d & b audiotechnik M2 User manual

MM2
Manual 5.1 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
M2 Manual
Version: 5.1 en, 11/2016, D2092.EN .05
Copyright © 2016 by d&b audiotechnik GmbH; all rights
reserved.
Keep this manual with the product or in a safe place
so that it is available for future reference.
When reselling this product, hand over this manual to the new
owner.
If you supply d&b products, please draw the attention of your
customers to this manual. Enclose the relevant manuals with the
systems. If you require additional manuals for this purpose, you
can order them from d&b.
d&b audiotechnik GmbH
Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

1. Safety precautions........................................................... 4
1.1. Information regarding the use of loudspeakers.................... 4
2. M2 loudspeaker............................................................... 5
2.1. Product description.................................................................. 5
2.2. Connections............................................................................. 5
2.3. Operation................................................................................ 6
2.3.1. Controller settings................................................................ 6
2.3.2. Operation with A1............................................................... 7
2.4. Dispersion characteristics........................................................ 7
2.5. Technical specifications.......................................................... 8
3. Manufacturer's declarations....................................... 9
3.1. EU conformity of loudspeakers (CE symbol)......................... 9
3.1.1. WEEE Declaration (Disposal)............................................. 9
Contents
d&b M2 Manual 5.1 en 3

1.1. Information regarding the use of loudspeakers
Potential risk of personal injury
Never stand in the immediate vicinity of loudspeakers driven at a
high level. Professional loudspeaker systems are capable of
causing a sound pressure level detrimental to human health.
Seemingly non-critical sound levels (from approx. 95 dB SPL) can
cause hearing damage if people are exposed to it over a long
period.
In order to prevent accidents when deploying loudspeakers on the
ground or when flown, please take note of the following:
– When setting up the loudspeakers or loudspeaker stands,
make sure they are standing on a firm surface. If you place
several systems on top of one another, use straps to secure
them against movement.
– Only use accessories which have been tested and approved
by d&b for assembly and mobile deployment. Pay attention to
the correct application and maximum load capacity of the
accessories as detailed in our specific "Mounting instructions"
or in our "Flying system and Rigging manuals".
– Ensure that all additional hardware, fixings and fasteners used
for installation or mobile deployment are of an appropriate
size and load safety factor. Pay attention to the manufacturers'
instructions and to the relevant safety guidelines.
– Regularly check the loudspeaker housings and accessories for
visible signs of wear and tear, and replace them when
necessary.
– Regularly check all load bearing bolts in the mounting devices.
Potential risk of material damage
Loudspeakers produce a static magnetic field even if they are not
connected or are not in use. Therefore make sure when erecting
and transporting loudspeakers that they are nowhere near
equipment and objects which may be impaired or damaged by an
external magnetic field. Generally speaking, a distance of 0.5 m
(1.5 ft) from magnetic data carriers (floppy disks, audio and video
tapes, bank cards, etc.) is sufficient; a distance of more than 1 m
(3 ft) may be necessary with computer and video monitors.
1. Safety precautions
d&b M2 Manual 5.1 en4

2.1. Product description
The M2 is a is a 2-way active high performance loudspeaker for
stage monitoring purposes. The bass-reflex enclosure is optimized
for minimal air compression and houses two 12" LF drivers. It is
actively crossed over and powered by both channels of an
appropriate d&b amplifier. The 1.4" exit HF compression driver
has a compact but strong neodymium magnet assembly operating
into a very low distortion waveguide oriented horn, optimized for
monitor applications.
The component configuration permits the use of an low profile
cabinet which achieves a constant directivity from an unusually low
frequency of 600 Hz upwards with a nominal dispersion of 45° x
60° (h x v). Together with a cabinet baffle angle of 40° to the
floor, this dispersion offers a realistic artist listening area starting
directly above the cabinet and ranging quite far upstage.
The cabinet is constructed from marine plywood and has an impact
resistant paint finish. The front of the loudspeaker cabinet is fitted
with a rigid metal grill backed with a replaceable acoustically
transparent foam. Each side panel incorporates a handle while two
runners are recessed in the bottom panel to prevent cabinet
movement and protect the bottom panel against scratching.
In addition two sockets which accept the Z5048 Flying pin 10 mm
are located on both side panels of the cabinet allowing quick and
flexible rigging.
2.2. Connections
The cabinet is fitted with NLT4 F/M connectors. All four pins of
both connectors are wired in parallel using the pin assignments
1+/1– (LF) and 2+/2– (HF). Using one connector as the input, the
second connector allows for direct connection to a second cabinet.
The cabinet can be supplied with EP5 or NL8 connectors as an
option.
Pin equivalents of the connector options are listed in the table
below.
LF + LF – HF + HF – SenseDrive
NLT4 F/M 1+ 1– 2+ 2– n.a.
EP5 1 2 3 4 5
NL8 1+ 1– 4+ 4– 3–
d&b LoadMatch
With the d&b four channel amplifier platform, the LoadMatch
function enables the amplifier to electrically compensate for the
properties of the loudspeaker cable used without the need for an
additional sense wire. For applicable loudspeakers, LoadMatch is
therefore independent of the connector type used.
Z5048 Flying pin 10 mm
NLT4 F/M and EP5 connector wiring
2. M2 loudspeaker
d&b M2 Manual 5.1 en 5

