Cyfral PC-4000RV Assembly instructions

~1~
PC-4000RV DIGITAL PANEL
OPERATING, INSTALLATION AND PROGRAMMING MANUAL
1vO

~2~
1. introduction ................................................................................................................................................2
2. General......................................................................................................................................................3
3. Installation..................................................................................................................................................3
4. Connection.................................................................................................................................................4
5. Programming..............................................................................................................................................6
6. Camera module..........................................................................................................................................7
7. Miscellaneous ............................................................................................................................................8
1. INTRODUCTION
Before installing the device, read the following operating instructions. Installation may only be carried out by a
qualified person with the adequate qualifications.
This manual applies to the PC-4000 digital panel which is part of the CC4000 system. The description of
programming and setting up with the rest of the system elements can be found in the CC4000 System Manual.
Panel PC-4000 and devicesconnected to it are only allowed to be supplied with verylowvoltage (ELV) with a value
not exceeding the acceptable safe touchvoltage. Power devices (12V DC power supplies) must comply with EMC
standards and safety in accordance with applicable European Union standards and ensure full galvanic
isolation from the power grid.
The device is equipped with a 2.5 A fine fuse It is forbidden to connect foreign installations and devices to the
terminals of the PC-4000 board, as this may result in unforeseen operation of the device, fire or electric shock.
Terminal marking on the PC-4000 board:
MAIN CONNECTOR:
+12V Positive power supply
GND Supply earth voltage
SERB Communication series B
SERA Communication series A
SPK Audio speaker signal
MIC Audio sound microphone
CONNECTOR OF ELECTRIC STRIKES:
GND Electric strikes ground
LOCK1 Main electric strike
LOCK2 Additional electric strike
GND Additional button ground
WZ Additional button

~3~
2. GENERAL
The front panel is made of acid-proof weather-resistant metal sheet. The casing, however, is made of galvanized
steel.
Integrated energy-saving RFID UNIQUE 125kHz proximity card reader
Fully metal backlit keyboard
Large LCD alphanumeric display with backlight
Heated display
Light sensor
Backlight operation in day/night mode
Camera angle adjustment in the range of +/- 20 degrees
Control of two electric strikes independently
Possibility of settings change from the GC-2000 programmer
Installer LOGO
3. INSTALLATION
If possible, the panel should be installed in places not exposed to weather conditions, such as rain or snow.
After forging the opening in the building wall or a fixed door leaf, the bottom of the intercom entry access panel
should be fixed with 4 screws with raw plugs by inserting them through the 4 holes in the bottom part of the entry
access panel. Dimensions of the bottom of the entry access panel - Height 255mm, Width 83mm, Depth 35mm.
Large openingsare designed forrouting cables connecting the entry system panel with the electronicmodule ofthe
control panel.
The front panel, after attaching the cover (visor) and sliding it into the bottom part of the system installed on the wall,
is screwed with two M4 TORX20 screws with a pin.
Avoiding external installation of the system by installing it inside the building (vestibule, windscreen) if possible.
Severely soiling the keypad (snow, mud) or wetting it may cause interference in its operation.
In the base of the flush-mounted box there is a M4 threaded pin to which a protective conductor
(ground) must be connected. If the panel is broken or non-grounded, a person may be
electrocuted by the call panel.

~4~
4. CONNECTING
For correct operation thepanel requires connection toCC-4000 control electronics. A detailed description can
be found in the manual for the CC-4000 board.
Connection of electro strike and output button on the figure below:
The main strike can be a jumper/strike/reversing strike with a maximum current consumption of up to 750mA.
After exceeding the maximum current, the panel will automatically disconnect this output.
The output button serves as an additional button that releases the main strike, it is a regular button.
'STRIKE2' is a current output without galvanic isolation, therefore it can control other devices only through an
additional relay. Its load capacity is 250mA.
It should be noted that the housing of the panel is not a supply ground!
The panel can be powered from the CC-4000 electronics board or its own DC power supply (see the CC4000
system manual)
Below is the photo with the description of the connectors:
OUTPUT BUTTON
STRIKE2
MAIN STRIKE

~5~
Camera angle
adjustment
Symmetrical
camera
connector
Panel serial
number
Connector of
the programmer
Main
connector
Connector
of the electric
strikes

~6~
It should be noted that the main connectorand the connector of the electric strikes are of the detachable
type. Below is the figure with the connector inserted and removed. The connectors are inserted by
pressing-in.
5. PROGRAMMING
A complete description of the programming procedure can be found in the manual for the CC4000 system, but the
functions related to the PC-4000 panel itself will be described below.
Each panel is protected by a password which is factory set to 123456. To start the programming procedure, enter
thefollowing onthe enabled panel in standby mode: *01*, then 6-digit panel serial number, confirm with '*' and enter
the password, and confirm with '*'. So, for example, for the panel of serial no. 150000 and password 123456, enter
the sequence *01*150000*123456*.
All P01 program sub-programmes relate to the panel memory, such as configurations of electric strikes, pairing with
the control panel (SLAVE panel), changing the password, number range, service key fobs and sub-program 10 for
reading the supply voltage, lighting and CPU temperature.
The LOGO consists of four sequences of 8 characters changed every 2 seconds. Its change is possible only from
the programmer. Reset to factory settings of the panel does not change the LOGO!
Below are examples of settings programmed using the GC-2000 programmer

~7~
It is not possible to change the serial number with the programmer!
If you connect the programmer to the panel that is already part of the entry system installation, first connect the
programmer to the panel board, and then the programmer to the USB connector. Otherwise, the board or
programmer may be damaged due to possible overvoltages.
No power is required on the panel board to program or download settings from memory.
6. CAMERA MODULE
The camera consists of a 1/3 "colour CMOS sensor with a lens of an angle of view of 110 degrees and a video
signal balun and illuminator with infrared LEDs.
The angle of view of the camera can be adjusted within the 20 degree horizontal and 15 degrees vertical range.
Three nylon nuts are used for adjustment. During adjustment, special care should be taken so that the lens does
not rest on transparent polycarbonate. In addition, the nuts should not "go beyond" the threaded pins.

~8~
The cables that transmit the video signal are connected to the symmetrical connector of the camera. The
left 'H' terminal is a non-inverted signal in the phase. The right terminal is inverted in the phase by 180
degrees. The middle terminal is the signal ground of the video.
The camera should be connectedto appropriate terminals inthe CC-4000 control electronics (SLAVEor MASTER,
depending on the panel configuration)
7.OTHER
Pressing the '#' key in the idle mode will refresh the settings and restart the LCD display. This can be helpful in
situations when the display will 'freeze' due to an electrical breakdown or incorrect operation.
Heating of the LCD display turns on when the temperature inside the panel housing drops below 5 degrees
Celsius. The heater has an additional protection against overheating the display. Heating power is about 3W.
The panel is equipped with a protection against reverse polarity, overvoltage, overcurrent.
A short circuit in any electric strike channel does not immobilize the system and should not damage any element.
After the short circuit, the panel is fully functional
Technical data of the device:
Supply voltage ...............................................12-13.8V DC stabilized
Average current in PC-4000...........................about 70mA
LCD heater power consumption.....................250mA
Strikes max. power consump.........................750mA
Camera power consump................................about 100mA
IR illuminator power consump. ......................30mA
PC-4000 board max. current..........................1.2A
Dimensions....................................................270x100x33mm
Overcurrent protection ...................................2.5A
Transmission speed RS-485..........................3kbps
IR illuminator wavelength ..............................850nm
RFID frequency................................................125kHz
Max. speaker power.......................................0.5W