D-Link DI-514 - Wireless Router User manual

1
DI-514
2.4GHz Wireless
Router
5V DC Power Adapter
©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and
specifications subject to change without notice. DI-514. 10242003
Before You Begin
1. If you purchased this router to share your high-speed Internet connection with other
computers, you must have either an Ethernet-based Cable or DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for configuring
the DI-514 Wireless Router. The DI-514 acts as a DHCP server and will assign all
the necessary IP address information on your network. See Appendix at the end
of this Quick Installation Guide or the Manual on the CD-ROM for setting each
network adapter to automatically obtain an IP address.
Check Your Package Contents
DI-514 2.4GHz Wireless Router
CD-ROM (containing Manual and Warranty)
Ethernet (Straight Through) Cable
If any of the above items are missing, please contact your reseller.
This product can be set up using
any current web browser, i.e.,
Internet Explorer 6 or Netscape
Navigator 6.2.3.
Using a power supply
with a different voltage
rating will damage this
product and void the warranty

2
Connecting The DI-514 Wireless Router
To Your Network
D. Antenna
Used to
wirelessly
connect to
802.11b
adapters.
C. LAN PORTS These are
the connections for
Ethernet cables to Ethernet
enabled computers.
Reset Button Pressing this button restores the
Router to its original factory default settings.
B. WAN PORT This is
for the connection of an
Ethernet cable to the
Cable or DSL modem
A. First, connect the power adapter to the receptor at the back panel of the
DI-514 and then plug the other end of the power adapter to a wall outlet or power
strip. The Power LED will turn ON to indicate proper operation.
B. 1. Power off your Cable or DSL modem; some devices may not have a on/off switch
and will require you to unplug the power adapter. Now, the DI-514 should be
powered on and the Cable / DSL modem should be turned off.
2. Cable / DSL modem (Power Off) – DI-514 (Power On)
Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL modem.
After the Ethernet cable is securely connected, power on the Cable / DSL modem by
turning on the unit or plugging in the power adapter.
3. Cable / DSL modem (Power On) – DI-514 (Power On)
Insert the other end of the Ethernet cable to the WAN PORT on the back panel of the
DI-514. The WAN LED light will illuminate to indicate proper connection. If the WAN
LED is not illuminated, please go back to step B1 and repeat the instructions.
C. Insert an Ethernet cable to LAN port 1 on the back panel of the DI-514 and an
available Ethernet port on the network adapter in the computer you will use to
configure the DI-514. The LED light for LAN Port 1 will illuminate to indicate proper
connection. (Note: The LAN Ports on the DI-514 are Auto-MDI/MDIX. Meaning you
can use a straight-through or crossover-Ethernet cable to the LAN Ports.)
D. Computers equipped with 802.11b wireless adapters will be able to connect to the
DI-514. The DWL-650+ Air Wireless Cardbus Adapter and the DWL-520+ Air
Wireless PCI Adapter will be able to connect out of the box with the router using their
default wireless settings.
A. Receptor for
Power Adapter.

3
Restart Your Computer
Connecting Additional Computers To
The DI-514
WAN LED – a solid light
indicates connection on the
WAN port. This LED blinks
during data transmission.
POWER LED – a solid
light indicates a proper
connection to the power
supply.
Status LED – a
blinking light indicates
that the DI-514 is ready.
When you have completed the steps in this Quick Installation Guide, your connected
network should look similar to this:
Using additional Ethernet (CAT5 UTP) cables, connect your Ethernet-equipped
computers to the remaining Ethernet LAN ports on the back panel of the DI-514.
WLAN LED – a solid
light indicates that the
wireless segment is
ready. This LED
blinks during wireless
data transmission.
LOCAL NETWORK LEDs –
a solid light on the port
indicates a connection to
an Ethernet enabled
computer on ports 1-4.
This LED blinks during
data transmission.

4
Once you have logged in, the Home
screen will appear.
Click Run Wizard
Using The Setup Wizard
The logon pop-up screen will appear.
Open your Web browser and
type “http://192.168.0.1” into the
URL address box. Then press the
Enter or Return key.
Type “admin” for the username and
leave the password field blank.
Click OK

5
The Setup Wizard (continued)
You will see the following screens
Set up your new password.You
have the option to establish a
password.
Click Next
Click Next
Choose your time zone from the
drop down list.
Click Next

6
If you selected Dynamic IP Address,
this screen will appear: (Used mainly
for Cable Internet service.)
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You can
also manually type in the MAC
address.
The Setup Wizard (continued)
Select your Internet Connection.
You will be prompted to select the
type of Internet connection for your
router.
If you are unsure of which setting
to select, please contact your
Internet Service Provider.
Click Next
Click Next
This setup should be done on
the computer that is registered
on the ISP’s network.
Please continue to Wireless Setup.
A this point, the setup wizard will try
to auto-detect your Internet connec-
tion type. If you have a Dynamic or
PPPoE connection, you will be
brought to their corresponding page.
Otherwise, you will see the following screen:

7
The Setup Wizard (continued)
If your ISP requires a Static IP
Address, and this option is selected,
then this screen will appear:
Enter the IP address information
originally provided to you by your ISP.
You will need to complete all the
required fields.
Click Next
Please continue to Wireless Setup.
If your ISP uses PPPoE (Point-to-
Point Protocol over Ethernet), and
this option is selected, then this
screen will appear: (Used mainly for
DSL Internet service.)
Please be sure to remove any
existing PPPoE client software
installed on your computers.
Enter in the username and pass-
word provided to you by your ISP.
Click Next
Please continue to Wireless Setup.

8
If you wish to use encryption for your
802.11b network, the DI-514 is
capable of two levels of wireless
encryption - 64-bit and128-bit. By
default the encryption is disabled.
You can change the encryption
settings for more secure wireless
communication.
The Setup Wizard (continued)
The default wireless settings for your
802.11b wireless network are:
SSID = default
Channel = 6
You can change these settings to
match an existing wireless network.
Click Next
Wireless Setup
Click Next

9
Your Setup is Complete!
Click Restart
Click Close
Test Internet Connection
You will be returned to the Home tab.
For additional settings or informa-
tion, refer to the Advanced,
Tools, or Status tabs on the web-
management interface; or to the
Manual located on the CD.
Then relaunch your Web browser
(i.e., Internet Explorer or Netscape
Navigator), to link to your favorite
Web site to test your Internet
connection.
Click to Exit

10
To connect to the network, make sure
the network adapter in your computer
is configured properly. Here’s how to
configure the network adapter to obtain
an IP address automatically for the
DI-514 Wireless Router.
APPENDIX
Click Internet Protocol (TCP/IP)
Click Properties
Select Obtain an IP address
automatically
Restart your
computer
Click OK
For Microsoft Windows XP: Go to
Start > right click on My Network
Places > select Properties > Right
click on the Network Connection
associated with the Ethernet adapter
and select Properties (i.e., D-Link
DFE-530TX+).