d&b SenseDrive
The SenseDrive feature within D12 amplifiers enables electrical
compensation for the properties of the loudspeaker cable used.
SenseDrive requires an additional sense wire. SenseDrive is
therefore only available with EP5 connectors and 5-wire cabling
for applicable loudspeakers.
Note: To enable SenseDrive for the LF drivers, the
loudspeaker cabinet has to be connected to the output A
connector. For two cabinets, they should be linked together
locally and then connected to the output A connector.
2.3. Operation
NOTICE!
Only operate d&b loudspeakers with a correctly configured d&b
amplifier, otherwise there is a risk of damaging the loudspeaker
components.
Applicable d&b amplifiers:
D80/D12/30D.
Application Setup Cabinets per
pair of amplifier
channels
M2 M2 2
For applicable d&b amplifiers, the controller setup is available in
2-Way Active mode.
2.3.1. Controller settings
For acoustic adjustment the functions CUT and CPL can be
selected.
CUT mode
Set to CUT, a high pass filter with a 110 Hz cut off frequency is
inserted in the controller signal path. The M2 is now configured for
use with actively driven d&b subwoofers.
CPL function
The CPL (Coupling) function compensates for coupling effects
between the cabinets when building closely coupled arrays. CPL
begins gradually around 1 kHz, with the maximum attenuation
below 400 Hz providing a balanced frequency response when the
M2 cabinet is used in arrays of two or more. To achieve a
balanced frequency response, the CPL function can be set to dB
attenuation values between 0 and –9.
Positive CPL values create an adjustable low frequency boost
around 65 Hz (0 to +5 dB).
The following CPL settings correspond to the M2 controller settings
of the A1 and are described in the following section Þ "Operation
with A1 - LFC level control":
0 dB = Floor, +3 dB = Free, –3 dB = Pair
INPUT A OUT A
2-Way
SenseDrive
OUT B
2-Way
AMP B
AMP A
D12 Input/Output routing 2-Way Active mode
Frequency response correction of the CPL function
d&b M2 Manual 5.1 en6

2.3.2. Operation with A1
Two M2 cabinets can be driven by a single A1 mainframe fitted
with an M2 controller module.
CUT switch
The CUT setting is available. The characteristics of the CUT setting
is described in the previous section Þ "Controller settings - CUT
mode".
LF Coupling level control
The LF Coupling level control (Low Frequency Coupling) adjusts
the systems low and low/mid response for the different operating
environments of the M2 cabinet.
The FLOOR position is the standard setting for a single M2, used
as a floor monitor.
Turning the control to the PAIR position, the low and lower/mid
frequency range is further reduced (Corner frequency about
600 Hz). The maximum left position fully compensates the different
coupling behaviour of the low and high frequencies when two
cabinets are used in a paired monitor application.
Turning towards FREE increases the systems low end for operation
without floor coupling (e.g. flown).
2.4. Dispersion characteristics
The diagrams below show dispersion angle vs frequency plotted
using lines of equal sound pressure (isobars) at –6 dB and
–12 dB. The nominal 45° horizontal dispersion angle is
maintained from 800 Hz - 10 kHz.
M2 isobar diagram vertical
10 100 1k 10k
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
FREE
PAIR
Controls on M2 controller module.
Frequency response LFC setting (min. and max.)
M2 isobar diagram horizontal
d&b M2 Manual 5.1 en 7

2.5. Technical specifications
M2 system data
Frequency response (–5 dB standard) 57 Hz - 17 kHz
Frequency response (–5 dB, floor coupling ) 50 Hz - 17 kHz
Max. sound pressure (1 m, free field)
with D80 143 dB
with D12 143 dB
with 30D 143 dB
(SPLmax peak, pink noise test signal with crest factor of 4)
M2 loudspeaker
Nominal impedance LOW/HIGH 4/8 ohms
Power handling capacity LOW (RMS / peak 10 ms) 500/2000 W
Power handling capacity HIGH (RMS / peak 10 ms) 50/200 W
Nominal dispersion angle (h x v) 45° x 60°
Components 2 x 12" LF driver with neodymium magnet
1.4" exit compression driver with CD horn
Connections NLT4 F/M
optional 2 x EP5 or NL8
Pin assignment
NLT4 F/M: LF +/–: 1+/1– | HF +/–: 2+/2–
EP5: 1: LF+ | 2: LF– | 3: HF+ | 4: HF– | 5: SenseDrive
NL8: LF +/–: 1+/1– | HF +/–: 4+/4– | SenseDrive: 3–
Weight 38 kg (83 lb)
M2 cabinet dimensions in mm [inch]
M2 frequency response, listening position in monitor operation
Measured on axis at a height of 1.7 m (5.6 ft)
d&b M2 Manual 5.1 en8

3.1. EU conformity of loudspeakers (CE symbol)
This declaration applies to:
d&b M2 loudspeaker, Z0061
manufactured by d&b audiotechnik GmbH.
All production versions of these types are included, provided they
correspond to the original technical version and have not been
subject to any later design or electromechanical modifications.
We herewith declare that said products are in conformity with the
provisions of the respective EC directives including all applicable
amendments.
A detailed declaration is available on request and can be ordered
from d&b or downloaded from the d&b website at
www.dbaudio.com.
3.1.1. WEEE Declaration (Disposal)
Electrical and electronic equipment must be disposed of separately
from normal waste at the end of its operational lifetime.
Please dispose of this product according to the respective national
regulations or contractual agreements. If there are any further
questions concerning the disposal of this product, please contact
d&b audiotechnik.
3. Manufacturer's declarations
d&b M2 Manual 5.1 en 9

D2092.EN .05, 11/2016 © d&b audiotechnik GmbH
www.dbaudio.com