit.
Figure 4: Inserting the SIM card.
•Insert the SIM card into the SIM card drawer with the contacts facing away from the closest edge, as shown on the
right of Figure 4.
•Push the SIM until in clicks, indicating it is in place.
•If inserted correctly it should be just behind the panel.
•To remove the SIM press until it clicks then release and it will spring out.
Page 6

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
5.2 Antenna
The antenna connector on the DMM Series Modem is an SMA type and found on the rear of the unit. The supplied
antenna is intended for direct mounting to the SMA connector. Attach the antenna as shown in Figure 5. Ensure that the
connecting nut is done up tightly in order to ensure a good connection.
Figure 5: Antenna connected to SMA connector.
5.3 Power Supply
The DMM Series Modem requires a DC power source in the voltage range of +10VDC to +30VDC. The power connector
accepts a screw terminal plug which should be wired as shown in figure 6 and plugged into the power connector on the
rear of the unit.
Figure 6: Power plug wiring and Power connector.
The unit is designed to self protect from permanent damage if the voltage exceeds +36VDC or if
reverse polarity is applied. In the case of either event the modem may need to be returned for service.
Page 7

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
5.4 Functional Earth
In order to comply with emission and immunity requirements the unit should be grounded. Ensure that the functional
earth lug is connected to earth ground during normal use. The Functional earth termination screw is on the rear of the
unit.
Figure 7: Functional earth termination screw.
5.5 Mounting
The DMM Series Modem is designed to be DIN rail mounted. Using the DIN rail clip on the rear of the unit ensure the
unit is securely mounted to a suitable DIN rail.
Page 8

Cybertec Pty Limited
Copyright c 2016
Document: 0013-001-000508
DMM Series Quick Start Guide
Version: 1.0
08 March, 2016
6 Accessing the Web Interface
All configuration of the DMM Series Modem is performed via the web interface. In order to view the web pages a
computer with a fixed IP address, on the same sub-net as the DMM Series Modem, will need to be connected to one of
the LAN ports.
•The default IP settings of the DMM Series Modem are:
◦IP Address: 10.10.10.10
◦Netmask: 255.255.255.0
•The recommended IP settings for the PC used to configure the DMM Series Modem are:
◦IP Address: 10.10.10.20
◦Netmask: 255.255.255.0
◦Default Gateway: 10.10.10.10
◦Primary DNS: 10.10.10.10
Although it is possible to connect the DMM Series Modem directly to a Local Area Network (LAN) it
is recommend that the network configuration as described in this section be performed prior to doing
so.
6.1 Windows PC Network Settings
The following describes how to configure the network settings of a Windows XP PC with the IP settings listed above, so
that it can access the DMM Series Modem.
This procedure will change the network settings of the Windows PC, if the PC is connected to a
network the connection should be removed before performing the changes. To restore the network
settings of the PC record the current settings at Step 6 in the following procedure, then when the DMM
Series Modem has been configured following the procedure again and use the recorded values at Step
6.
1. Open the Control Panel by selecting Start ⊲Control Panel.
2. Double click the Network Connections icon.
3. Double click the Network icon.
4. The Local Area Connection Status dialogue box will be displayed, as shown on the left of Figure 8, click the Prop-
erties button.
Page 9