Cyfral VIDEOMONITOR V4 Assembly instructions

Page 1
VIDEOMONITOR V4
OPERATING, INSTALLATION AND PROGRAMMING MANUAL

Page 2
INTRODUCTION
Before installing the device, read the following operating instructions. Installation may onlybe carriedout bya
qualified person with the adequate qualifications.
This manual applies to the V4 Videomonitor which is part of the CC4000 system. The description of
programming and connecting with the rest of the system elements can be found in the CC4000 System
Manual.
Videomonior and devices connected to it are only allowed to be powered with extra-low voltage (ELV) with a
value not exceeding the allowable safe contact voltage. Power devices (12V DC power supplies) must
comply with EMC and safety standards in accordance with applicable European Union standards and ensure
full galvanic isolation from the power grid.
Fig. 1 View of the videomonitor connectors
DESCRIPTION
OF
CONNECTOR
S
Zasilanie
12V power supply from a local power supply or DV-4 distributor
IN
Socket for connecting the DV-4 distributor
OUT
Socket for connecting another monitor
CAM1
Additional camera input 1
CAM2
Additional camera input 2

Page 3
DESCRIPTION OF THE BUTTONS:
- Receiving / ending a call
- Preview from the camera at the entrance
- Opening of the electro strike
- Call forwarding or internal call
Multifunction
button
Volume
adjustment

Page 4
Installation
Fig. 2 Installation of the monitor
Monitor should be installed away from devices emitting electromagnetic interference, i.e. all kinds of
switched-mode power supplies, chargers, computers.
If possible, the monitor should be installed in places not exposed to moisture, too high or too low temperature.

Page 5
SETTINGS
After pressing the multifunction button , the idle mode menu will appear. To navigate through the
settings, turn the multifunctional button up/down. To confirm selected fields, press the multifunctional button.
The settings consist of the following groups:
1. SYSTEM:
•Language - You can choose between Polish, English, Chinese
•Time - Current time and date
•Advanced- Information regarding the device, file management
2. SOUND:
•Selecting a ringtone - selecting the incoming call melody between 1 and 10
•Ringtone volume- selection of ringtone volume depending on the time of day
3. SETTINGS:
•Mode - in the CC4000 system, absolutely Slave
•Audio/video record mode - recording of the call on the SD card
•Support of input 2 - Does not apply in CC4000
•Opening Times - Does not apply in CC4000
•Motion detection - Does not apply in CC4000
•Messages - Does not apply in CC4000
4. ALARM:
•For the monitor operating as Slave inactive
5. DISPLAY:
•Settings of brightness, contrast and colour saturation of the image
6. FILES:
•File browser for files saved on the SD card of the device
INTERCOM
V4 monitors can be cascaded up to three pieces per one property. The incoming call to the property will be
visible and audible on all, up to three, monitors. Answering a call on one of them will cause the other to turn
off. However, during a call, pressing the "intercom" button allows you to redirect the conversation to other
monitors.
In addition, pressing the "intercom" button in idle mode will allow you to conduct an internal call.

Page 6
The monitors are connected with the "IN" and "OUT" connectors. The first monitor is connected to the
distributor via the "IN" connector. From the first monitor from the "OUT" connector the cable is routed to the
"IN" connector of the next monitor.
Fig. 3 Connecting multiple monitors within one property
When connecting monitors in accordance with Figure 3, each monitor should be powered from a separate
source.

Page 7
Technical data of the device:
Supply voltage ......................................................................12-13.8V DC stabilized
Maximum current consumption in idle mode .........................250mA
Maximum power consumption during operation... ................600 mA
Working temperature.............................................................0-50°C
Display .................................................................................4" LCD TFT
Screen resolution..................................................................320x240
Standard........................................................................... ...PAL/NTSC
Recording format ..................................................................JPEG
External memory...................................................................SD card maks. 32GB Class >9