d & b audiotechnik Z5402 User manual

ZZ5402/03
Mounting instructions 1.1 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
Z5402/03 Mounting instructions
Version: 1.1 en, 08/2011, D2957.EN .01
Copyright © 2011 by d&b audiotechnik GmbH & Co. KG; all
rights reserved.
Keep these mountings instructions with the product or
in a safe place so that they are available for future
reference.
When reselling this product, hand over this document to the new
owner.
d&b audiotechnik GmbH & Co. KG
Eugen-Adolff-Str. 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

1 Z5402/Z5403 Wall mount M/L...................................... 4
1.1 Scope of supply.......................................................................... 4
1.2 Safety precautions...................................................................... 4
1.3 Intended use................................................................................ 4
1.4 Mounting options........................................................................ 5
1.5 Assembly..................................................................................... 5
1.6 Vertical and horizontal alignment.............................................. 6
2 Fixing templates................................................................... 7
2.1 Vertical setup............................................................................... 7
2.2 Horizontal setup.......................................................................... 8
3 Built-in dimensions............................................................... 9
3.1 Wall mount M/L ........................................................................ 9
3.2 8S loudspeaker........................................................................ 10
3.3 10S/10S-D loudspeaker......................................................... 12
3.4 12S/12S-D loudspeaker......................................................... 14
4 Declarations......................................................................... 16
4.1 Manufacturer's declaration...................................................... 16
4.2 Disposal.................................................................................... 16
Contents
d&b Z5402/03 Mounting instructions 1.1 en 3

1.1 Scope of supply
Please verify the shipment for completeness and proper condition
of the items.
Qty. d&b Code Description
1Z5402 d&b Wall mount M [1] (a)
1Z5403 d&bWall mount L [1] (b)
Each including:
2 Hex head bolt M8 x 20 [2]
2 Spring washer [3]
1 D2957.EN .01 Mounting instructions
Weight Wall mount M 1.3 kg / 2.9 lb
Weight Wall mount L 1.4 kg / 3.1 lb
1.2 Safety precautions
General safety
Installation and setup should only be carried out by qualified and
authorized personnel observing the valid national Rules for the
Prevention of Accidents (RPA).
It is the responsibility of the person installing the assembly to ensure
that the suspension/fixing points are suitable for the intended use.
Always carry out a visual and functional inspection of the items
before use. In case you have any doubt as to the proper
functioning and safety of the items, these must be withdrawn from
use immediately.
Load safety information
The maximum permitted working load of the Z5402 Wall mount M
and Z5403 Wall mount L is 17 kg (37 lb) (according to BGV C1)
which implies the weight of one 8S/10S/10S-D/12S or 12S-D
cabinet.
1.3 Intended use
The d&b Z5402 Wall mount M and Z5403 Wall mount L must
only be used in conjunction with the d&b xS-Series loudspeakers
8S, 10S/10S-D and 12S/12S-D as described in these mounting
instructions.
The wall mounts allow both horizontal or vertical mounting of the
cabinets as well as vertical and horizontal alignment.
Scope of supply
1 Z5402/Z5403 Wall mount M/L
d&b Z5402/03 Mounting instructions 1.1 en4

1.4 Mounting options
Mounting options
The tilt unit [6] of the wall mount can be rotated through 90°
allowing the cabinet to be mounted either vertically (a) or
horizontally (b).
To change the orientation of the tilt unit, proceed as follows:
Tools required:
▪ Open-ended spanner/wrench (size #13)
▪ Allen hex key (6 mm)
1. Slacken and undo the self-securing nut [1] and remove the
fixing bolt [2].
2. Remove the tilt unit [3] and turn it through 90°.
3. Refit the tilt unit in reverse order.
1.5 Assembly
Mounting plate
NOTICE!
Only use mounting parts (fixing anchors and screws) that are
suitable for the intended application.
Observe the occurring extraction forces acting on the fixing
anchors and screws. The rated extraction force is 350 N.
A corresponding fixing template is supplied with these mounting
instructions. Refer to Þ Chapter 2 "Fixing templates" on page 7.
An additional 20 mm (0.8") centered hole is provided on the
mounting plate as a feed-through for the connection cable. The
cable can be fed through the mounting plate into the boom arm
that acts as a cable run.
Attaching the cabinet to the wall mount
NOTICE!
▪ Only use the supplied and specified screws [2], otherwise there
a risk of damaging the threaded inserts.
▪ Always use the supplied spring washers [3] to prevent the bolts
from slackening.
Tools required:
▪ Open-ended spanner/wrench (size #13)
1. Attach the wall mount to the two M8 threaded inserts on the
rear panel of the cabinet.
2. Insert the screws together with the spring washers and tighten
them.
d&b Z5402/03 Mounting instructions 1.1 en 5

