d & b audiotechnik Y7P User manual

YY7P/Y10P
Manual 1.2 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
Y7P/Y10P Manual
Version: 1.2 en, 03/2016, D2710.EN .01
Copyright © 2016 by d&b audiotechnik GmbH; all rights
reserved.
Keep this manual with the product or in a safe place
so that it is available for future reference.
When reselling this product, hand over this manual to the new
owner.
If you supply d&b products, please draw the attention of your
customers to this manual. Enclose the relevant manuals with the
systems. If you require additional manuals for this purpose, you
can order them from d&b.
d&b audiotechnik GmbH
Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

1. Safety precautions........................................................... 4
1.1. Information regarding the use of loudspeakers.................... 4
2. Y7P/Y10P loudspeaker................................................. 5
2.1. Product description.................................................................. 5
2.2. Connections............................................................................. 6
2.3. Operation................................................................................ 6
2.3.1. Controller settings................................................................ 6
2.4. Dispersion characteristics........................................................ 8
2.5. Technical specifications........................................................ 10
3. Manufacturer's declarations..................................... 11
3.1. EU conformity of loudspeakers (CE symbol)....................... 11
3.1.1. WEEE Declaration (Disposal)........................................... 11
Contents
d&b Y7P/Y10P Manual 1.2 en 3

1.1. Information regarding the use of loudspeakers
Potential risk of personal injury
Never stand in the immediate vicinity of loudspeakers driven at a
high level. Professional loudspeaker systems are capable of
causing a sound pressure level detrimental to human health.
Seemingly non-critical sound levels (from approx. 95 dB SPL) can
cause hearing damage if people are exposed to it over a long
period.
In order to prevent accidents when deploying loudspeakers on the
ground or when flown, please take note of the following:
– When setting up the loudspeakers or loudspeaker stands,
make sure they are standing on a firm surface. If you place
several systems on top of one another, use straps to secure
them against movement.
– Only use accessories which have been tested and approved
by d&b for assembly and mobile deployment. Pay attention to
the correct application and maximum load capacity of the
accessories as detailed in our specific "Mounting instructions"
or in our "Flying system and Rigging manuals".
– Ensure that all additional hardware, fixings and fasteners used
for installation or mobile deployment are of an appropriate
size and load safety factor. Pay attention to the manufacturers'
instructions and to the relevant safety guidelines.
– Regularly check the loudspeaker housings and accessories for
visible signs of wear and tear, and replace them when
necessary.
– Regularly check all load bearing bolts in the mounting devices.
Potential risk of material damage
Loudspeakers produce a static magnetic field even if they are not
connected or are not in use. Therefore make sure when erecting
and transporting loudspeakers that they are nowhere near
equipment and objects which may be impaired or damaged by an
external magnetic field. Generally speaking, a distance of 0.5 m
(1.5 ft) from magnetic data carriers (floppy disks, audio and video
tapes, bank cards, etc.) is sufficient; a distance of more than 1 m
(3 ft) may be necessary with computer and video monitors.
1. Safety precautions
d&b Y7P/Y10P Manual 1.2 en4

2.1. Product description
Y7P/Y10P are passive 2-way loudspeakers housing two 8" LF
drivers and a 1.4" HF compression driver with a rotatable CD horn
producing a nominal dispersion (h x v) of 75° x 40° or 110° x
40°, respectively. The frequency response extends from 59 Hz to
above 18 kHz.
The two 8" neodymium LF drivers are positioned in a dipolar
arrangement providing exceptional vertical dispersion control even
at lower frequencies.
Specially designed ports with optimized flow characteristics
provide a considerably improved, efficient low frequency
reproduction.
The cabinets are constructed from marine plywood and have an
impact and weather protected PCP (Polyurea Cabinet Protection)
finish. The top and bottom panels incorporate a handle each. The
front of the loudspeaker cabinet is protected by a rigid metal grill
backed by an acoustically transparent foam.
The cabinets accommodate fittings for three types of rigging
devices:
– A quick lock adapter plate on one side of the cabinet that
accepts the Z5397 YP Swivel bracket.
– Two M10 threaded inserts on the top and bottom panels each
to accept the Z5399 YP Mounting bracket.
– Two additional combined sockets [A], one in the top panel
and one at the center rear of the cabinet that accept either:
– the Q9032 Safety eye bolt M10 to apply a secondary
safety device.
– the Z5049 Flying pin 8 mm to support single cabinets or to
secure the aiming of an array.
Intended use of the Z5049 Flying pin
WARNING!
Potential risk of personal injury and/or
damage to material!
The Z5049 Flying pin 8 mm is designed and intended for static
loads only. Therefore please observe the following:
– The Flying pin must not be used to attach a secondary safety
device.
– Ensure the Flying pin is securely locked before lifting any load.
Proceed as follows:
1. Press the button to release the locking mechanism ([r] ).
2. Fully insert the Flying pin into the respective socket.
3. Release the button to lock the pin ([l] ).
4. Recheck the Flying pin is securely locked by briefly pulling the
Flying pin towards you.
Additional combined sockets
2. Y7P/Y10P loudspeaker
d&b Y7P/Y10P Manual 1.2 en 5

