CyClone BX212 Owner's manual

Self-Cleaning Range Hoods
Insert Range Hoods
Please read all instructions before installing and operating.
All wiring and installation must be in accordance with CEC, NEC and local electrical codes.
READ AND SAVE THESE INSTRUCTIONS
Models:
BX212, BX215, BX155, BX600, BX360 CLX60, SS130,
BXB606, BXB609, BXB612
Installation and Operation Instructions

2 Cyclone Insert Installation - English 3Cyclone Insert Installation - English
IMPORTANT SAFETY INSTRUCTIONS
•
•
failure to observe the instructions given here for installation,
maintenance and suitable use of the product.
•
due to negligence, and the warranty of the unit automatically
expires due to improper installation and maintenance.
WARNING
• Suitable for use in household cooking area.
• For residential cooking use only. Do not use to exhaust
hazardous or explosive materials or vapors.
• Two installers are recommended because of the size and
weight of this hood.
• Do not use more than 20 watts per halogen lightbulb for
this model.
• Light bulbs combined are not to exceed 40 watts.
• Use LED bulb, 1.5W Maximum per bulb, for SS130.
• *Bulb & socket may change.
•
dishwasher friendly, depending on the amount of grease
and the type of dish-washing solutions used it may cause
CAUTION
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
1. Never leave the range unattended at high settings.
2. Always turn hood ON when cooking at high heat or when
3. Use proper pan size. Always use cookware appropriate for
the size of the surface element.
4.
ventilating fans frequently. Do not allow grease to
5. Use HIGH setting on hood only when necessary.
6. Don’t leave hood unattended when cooking.
7.
8.
9. Not for outdoor use.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. .rerutcafunamehtybdednetnirennamehtniylnotinusihtesU
2.
at service panel and lock service panel to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device to the service panel.
3. Installation work and electrical wiring must be done by
4.
manufacturer’s guideline and safety standards as published
by the local code authorities.
5. When cutting or drilling into walls or ceilings, be careful
not to damage existing electrical wiring and other hidden
utilities.
6.
.sroodtuodetnevebsyawlatsumsnafdetcud,riatsuahxe
Do not vent exhaust air into spaces within walls, ceilings,
attics, crawl spaces, or garages. Do not connect this fan
with any solid-state speed control device.
7.
venting.
8.
and at a suggested maximum of 36” above cooktop for
best capture of cooking impurities. For a gas range, the
bottom of the hood MUST NOT BE LESS than 30” above
cooktop.
WARNING
• Do not repair or replace any part of this appliance unless
•
and restarts, contact the Cyclone service department.
Ensure that the hood is mounted at the recommended
mounting height.
•
cuts and abrasions during installation and cleaning.
WARNING

4 Cyclone Insert Installation - English 5Cyclone Insert Installation - English
CONTENTS
Important Safety Instructions 3
Damage Inspection 5
Ducting 5
Mounting Heights and Clearance 6
Wiring Installation 6
Tools and Materials Required 7
SS130 Installation - Parts supplied 8
SS130 Insert Hood Installation 9
SS130 Installation - Installation Cutout Templates 10
BX155/BX212/BX215 Installation - Parts supplied 11
BX212/BX215 Insert Hood Installation 12
BX155 Insert Hood Installation 13
BX155/BX212/BX215 Installation - Installation Cutout Templates 14
BX600/BX360/CLX60 Installation - Parts supplied 15
BX600/BX360/CLX60 Insert Hood Installation 16
BX600/BX360/CLX60 Installation - Installation Cutout Templates 17
BXB606/BXB609/BXB612 Installation - Parts supplied 18
BXB606/BXB609/BXB612 Insert Hood Installation 19
BXB606/BXB609/BXB612 Installation - Installation Cutout Templates 20
21
Troubleshooting 22
Maintenance 23
Control Panel 24
Cyclone Range Hoods Limited Warranty 25
DAMAGE INSPECTION
• Please fully inspect unit for damage before installation.
• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the customer), repair of replacement must be made by arrangement between
customer and installer.
• Once installed, all damages will be assumed the responsibility of the installer.
DUCTING
•
•
to duct air outside – do not vent exhaust air into spaces
within walls, ceilings, attics, crawl spaces, or garages.
WARNING
• It is best to use rigid type metal ducts. Flexible ducts can
• Reduce the number of transitions and turns as much as
possible. If a reducer is used, install a long reducer instead
of a pancake reducer. If turns and transitions are required,
install them as far away from the opening as possible and
as far apart between two as possible.
CAUTION
• 450 - 699 CFM requires a minimum of 6” diameter duct.
700 - 949 CFM requires a minimum of 8” diameter duct.
950 - 1200 CFM requires a minimum of 10” diameter
duct. Any use of duct contrary to above, can result in the
warranty being rendered null and void.
•
to the outside wall or the roof. If it is turned downward
anywhere intheventingsystem, the warranty is automatically
voided.
WARNING
Fasten all connections with sheet metal screws and tape all joints
Do not cut a joist or stud unless absolutely necessary. If a joist or
stud must be cut then a supporting frame must be constructed.
Before making cutouts make sure there is proper clearance within
the ceiling or wall for the exhaust vent.
inserts:
Roof Pitch with Cap
and Flashing
Side Wall Cap with
Gravity Damper
Side Wall Cap
with Gravity
Damper
Soffit or Crawl Space
Additional parts not provided.

