D-Link DCS-932L Safety guide

D-Link Technical Support – How to connect the DCS-932L wirelessly. Page 1of 7
How to connect the DCS-932L wirelessly
This document will detail how to change the DCS-932L configuration to be connecting
wirelessly to your Wireless Access oint, without having to run through the Setup Utility
again.
Ensuring the firmware remains up to date can assist with functionality / improved
performances as well as adding additional features.

D-Link Technical Support – How to connect the DCS-932L wirelessly. Page 2of 7
It is assumed that you have followed the setup guide "How to install the DCS-932L" and during the
installation you sele ted the "Wired" onfiguration. It's therefore assumed that your DCS-932L is onne ted
using an Ethernet able. Continue reading to hange this onfiguration to be onne ting wirelessly instead.
1. You will need to know the IP Address of your DCS-932L. There are two ways in whi h this an be done.
Setup Utility:
Run through the Setup Utility sele ting the default options until you get to a heading "First, sele t your
amera":
We now have the IP Address whi h is assigned to the DCS-932L. Please remember the urrent IP Address
assigned as we will require it shortly. Your assigned IP Address may also be different to my example. You
may lose the Setup Utility now.
Checking your Router's Web Configuration:
Login to your Router's Web Configuration and refer to its DHCP Client List. Please he k your with Router's
Do umentation and or Manufa turer as DHCP Client List may be alled another name:
The below illustration is from a D-Link DIR-825 and its DHCP Client List is referred as the 'Dynami DHCP
Clients':
We now have the IP Address whi h is assigned to the DCS-932L. Please remember the urrent IP Address
assigned as we will require it shortly. Your assigned IP Address may also be different to my example.

D-Link Technical Support – How to connect the DCS-932L wirelessly. Page 3of 7
2. Now we know the assigned IP Address, please type your IP Address into your Internet Browser, then press
Enter or Go:
3. You will need to login with your username and password that you assigned to your DCS-932L during the
Setup Utility pro ess:

D-Link Technical Support – How to connect the DCS-932L wirelessly. Page 4of 7
4. When you have su essfully a essed the DCS-932L Web Configuration you will see a similar illustration
on your Internet Browser as the below illustration:
NOTE: Your Live Video results may differ.
5. Cli k on the Setup menu, followed by li king on the Wireless Setup heading:

D-Link Technical Support – How to connect the DCS-932L wirelessly. Page 5of 7
6. Cli k on the Enable option, then li k on the Save Settings button:
7. Now li k on the Site survey button:

D-Link Technical Support – How to connect the DCS-932L wirelessly. Page 6of 7
8. Sele t your SSID (wireless name):
9. S roll down (if required) and press the sele t option:

D-Link Technical Support – How to connect the DCS-932L wirelessly. Page 7of 7
10. Now type in your orre t wireless password into the Pre-Shared Key field, then press the Save Settings
button:
11. Now remove the Ethernet able from the DCS-932L.
NOTE: When you disconnect the Ethernet ca le the power LED will turn red, then come green again within
a few seconds.
12. Now after 30 seconds li k on Maintenan e > System and li k the Reboot the Devi e button:
12. When the DCS-932L has ompleted the reboot pro ess you will know that your onne ted wirelessly as
you should also be able to li k on the other menu's in the DCS-932L Web Configuration and when viewing
the Live Video menu, moving obje ts should also be visible in the DCS-932L Web Configuration without
needing an Ethernet able onne ted.