2.2. Connections
The cabinets are fitted with a pair of NLT4 F/M connectors. All
four pins of both connectors are wired in parallel. The cabinets use
the pin assignments 1+/1–. Pins 2+/2– are designated to active
subwoofers. Using the male connector as the input, the female
connector allows for direct connection to a second cabinet.
The cabinets can be supplied with NL4 M or EP5 connectors as an
option.
Pin equivalents of the connector options are listed in the table
below.
NLT4 F/M
NL4 M 1+ 1– 2+ 2– n.a.
EP5 1 2 3 4 5
2.3. Operation
NOTICE!
Only operate d&b loudspeakers with a correctly configured d&b
amplifier, otherwise there is a risk of damaging the loudspeaker
components.
Applicable d&b amplifiers:
D80/D20/D12/D6/10D/30D.
Application Setup Cabinets per
channel
Y7P Y7P 2
Y10P Y10P 2
For applicable amplifiers, the controller setups are available in
Dual Channel and Mix TOP/SUB mode.
2.3.1. Controller settings
For acoustic adjustment the functions CUT, HFA and CPL can be
selected.
CUT circuit
Set to CUT, the cabinet low frequency level is reduced. The
cabinets are now configured for use with actively driven d&b
subwoofers.
passive
crossover
Connector wiring
d&b Y7P/Y10P Manual 1.2 en6

HFA circuit
In HFA mode (High Frequency Attenuation), the HF response of the
system is rolled off. HFA provides a natural, balanced frequency
response when a unit is placed close to listeners in near field or
delay use.
High Frequency Attenuation begins gradually at 1 kHz, dropping
by approximately 3 dB at 10 kHz. This roll off mimics the decline
in frequency response experienced when listening to a system from
a distance in a typically reverberant room or auditorium.
CPL circuit
The CPL (Coupling) circuit compensates for coupling effects
between the cabinet and close boundary surfaces. CPL begins
gradually around 1 kHz, with the maximum attenuation below
400 Hz. To achieve a balanced frequency response, the CPL
circuit can be set to dB attenuation values between 0 and –9.
Positive CPL values create an adjustable low frequency boost (0 to
+5 dB) at around 65 Hz and can be set when the system is used in
full range mode without subwoofers.
-5
0
5
10
-10
-15
-20
-25
-30
20 100 1k 10k 20k
Frequency response correction of HFA circuit
Frequency response correction of CPL circuit
d&b Y7P/Y10P Manual 1.2 en 7

2.4. Dispersion characteristics
The following graphs show dispersion angle over frequency of a
single cabinet plotted using lines of equal sound pressure (isobars)
at –6 dB and –12 dB.
Isobar diagram horizontal
Y7P
vertical setup
Isobar diagram vertical
Isobar diagram horizontal
Y7P
horizontal setup,
horn rotated
Isobar diagram vertical
d&b Y7P/Y10P Manual 1.2 en8

Isobar diagram horizontal
Y10P
vertical setup
Isobar diagram vertical
Isobar diagram horizontal
Y10P
horizontal setup,
horn rotated
Isobar diagram vertical
Altering the HF horn dispersion
By factory default, the HF horn is fitted to the cabinet providing the
nominal horizontal dispersion when the cabinet is used in upright
position. This is indicated by a white label on the horn flange. The
label is visible through the front grill on each side of the cabinet as
shown in the graphic opposite.
The HF horn can be rotated through 90°.
Tools required: Torx wrench (#TX20).
1. Undo the torx screws on the top and bottom panels of the
cabinet and remove the front grill.
2. Undo the screws holding the horn flange and rotate the horn.
3. Refit the horn as follows:
– Make sure the gasket of the horn is in place.
– Refit the horn.
– Insert all screws and carefully tighten them clockwise until
they fit precisely into the countersunk holes.
4. Refit the front grill.
Altering the HF dispersion
d&b Y7P/Y10P Manual 1.2 en 9

2.5. Technical specifications
Y7P/Y10P system data
Frequency response (–5 dB standard) 59 Hz - 18 kHz
Frequency response (–5 dB CUT mode) 118 Hz - 18 kHz
Max. sound pressure (1 m, free field)
Y7P with D6/10D 132 dB
Y7P with D12/D20/30D 135 dB
Y7P with D80 137 dB
Y10P with D6/10D 131 dB
Y10P with D12/D20/30D 134 dB
Y10P with D80 136 dB
(SPLmax peak, pink noise test signal with crest factor of 4)
Y7P/Y10P loudspeaker
Nominal impedance 8 ohms
Power handling capacity (RMS/peak 10 ms) 400/1600 W
Nominal dispersion angle (horizontal) Y7P 75°
Nominal dispersion angle (horizontal) Y10P 110°
Nominal dispersion angle (vertical) 40°
Components 2 x 8" driver with neodymium magnet
1.4 ” exit compression driver
Passive crossover network
Connections 2 x NLT4 F/M
optional 2 x NL4 M or EP5
Pin assignment NLT4 F/M and NL4 M: 1+/1–
EP5: 1: + / 2: –
Weight 18 kg (40 lb)
Y7P/Y10P cabinet dimensions in mm [inch]
Y7P frequency response, standard and CUT modes
Y10P frequency response, standard and CUT modes
d&b Y7P/Y10P Manual 1.2 en10

3.1. EU conformity of loudspeakers (CE symbol)
This declaration applies to:
d&b Y7P loudspeaker, Z0702
d&b Y10P loudspeaker, Z0703
manufactured by d&b audiotechnik GmbH.
All production versions of these types are included, provided they
correspond to the original technical version and have not been
subject to any later design or electromechanical modifications.
We herewith declare that said products are in conformity with the
provisions of the respective EC directives including all applicable
amendments.
A detailed declaration is available on request and can be ordered
from d&b or downloaded from the d&b website at
www.dbaudio.com.
3.1.1. WEEE Declaration (Disposal)
Electrical and electronic equipment must be disposed of separately
from normal waste at the end of its operational lifetime.
Please dispose of this product according to the respective national
regulations or contractual agreements. If there are any further
questions concerning the disposal of this product, please contact
d&b audiotechnik.
3. Manufacturer's declarations
d&b Y7P/Y10P Manual 1.2 en 11

D2710.EN .01, 03/2016 © d&b audiotechnik GmbH
www.dbaudio.com