6 Cyclone Insert Installation - English 7Cyclone Insert Installation - English
MOUNTING HEIGHTS AND CLEARANCE
•
cooking surface. If pairing your range hood with a gas
stove minimum mounting height must be 30” above the
cooking surface.
WARNING
Minimum mount height between range top to hood bottom should
be no less than 28” for electric or ceramic stoves, and no less than 30”
mounted too low could result in heat damage. Hoods mounted too
Check your ceiling height and the hood height maximum before
you select your hood.
Hood installation height above cook top is the user’s preference.
be in drawing out cooking odors, grease and smoke.
WIRING INSTALLATION
Min:
Ceramic/Electric
28”
Gas 30”
Max:
36”
36”
Install the Electrical Power Supply
Install a junction box inside the upper corner of the cabinet. For
the model SS13024, it should be installed at a minimum of 8” away
from the center of the cabinet and 12” above the bottom of the
cabinet. For the models SS13030, BX21228/BX21528, BX600/
CLX60, it should be installed at a minimum of 11” away from the
center of the cabinet, and 12” above the bottom of the cabinet. For
the model BX21234/BX21534, it should be installed at a minimum
of 13” away from the center of the cabinet, and 12” above the
bottom of the cabinet.
by a circuit breaker or time delay fuse.
Preparation for Vent and Exhaust Duct Connection
1. To connect a rectangular vent to a round exhaust duct (or vice
versa), use a connecting duct and adapter.
2. If the duct size is greater than what is equipped on the product,
duct size is less than what is recommended for your product,
and the warranty can be rendered null and void.
3. An exhaust duct needs to be cut if there is not an existing duct
in your home. Please consult/hire a professional to complete
the work properly. For top venting, a rectangular or a 6”
round hole needs to be cut through the ceiling or the back
When there is no access to the top of the hood, carefully pull down
the metal duct through the custom hood base hole. Slide this duct
over the adapter/damper. Make sure the adapter/damper assembly
enters the ducting. Seal the connection with aluminum tape.
Ducting Connection
TOOLS AND MATERIALS REQUIRED
• Electrical drill or ratchet driver
• Phillips screwdriver #2 or driver bit
• Straight blade screwdriver
• Wire stripper or cutter
• Tape measure
• Electrical supplies for wiring (i.e. wire connectors,
electrical tape)
• Aluminum foil tape and/or duct tape
• Hammer
• Jigsaw or saber saw
• Step ladder
• Pencil
Ceramic/Electric 28”
Max: 36”
Gas 30”
Min:

8 Cyclone Insert Installation - English 9Cyclone Insert Installation - English
SS130 INSTALLATION - PARTS SUPPLIED
1 × Hood 1 × Round Adapter
HARDWARE PACKAGE
1 × Rectangular Oil Collector
6 × Adapter Screws
1 × Plastic Adapter Seal
PRE-INSTALLED
2 × LED Lights
(1.5W per bulb)
*Bulb & socket may change.
Preparation for Installation
1. Unpack range hood and check contents. Note: Be cautious of
sharp edges within the unit.
2. Cut the insert cutout at the bottom of the cabinet using the
given cutout measurements on page 10 (Figure 1).
3. Locate the cutout at the center of the bottom of the cabinet.
surface of the cabinet doors.
SS130 INSERT HOOD INSTALLATION
connection to an individual properly grounded branch circuit
protected by a circuit breaker or time delay fuse.
•
this unit.
•
in accordance with all applicable codes and standards.
WARNING
• At least two installers are required due to the weight and
size of the hood.
CAUTION
1.
2. Attach damper to rectangular cutout on top of the range
hood using the screws provided.
3.
hood mounts to the cabinetry by two spring loaded brackets,
one on each side of the range hood (Figure 2).
4. Once the range hood is through the cabinetry the brackets
place (Figure 3).
5. Pull the slide outwards to expose the inside of the range
hood. Locate the adjustable screw hole underneath both
sides of the hood.
6. Once located, use a Phillips screwdriver to tighten the
adjustable screw until the unit is tightly fastened to the base
of the cabinetry (Figure 4).
7. Make sure that the adapter is connected to ductwork.
8.
9. Connect the power plug to the junction box.
Install the SS130 Range Hood
Figure 3.
Figure 2.
Fasten Screws
Figure 4.
4 × Mounting Screws

