D-Link GO-PL-200 User manual

Version 1.0 | 05/06/2013
User Manual
GO-PL-200/GO-PLK-200
Powerline AV Mini Easy Adapter

2D-Link GO-PL-200/GO-PLK-200 User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes.
Manual Revisions
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of
their respective companies.
Copyright © 2013 by D-Link Systems, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Systems, Inc.
Revision Date Description
1.0 May 06, 2013 • Initial release for hardware revision A1
Preface

3D-Link GO-PL-200/GO-PLK-200 User Manual
Table of Contents
Preface .........................................................................................2
Manual Revisions ..........................................................................2
Trademarks ..................................................................................... 2
Product Overview ......................................................................4
Package Contents .........................................................................4
Introduction ................................................................................... 5
Features ............................................................................................ 5
Hardware Overview .....................................................................6
LEDs ........................................................................................... 6
Connection ............................................................................. 7
Hardware Installation ...............................................................8
Push Button Security ................................................................... 9
Powerline Installation Considerations ................................12
Troubleshooting ..................................................................... 14
Technical Specications ........................................................ 15
Table of Contents

4D-Link GO-PL-200/GO-PLK-200 User Manual
Section 1 - Product Overview
GO-PL-200
• D-Link GO-PL-200 Powerline AV Mini Easy Adapter
• Ethernet Cable
• Quick Install Guide
GO-PLK-200
• D-Link GO-PL-200 Powerline AV Mini Easy Adapter x2
• Ethernet Cable x2
• Quick Install Guide
Product Overview
Package Contents

5D-Link GO-PL-200/GO-PLK-200 User Manual
Section 1 - Product Overview
Introduction
D-Link announces a fast, 200Mbps* Powerline AV Mini Easy Adapter which allows you to connect your computers, networking
devices and gaming devices through the most pervasive medium in your house - the electric wiring - and share Internet
connections, share printers, transfer les, play games, and more.
Features
• Provides Ethernet to Powerline Connection
• Fast Data Transfer Rate of Up to 200Mbps*
• One Ethernet port
• Plug & Play, Easy Installation
• Push Button Security
• Power Saving mode
• Quality of Service(QoS)
* Maximum throughput based on theoretical transmission PHY rate. Actual date throughput will vary. Network conditions and environmental factors, including volume of trac
and network overhead, may lower actual data throughput rate. Interference from devices that emit electrical noise, such as vacuum cleaners and hair dryers, may adversely aect
the performance of this product. This product may interfere with devices such as lighting systems that have a dimmer switch, short wave radios, or other powerline devices that
do not follow the HomePlug AV and IEEE1901 standard.

6D-Link GO-PL-200/GO-PLK-200 User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
Power LED
• Solid. The device is receiving electrical
power.
• Blinking. The device is setting itself up
after reset or simple connect button was
pressed or power saving mode enabled.
• O. The device is not receiving electrical
power.
Ethernet LED
• Solid. The Ethernet port is linked.
• O. There is no Ethernet connection.
Powerline LED
• Solid. The device is connected to a Powerline
network.
• O. The device has not found any other compatible
Powerline devices using the same encryption key.
The color indicates the Powerline link rate:
• Green. The Powerline link rate is excellent.
• Amber. The Powerline link rate is good
• Red. The Powerline link rate is fair.

7D-Link GO-PL-200/GO-PLK-200 User Manual
Section 1 - Product Overview
Hardware Overview
Connection
Ethernet Port
Connects to your PC or Ethernet
device through an Ethernet cable.
Simple Connect Button
Press to secure your network or
reset your device back to the
factory default settings. Refer
to page 9 for more information.

8D-Link GO-PL-200/GO-PLK-200 User Manual
Section 2 - Installation
Hardware Installation
Power
Plug in the GO-PL-200 into an AC wall outlet. Note that it is not recommended to connect the GO-PL-200 to a power
strip or UPS.
Note: Power source is conrmed when the Power LED on the GO-PL-200 is illuminated.
Connect the Ethernet Cable
Connect the included Ethernet cable to the Ethernet port
located on the GO-PL-200 and attach the other end of the
Ethernet cable to your PC or Ethernet device. Network
Connectivity is conrmed when the Ethernet LED on the
GO-PL-200 is illuminated.
Power Saving Mode Enabled
When the Ethernet link activity has been down for 5
minutes, the GO-PL-200 will automatically go into power
saving mode. The Power LED will blink intermittently.
WARNING! D-Link powerline devices cannot be congured while in
Power Saving Mode.
1ROOM C
GO-PL-200
PC
2ROOM A ROOM B ROOM C
GO-PL-200GO-PL-200
RouterInternet
PC
GO-PL-200
PC
EXISTING PLC NETWORK

9D-Link GO-PL-200/GO-PLK-200 User Manual
Section 2 - Installation
Understanding Powerline AV Mini Easy Adapter Security
Powerline AV Mini Easy Adapters must use the same encryption key in order to be on the same network. The default encryption
key of each Powerline AV Mini Easy Adapter is HomePlug AV. All Powerline AV Mini Easy Adapters with default encryption key
can communicate with each other.
It’s recommended to create a private encryption key for network security purposes. The private encryption key allows you to
protect your network from unauthorized access via the Powerline network. To create a private encryption key, please follow
the steps below:
1. All Adapters
Plug in all the adapters to be congured and make sure each device’s encryption key is set to HomePlug AV (default value). If
the encryption key is not set to the default value, press the Simple connect button for 10 seconds to reset it to the default value.
2. First Adapter
Press the Simple Connect Button of the rst adapter for no more than three seconds.
The Power LED will start blinking after you release the button. The adapter will create a private, randomly generated encryption
key that each Powerline AV Mini Easy Adapter will use.
3. Second Adapter
Push Button Security

10D-Link GO-PL-200/GO-PLK-200 User Manual
Section 2 - Installation
Within two minutes of pushing the Simple connect button of the rst adapter, press the Simple Connect Button on the second
adapter in your Powerline network for no more than three seconds. The Power LED will start blinking after you release the
button.
Note: Both Simple connect buttons must be pressed within two minutes.
Your Powerline network is now securely congured with the same network encryption key. The adapters will remember the
security settings even if they are unplugged.
Note: To change the private encryption key, please reset the adapter back to its default value by pressing the Simple Connect
button for 10 seconds and then follow the security setup procedure above.
4. Adding More Adapters
If you would like to add more than two adapters, press the Simple Connect Button on the additional adapter for no more than
three seconds. The Power LED will start blinking after you release the button.
press the Simple Connect Button on any adapter in your existing Powerline network for no more than two seconds. The Power
LED will start blinking after you release the button.
Note: Both Simple connect buttons must be pressed within two minutes.
Now your new adapter will be able to connect to your existing Powerline network.