1.6 Vertical and horizontal alignment
The wall mounts allow both vertical and horizontal alignment of the
cabinets. The possible vertical and horizontal angle settings
depend on the cabinet size, the deployment of the cabinets
(vertical or horizontal setup) and the type of wall mount used. The
various options and angle settings including the built-in dimensions
are detailed in Þ Chapter 2 "Fixing templates" on page 7.
Tools required:
▪ Open-ended spanner/wrench (size #13)
▪ Allen hex key (6 mm).
Vertical alignment
The wall mounts are equipped with a stop screw [B] to allow a
precise vertical alignment of the cabinet.
1. Slacken the stop screw [B].
2. Slightly slacken the fixing bolt [F].
3. Set the cabinet to the desired vertical angle.
4. Adjust the stop screw [B] until the desired angle is finally set.
5. Tighten the counter nut [C] to fix the adjustment.
6. Retighten the fixing bolt.
Horizontal alignment
1. Slightly slacken the fixing bolt [F].
2. Set the cabinet to the desired horizontal angle.
3. Retighten the fixing bolt.
d&b Z5402/03 Mounting instructions 1.1 en6

2.1 Vertical setup
Z5402/03 Wall mount M/L, fixing template vertical setup,
shown with center ( ) of the 8S, 10S/10S-D and 12S/12S-Dcabinets.
2 Fixing templates
d&b Z5402/03 Mounting instructions 1.1 en 7

2.2 Horizontal setup
Z5402/03 Wall mount M/L, fixing template horizontal setup,
shown with center ( ) of the 8S, 10S/10S-D and 12S/12S-Dcabinets.
d&b Z5402/03 Mounting instructions 1.1 en8

3.1 Wall mount M/L
Z5402/03 Wall mount M/L dimensions in mm [inch]
3 Built-in dimensions
d&b Z5402/03 Mounting instructions 1.1 en 9

3.2 8S loudspeaker
Z5402 Wall mount M, built-in dimensions in mm [inch], 8S vertical setup
Z5402 Wall mount M, built-in dimensions in mm [inch], 8S horizontal setup
d&b Z5402/03 Mounting instructions 1.1 en10

Z5403 Wall mount L, built-in dimensions in mm [inch], 8S vertical setup
Z5403 Wall mount L, built-in dimensions in mm [inch], 8S horizontal setup
d&b Z5402/03 Mounting instructions 1.1 en 11

3.3 10S/10S-D loudspeaker
Z5402 Wall mount M, built-in dimensions in mm [inch],10S/10S-D vertical setup
Z5402 Wall mount M, built-in dimensions in mm [inch], 10S/10S-D horizontal setup
d&b Z5402/03 Mounting instructions 1.1 en12

Z5403 Wall mount L, built-in dimensions in mm [inch], 10S/10S-D vertical setup
Z5403 Wall mount L, built-in dimensions in mm [inch], 10S/10S-Dhorizontal setup
d&b Z5402/03 Mounting instructions 1.1 en 13

3.4 12S/12S-D loudspeaker
Z5402 Wall mount M, built-in dimensions in mm [inch],12S/12S-D vertical setup
Z5402 Wall mount M, built-in dimensions in mm [inch], 12S/12S-D horizontal setup
d&b Z5402/03 Mounting instructions 1.1 en14

Z5403 Wall mount L, built-in dimensions in mm [inch], 12S/12S-D vertical setup
Z5403 Wall mount L, built-in dimensions in mm [inch], 12S/12S-D horizontal setup
d&b Z5402/03 Mounting instructions 1.1 en 15

4.1 Manufacturer's declaration
This declaration covers:
▪ d&b Z5402,Wall mount M.
▪ d&b Z5403 Wall mount L.
National standards and technical specifications
applied:
DIN 18 800, DIN 1055, DGUV Vorschrift 17, BGI 810-3.
Backnang, 2011-08-24
Frank Bothe,
Chief Technology Officer (CTO)
d&baudiotechnik GmbH & Co.
KG
4.2 Disposal
When out of use the rigging components must be disposed of in
accordance with the national environmental regulations.
Ensure that damaged rigging components are disposed of in a
way that they cannot be used again.
4 Declarations
d&b Z5402/03 Mounting instructions 1.1 en16

D2957.EN .01, 08/2011 © d&b audiotechnik GmbH & Co. KG
www.dbaudio.com