10 Cyclone Insert Installation - English 11Cyclone Insert Installation - English
SS130 INSTALLATION - INSTALLATION CUTOUT TEMPLATES
19 ”
17 ”
¾”
Classic Collection Insert - Model: SS13024
Cut Out
10 ¼”
2” 2”
SS13024
BX155/BX212/BX215 INSTALLATION - PARTS SUPPLIED
1 × Hood BX212/BX212 1 × Round Adapter
(BX212/BX215 only)
HARDWARE PACKAGE
4 × Mounting Screws
1 × Rectangular Oil Collector
6 × Adapter Screws
(BX212/BX215 only)
INCLUDED IN UNIT
2 × Halogen Lights
(120V, 20W per bulb)
1 × Plastic Adapter Seal
(BX212/BX215 only)
1 × Hood BX155
25 ⅝”
24 ⅛”
¾”
Classic Collection Insert - Model: SS13030
Cut Out
10 ⅜”4 ”
2”2”
SS13030
31 ¼”
29 ¾”
¾”
Classic Collection Insert - Model: SS13036
Cut Out
10 ¼” 4 ”
2”2”
SS13036

12 Cyclone Insert Installation - English 13Cyclone Insert Installation - English
1. Place range hood on its side where the control panel and light
bulbs are on the bottom, closest to the table.
2.
the lights and 1 for the switch/controls. Gently squeeze the
plastic tabs and pull apart the connectors. (Figure 1)
3. Once all 3 wires have been disconnected, locate the four
side. Remove the 4 screws using your screwdriver or power
drill and place them aside as you will need them later on to
reattach the face. Remove the face and set it aside.
4. With the face removed, you will expose 4 holes in the body of
hood into the cavity of the cabinet and secure it by driving the
screws through the pilot holes and directly into the bottom of
the cabinet.
5. With the hood secured to the cabinet, you can now reinstall
the face and reconnect all the wires.
BX212/BX215 INSERT HOOD INSTALLATION
connection to an individual properly grounded branch circuit
protected by a circuit breaker or time delay fuse.
•
this unit.
•
.sdradnatsdnasedocelbacilppallahtiwecnadroccani
WARNING
• At least two installers are required due to the weight and
size of the hood.
CAUTION
Prepare for Installation
1. Unpack range hood and check contents. Note: Be cautious of
sharp edges within the unit.
2. Cut the insert cutout at the bottom of the cabinet using the
given cutout measurements on page 14.
3. Locate the cutout at the center of the bottom of the cabinet.
Installing the BX212/BX215 Range Hood
Top Panel
Figure 3.Figure 2.
Figure 4.
1.
2. Attach damper to rectangular cutout on top of the range
hood using the screws provided (Figure 2).
3.
the 4 screws using your screwdriver or power drill and place
them aside as you will need them later on to reattach the
face. Remove the face and set it aside (Figure 3).
4. Hold range hood upright, and insert range hood upward
into cabinet cutout. Secure the range hood to the cabinet
using the four screws provided. Two for each side (Figure 4).
5. Reattach and screw top panel onto range hood.
6. Make sure that the adapter is connected to ductwork.
7.
8. Connect the power plug to the junction box.
BX155 INSERT HOOD INSTALLATION
connection to an individual properly grounded branch circuit
protected by a circuit breaker or time delay fuse.
•
this unit.
•
in accordance with all applicable codes and standards.
WARNING
• At least two installers are required due to the weight and
size of the hood.
CAUTION
Prepare for Installation
1. Unpack range hood and check contents. Note: Be cautious of
sharp edges within the unit.
2. Cut the insert cutout at the bottom of the cabinet using the
given cutout measurements on page 14.
3. Locate the cutout at the center of the bottom of the cabinet.
Installing the BX155 Range Hood
Figure 1.
Once the cutout has been made to the insert:

14 Cyclone Insert Installation - English 15Cyclone Insert Installation - English
10 ⅝”
26 ½”
Classic Collection Insert - Model: BX21528
Cut Out
13 ½”
32”
Classic Collection Insert - Model: BX21534
Cut Out
SETALPMETTUOTUCNOITALLATSNI-NOITALLATSNI512XB/212XB/551XB
BX21228/BX21528
BX21234/BX21534
BX15522
20 ⅝”
10 ⅜”
Classic Collection Insert - Model: BX15522
Cut Out
BX600/CLX60 INSTALLATION - PARTS SUPPLIED
1 × Hood 1 × Round Adapter
HARDWARE PACKAGE
PRE-INSTALLED
2 × LED Lights
(1.5W per bulb)
4 × Mounting Screws
1 × Rectangular Oil Collector
1 × Plastic Adapter Seal
6 × Adapter Screws

16 Cyclone Insert Installation - English 17Cyclone Insert Installation - English
Install the BX600/BX360/CLX60 Range Hood
BX600/BX360/CLX60 INSERT HOOD INSTALLATION
connection to an individual properly grounded branch circuit
protected by a circuit breaker or time delay fuse.
•
this unit.
•
.sdradnatsdnasedocelbacilppallahtiwecnadroccani
WARNING
• At least two installers are required due to the weight and
size of the hood.
CAUTION
Figure 1.
Prepare for Installation
1. Unpack range hood and check contents. Note: Be cautious of
sharp edges within the unit.
2. Cut the insert cutout at the bottom of the cabinet using the
given cutout measurements on page 17.
3. Locate the cutout at the center of the bottom of the cabinet.
1.
2. Hold range hood upright, and insert range hood upward into
cabinet cutout. Mount the insert range hood to the cabinet
using four screws from inside the range hood (two screws on
each side). In addition, use four screws to secure the hood on
to cabinet surface.
3.
screws using your screwdriver or power drill and place them
aside as you will need them later on to reattach the face.
Remove the face and set it aside.. (Figure 2)..
4.
hood and unplug the two wires that lead to the lights and the
one wire that leads to the switch/controls.
5. Once the three wires are unplugged, you can completely
remove the face and set it aside. With the face removed, you
will be able to identify the four mounting holes that you will
use to secure the hood to the cabinet.
6. Hold range hood upright, and insert range hood upward
into cabinet cutout. Secure the range hood to the cabinet
using the four screws provided. Two for each side.
7. Reattach and screw the face onto range hood. Connect the
connectors of switch and two lights.
8. Make sure that the adapter is connected to ductwork.
9.
10. Connect the power plug to the junction box.
10 ¼”
26”
Classic Collection Insert - Model: BX60028
Cut Out
BX600/BX360/CLX60 INSTALLATION CUTOUT TEMPLATES
BX60028/BX36028/CLX6028
13 ⅛”
31 ⅜”
Classic Collection Insert - Model: BX60034
Cut Out
BX60034/BX36034/CLX6034
Figure 2.

18 Cyclone Insert Installation - English 19Cyclone Insert Installation - English
Install the Range Hood
BXB606/BXB609/BXB612 INSERT HOOD INSTALLATION
connection to an individual properly grounded branch circuit
protected by a circuit breaker or time delay fuse.
•
this unit.
•
.sdradnatsdnasedocelbacilppallahtiwecnadroccani
• BXB606 requires a minimum of 6” diameter duct,
BXB609 requires a minimum of 8” diameter duct,
BXB612 requires a minimum of 10” diameter duct. Any
use of duct contrary to above, can result in the warranty
being rendered null and void.
•
WARNING
• At least two installers are required due to the weight and
size of the hood.
CAUTION
Figure 1.
Prepare for Installation
1. Unpack range hood and check contents. Note: Be cautious of
sharp edges within the unit.
2. Cut the insert cutout at the bottom of the cabinet using the
given cutout measurements on page 17.
3. Locate the cutout at the center of the bottom of the cabinet.
1.
2. Hold range hood upright, and insert range hood upward into
cabinet cutout. Mount the insert range hood to the cabinet
using four screws from inside the range hood (two screws on
each side). In addition, use four screws to secure the hood on
to cabinet surface.
3.
screws using your screwdriver or power drill and place them
aside as you will need them later on to reattach the face.
Remove the face and set it aside.. (Figure 2)..
4.
hood and unplug the two wires that lead to the lights and the
one wire that leads to the switch/controls.
5. Once the three wires are unplugged, you can completely
remove the face and set it aside. With the face removed, you
will be able to identify the four mounting holes that you will
use to secure the hood to the cabinet.
6. Hold range hood upright, and insert range hood upward
into cabinet cutout. Secure the range hood to the cabinet
using the four screws provided. Two for each side.
7. Reattach and screw the face onto range hood. Connect the
connectors of switch and two lights.
8. Make sure that the adapter is connected to ductwork.
9.
10. Connect the power plug to the junction box.
Figure 2.
BXB606/BXB609/BXB612 INSTALLATION - PARTS SUPPLIED
1 × Hood 1 × Round Adapter
HARDWARE PACKAGE
4 × Mounting Screws
1 × Rectangular Oil Collector
(BXB606 only)
1 × Plastic Adapter Seal
(BXB606 only)
6 × Adapter Screws
(BXB606)
10 × Adapter Screws
(BXB609/BXB612)
PRE-INSTALLED
LED Puck Lights
(1.5W per bulb)
*Bulb & socket may change.